Programmatur tal-Modulu XTOOL X2MBIR

Ċaħda
Please read this manual carefully before using X2Prog Module Programmer (herein after referred to as X2Prog). Shenzhen Xtooltech Intelligent Co., Ltd. (herein after referred to as “Xtooltech”) does not assume any liability in case of misuse of the product. Pictures illustrated here are for reference only and this user manual is subject to change without prior notice.

Deskrizzjoni tal-Prodott

X2Prog huwa Programmatur tal-Moduli li jista' jaqra, jikteb u jimmodifika d-dejta taċ-ċippa EEPROM u MCU permezz tal-metodu BOOT. Dan l-apparat huwa adattat għal tuners jew mekkanikisti professjonali tal-vetturi, li jipprovdi funzjonalitajiet bħall-ikklonjar tal-moduli, il-modifika, jew is-sostituzzjonijiet għall-ECU, BCM, BMS, dashboards jew moduli oħra. X2Prog huwa kapaċi wkoll ma' moduli ta' espansjoni oħra pprovduti minn Xtooltech, li jippermetti aktar funzjonijiet bħall-ipprogrammar BENCH, il-kodifikazzjoni tat-transponder u ħafna aktar.

Prodott View

• ① DB26 Port: Use this port to connect with cables or wiring harnesses.
• ② Indicators: 5V (Red / Left): This light will be turned on when X2Prog receives 5V power input. Communication (Green / Middle): This light will be flashing when the device is communicating. 12V (Red / Right): This light will be turned on when X2Prog receives 12V power input.
• ③ ④ Expansion Ports: Use these ports to connect with other expansion modules.
• ⑤ 12V DC Power Port: Connect to 12V power supply when necessary.
• ⑥ USB Type-C Port: Use this USB port to connect with XTool devices or PC.
• ⑦ Nameplate: Show product information.

Rekwiżiti tal-Apparat

• XTool devices: APP version V5.0.0 or higher;
• PC: Windows 7 jew ogħla, 2GB RAM

Konnessjoni tal-Apparat

Espansjoni u Konnessjoni tal-Kejbil

X2Prog is adapted to various expansion modules or cables for extra functions. Different modules are needed in different situations.
To install expansion modules, directly connect the modules to X2Prog using the expansion ports (32/48PIN) or the DB26 port.
Multiple expansion modules can be installed on X2Prog at the same time. When you are operating, check the device and see which modules are necessary.

Kif Taqra u Tikteb EEPROM

Permezz tal-Bord tal-EEPROM

*EEPROM Board only comes with X2Prog standard pack.
When reading EEPROM in this method, the chip should be taken off from the ECU and needs to be soldered onto the EEPROM board.

Hemm modi oħra kif taqra l-EEPROM bl-użu ta' moduli ta' espansjoni. Jekk jogħġbok iċċekkja d-dijagrammi fuq l-app u ara kif tista' tikkonnettja maċ-ċippa.

Kif Taqra u Tikteb MCUs

BOT

When reading MCU in this method, the wiring harness should be soldered to the ECU board according to the wiring diagram, and a 12V power supply should be connected to X2Prog.

Meta taqra l-MCU b'dan il-metodu, il-wajers għandhom ikunu pplaggjati mal-port tal-ECU skont id-dijagramma tal-wajers, u provvista ta' enerġija ta' 12V għandha tkun imqabbda ma' X2Prog.

Ikkuntattja l-Istati Uniti

• Servizzi tal-Klijent:
  supporting@xtooltech.com
• Uffiċjali Websit:
  https://www.xtooltech.com/
• Indirizz:
  17&18/F, Bini A2, Belt Kreattiva, Liuxian Avenue, Nanshan District, Shenzhen, Ċina
• Corporate & Business:
  marketing@xtooltech.com

© Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, All Rights Reserved

Informazzjoni ta' Konformità

Konformità tal-FCC

FCC ID: 2AW3IM604
Dan l-apparat jikkonforma mal-Parti 15 tar-Regoli tal-FCC. It-tħaddim huwa soġġett għaż-żewġ kundizzjonijiet li ġejjin:

1. Dan l-apparat ma jistax jikkawża interferenza ta 'ħsara
2. Dan l-apparat għandu jaċċetta kwalunkwe interferenza riċevuta, inkluża interferenza li tista 'tikkawża tħaddim mhux mixtieq.

