THIRD REALITY ZB2 Smart Button User Manual

Smart Button ZB2
Gwida Quick Start

Kontenut tal-Pakkett

Speċifikazzjonijiet

Irrisettja l-Fabbrika

Press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.

Setting up your Smart Button ZB2

1. Follow instructions to set up your compatible Zigbee hub.
2. Use the Micro-USB charging cable included in the package to connect the button to a power adapter (not included) to active the Smart Button ZB2.
3. You can also press and hold buttons 1 and 2 for 10 seconds, the Smart Button ZB2 will be activated once it beeps three times. The device will automatically enter pairing mode.
   Note: It will exit pairing mode automatically if not successfully paired within 3 minutes, to put it into pairing mode again, press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.
4. After the pairing is completed, the device will beep once. you can create routines in the corresponding smart home App or platform to control other connected devices. THIRDREALITY Smart Button ZB2 features three buttons (button 1 & button 2 & button  3), each supporting three control settings: Pressed, Double Pressed and Held. Note: When charging, please connect the button to a power adapter (not included) using the Micro-USB charging cable provided in the package. The Smart Button ZB2 will be fully charged until it beep twice.

Skennja l-kodiċi QR lil view dettalji

https://bit.ly/488mkj9

Issolvi l-problemi

1. How to check if the device is fully charged
   The Smart Button ZB2 will be fully charged until it beep twice.
2. L-apparat mhux se jixgħel
   Recharge the battery, ensure it powers on properly, and note that low temperatures may reduce performance.
3. Cannot charge / No charging response
   Use the original charger, check the charging port, and wait a few minutes in case of over-discharge protection.

Konformità Regolatorja tal-FCC
Dan l-apparat jikkonforma mal-parti 15 tar-Regoli tal-FCC. It-tħaddim huwa soġġett għaż-żewġ kundizzjonijiet li ġejjin: (1) Dan l-apparat ma jistax jikkawża interferenza ta 'ħsara, u (2) dan l-apparat għandu jaċċetta kwalunkwe interferenza riċevuta, inkluż interferenza li tista' tikkawża tħaddim mhux mixtieq.
Kwalunkwe tibdil jew modifika mhux approvata espressament mill-parti responsabbli għall-konformità tista' tħassar l-awtorità tal-utent biex iħaddem it-tagħmir.
Nota: Dan it-tagħmir ġie ttestjat u nstab li jikkonforma mal-limiti għal apparat diġitali tal-Klassi B, skont il-parti 15 tar-Regoli tal-FCC.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Orjenta mill-ġdid jew riloka l-antenna li tirċievi.
– Żid is-separazzjoni bejn it-tagħmir u r-riċevitur.
– Qabbad it-tagħmir fi żbokk fuq ċirkwit differenti minn dak li miegħu huwa konness ir-riċevitur.
– Ikkonsulta lin-negozjant jew tekniku b'esperjenza tar-radju/TV għall-għajnuna.
The device has been evaluated to meet general RF exposure requirement. The device can be used in the exposure condition without restriction. 06

Għal garanzija limitata, jekk jogħġbok żur
https://thirdreality.com/faq-help-center/
Għal appoġġ għall-klijent, jekk jogħġbok ikkuntattjana fuq
info@3reality.com jew żur www.thirdreality.com
Għal mistoqsijiet dwar pjattaformi oħra, żur il-korrispondenti
platform’s application/support platform.