Manwali u Gwidi għall-Utent ta' Cell2

Cell2 B14 Manwal għall-Utent tal-Beacons LED tal-Immontar manjetiku

27 ta’ Frar, 2023

Cell2 B14 Magnetic Mount LED Beacons WIRING & OPERATION RED: To +VDC BLACK: To Chassis Ground (-) WHITE: For Simultaneous or Alternating Flash Group1 Units: (Wiring- \WJ[H]~'jj'~ connected to RED) will flash together. Group2 Units: (Wiring- \WJ[H]~'jj'~ not connected to…

Marka: Cell2

Cell2 EGION-FIT Legion FIT Cruise (H002) Manwal għall-Utent tal-Ispeaker

27 ta’ Frar, 2023

Cell2 EGION-FIT Legion FIT Cruise (H002) Speaker WIRING & FUNCTIONS (AM/AN) Different applications require different functions. It is highly recommended to determine and configure the required functions prior to Installation; (refer to ‘CONTROL WIRES’ section). LIGHTBAR WIRING Functions are activated…

Marka: Cell2

Cell2 CR06-DC Led Flush Mount Kit Manwal għall-Utent

27 ta’ Frar, 2023

Cell2 CR06-DC Led Flush Mount Kit WIRING OPERATION For Flash Pattern Selection While in Warning Mode, momentarily apply +VDC to YELLOW wire: once to next pattern quickly three times to FP#1 (Refer ro Flash Pattern Chart) For Simultaneous or Alternating…

Marka: Cell2

Cell2 SL157 Manwal għall-Utent tad-Dawl tax-Xena Esterjuri

27 ta’ Frar, 2023

Cell2 SL157 Exterior Scene Light WIRING INSTALLATION Place the foam pad onto the desired mounting surface and mark the location for the two mounting screws and the wire routing hole location between the two screw holes. Drill two pilot holes…

Marka: Cell2

Cell2 R0 Xena tal-Immonta fil-wiċċ Lamp Manwal għall-Utent

27 ta’ Frar, 2023

R0 Xena tal-Immonta fil-wiċċ Lamp Manwal għall-Utent R0 Xena tal-Immontar fil-wiċċ Lamp WIRING: To +VDC(fuse rating @ 0.5A)...................................................... RED To Vehicle Chassis Ground: ..........................................................BLACK (For steady-bum models, external flasher may be used for waming purpose.) INSTALLATION (Actual mounting kit will…

Marka: Cell2

cell2 SW830-2 Manwal ta 'Istruzzjoni tal-Panel tal-Kontroll tal-Iswiċċ Multi-Purpose

27 ta’ Frar, 2023

SW830-2 Multi-Purpose Switch Control Panel Instruction Manual INSTALLATION It is essential to install the unit properly to ensure safe and reliable operation. Please read through all instructions thoroughly and carefully before installing the unit. The correct mounting and wiring is…

Marka: Cell2

Cell2 RAYZR Lighthead 3LED TIR Manwal għall-Utent

27 ta’ Frar, 2023

RAYZR Lighthead 3LED TIR User Manual RAYZR Lighthead 3LED TIR WIRING FOR WARNING STICKS RED ........................[+] Warning Mode to +VDC with rated fuse (for correct rating, refer to the Fuse Rating Chart) BLACK .....................to Chassis ground Fuse Rating 2-Head Model…

Marka: Cell2

Cell2 Commander SE4 Traffic Director 8 Lighthead User Manual

27 ta’ Frar, 2023

Commander SE4 Traffic Director 8 Lighthead User Manual INSTALLATION Remove endcap (side without cable) and insert mounting carriage bolts. For Surface Mount, drill 1/4" (6.3mm) holes to the mounting surface. Place Disk Gasket onto each bolt, and insert bolts into…

Marka: Cell2

cell2 LP6 LED Pad Utent Manwal

27 ta’ Frar, 2023

LP6 LED Pad User Manual Surface Mount NOTE: When using adhesive mount, ensure that the mounting surface is clean, dry and well unified before mounting. Connect BROWN wires of all heads together for synchronization. (all heads should be set at…

Marka: Cell2

Cell2 SceneMax Twissija Moduli Manwal għall-Utent

26 ta’ Frar, 2023

SceneMax Warning Modules User Manual SceneMax Warning Modules WIRING MOUNTING DIMENSIONS OPERATION For Flash Pattern Selection: Each Warning Memory may select and save one flash pattern. While activating a warning mode, momentarily apply YELLOW wire to +VDC: Once to next…

Marka: Cell2