Twissija
Bidliet jew modifiki mhux approvati espressament mill-parti responsabbli għall-konformità jistgħu jħassru l-awtorità tal-utent biex iħaddem it-tagħmir.

Nota
Dan it-tagħmir ġie ttestjat u nstab li jikkonforma mal-limiti għal apparat diġitali tal-Klassi B, skont il-Parti 15 tar-Regoli tal-FCC. Dawn il-limiti huma mfassla biex jipprovdu protezzjoni raġonevoli kontra interferenza dannuża f'installazzjoni residenzjali.
This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Orjenta mill-ġdid jew iċċaqlaq l-antenna li tirċievi.
• Żid is-separazzjoni bejn it-tagħmir u r-riċevitur.
• Qabbad it-tagħmir ma' żbokk fuq ċirkwit differenti minn dak li miegħu huwa konness ir-riċevitur.
• Ikkonsulta lin-negozjant jew tekniku tar-radju/TV b'esperjenza għall-għajnuna.

Dikjarazzjonijiet ta' Twissija ta' Espożizzjoni RF:
Dan it-tagħmir jikkonforma mal-limiti ta' espożizzjoni għar-radjazzjoni FCC stabbiliti għal ambjent mhux ikkontrollat. Dan it-tagħmir għandu jiġi installat u mħaddem b'distanza minima ta' 20cm bejn ir-radjatur u l-korp.

Parti Responsabbli

• Company name: TianHeng Consulting, LLC
• Indirizz: 392 Andover Street, Wilmington, MA 01887, l-Istati Uniti
• E-mail: tianhengconsulting@gmail.com

Dikjarazzjoni ISED

• IC: 29441-M604
• PMN: M604, X2MBIR
• HVIN: M604

Dan l-apparat fih trasmettitur(i)/riċevitur(i) eżentati mil-liċenzja li jikkonformaw mal-RSS eżentati mil-liċenzja tal-Innovation, Science and Economic Development Canada.
CAN ICES (B) / NMB (B).
This device meets the exemption from the routine evaluation limits in section 6.6 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment complies with IC exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

Dikjarazzjoni ta' konformità
Hereby, Shenzhen XTooltech Intelligent Co., Ltd declares that this Module Programmer is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.

UKCA
Hereby, Shenzhen XTooltech Intelligent Co., Ltd declares that this Module Programmer satisfies all the technical regulations applicable to the product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091) and declare that the same application has not been lodged with any other UK Approved Body.

FAQ

• M: X'inhuma r-rekwiżiti tal-apparat għall-użu tal-Modulu X2MBIR Programmatur?
  A: The X2MBIR Module Programmer requires XTool devices with APP version V5.0.0 or higher and a PC running on Windows 7 or higher with a minimum of 2GB RAM.
• M: Kif naqra u nikteb id-dejta tal-EEPROM bl-X2Prog?
  A: To read and write EEPROM data, use the provided EEPROM Board included in the standard pack. Remove the chip from the ECU and solder it onto the EEPROM board.
• M: Nista' nuża diversi moduli ta' espansjoni simultanjament mal- X2Prog?
  A: Yes, multiple expansion modules can be installed on X2Prog at the same time. Ensure you connect them correctly to enhance functionality.

Dokumenti / Riżorsi

Programmatur tal-Modulu XTOOL X2MBIR [pdfGwida għall-Utent M604, Programmatur tal-Modulu X2MBIR, X2MBIR, Programmatur tal-Modulu, Programmatur

Referenzi

• Manwal għall-Utent