NYX HYPERION3 Magnetic Split Controller User Manual

NYX HYPERION3 Magnetic Split Controller

MANWAL TAL-UTENTE

Għażiż Gamer,

Grazzi tax-xiriasinil-prodott tagħna.
Qabel ma tuża l-prodott, jekk jogħġbok aqra l-manwal tal-prodott bir-reqqa.

Kompatibilità

Supports Switch2 host system 20.0 and above

Kontenut tal-pakkett

• Left controller x1,
• Right controller x1,
• Rechargeable center bridge 1,
• Replaceable D-pad x1,
• USB-C charging cable x1,
• Product user manual (warranty card) x1

Technical Parameters of Game Controller

• Product Model: NS-202
• Product Code: NJ22
• Materjal: ABS
• Weight: 215g (for left and right controllers together)
• Input: 5V = 500mA
• Vol Operattivtage: 3.7V
• Kurrent tal-Iċċarġjar: 400mA
• Battery Capacity: Left Controller: 600mAh
• Right Controller: B00mAh
• Operating Current: Without Motor Vibration: ~60mA
• With Motor Vibration: ~I00mA
• Dimensions: Left Controller: 61.2116.7°52.2 mm
• Right Controller: 61.2°116.7°62.2 mm

Techial Parameters of Center Bridge

• Materjal: ABS
• Piż: 50g
• Input: 5V = 1000mA
• Vol Operattivtage: 5V
• Kurrent Operattiv: 800mA
• Charging Current (per side): 200mA
• Dimensions: 115.6°46’16 mm

Deskrizzjoni tal-prodott

Connection Tutorials

NS2

Required System: Version 20.0 or higher

Konnessjoni bil-fili

Align the left controller’s ™’ key and the right controller’s ‘+’ key upwards, then magnetically attach them to the corresponding magnetic ports on both sides of the console. The console will indicate a successful match with a connection animation on both sides.

Konnessjoni Bluetooth

Power on the Switch 2 console. On the main interface, tap the controller icon with your finger, then select the “Change Grip/Order’ screen. Press and hold the SYNC button on the left (o right) controller for 3 seconds until the RGB indicator flashes rapidly, entering Bluetooth pairing mode.

The console will automatically search for and pair with the controller.

After successful connection, the controllers’ RGB indicators will display solid lights in the following channel colors:

• Channel 1: Solid Orange
• Channel 2: Solid Green
• Channel 3: Solid Blue
• Channel 4: Solid Purple

Konnessjoni mill-ġdid tal-Bluetooth

After initial pairing, if the controller is in sleep mode and the console on, press any button (except L3, R3, TURBO) to reconnect via Blustooth (Note: Avoid touching the joysticks during reconnection)

Bluetooth Wake-up

After initial pairing, if both the console and controller are in sleep mode, press the Home button on the right controller to wake up the console and reconnect.

Keylinker App Connection

APP QR Code:

1-Use a mobile browser to scan the QR code or search for “KeyLinker” in your app store to download and install
2-After installation, upon first launch, the app may request relevant permissions; grant them as prompted.
3-Connect your phone’s Bluetooth in Android/iOS mode, find the device named “NYXI NJ22″, and tap to pair.
4-After successful connection, tap the settings button next to the device name to enter the controller customization interface.

5-Buttons can be remapped to any other key. Joystick and trigger curves can be adjusted. Motor vibration intensity can be modified. Turbo function speed can be set. Macro programming allows adjusting interval times. Power-off timing and other settings can also be configured 6-After modifying functions, click *Apply” to save the changes.

Gwida tal-Funzjoni

Funzjoni Turbo

1-Assign Turbo: On the left controller, hold the Turbo button + UP, DOWN, LEFT, RIGHT, ZL, or L. On the right controller, hold Turbo + A, B, X, Y, ZR, or R to assign turbo to that button. Then hold that assigned button to enable rapi The RGB indicator flash frequency matches the turbo speed.

Left controller

Kontrollur it-tajjeb:

2-Auto Turbo: Press and hold the left Turbo button + UP, DOWN, LEFT, RIGHT, ZL, L (for left controller) or the right Turbo button + A, B, X, Y, ZR, R (for right controller) again to set the corresponding buttons to auto turbo mode.

Left controller

Right controller;

3-Cancel Turbo: Press and hold the left Turbo button + UP, DOWN, LEFT, RIGHT, ZL, L (for left controller) or the right Turbo button + A, B, X, Y, ZR, R (for right controller) again to cancel the turbo function for the corresponding buttons.

Kontrollur tax-xellug:

Right controller;

4-Clear All Turbo: Press and hold the left Turbo button (for left controller) or the right Turbo button (for right controller) for 6 seconds.
The controller will vibrate for 1 second, indicating that all turbo assignments for that controller have been cleared.

5-Turbo Speed Adjustment: There are three adjustable speeds: Fast/ Medium / Slow. To increase the turbo frequency, hold Turbo + push the joystick up. To decrease, hold Turbo + push the joystick down. The default speed is Medium. The controller will vibrate briefly each time the turbo speed is adjusted.

Back Button Mapping & Macro Programming

The two customizable buttons GL/GR on the back of the controller can be mapped to specific function keys (GL can be mapped to: UP, DOWN, LEFT, RIGHT, L, ZL, L3, -; GR can be mapped to: A, B, X, Y, R, ZR, R3, +).

Passi ta' Operazzjoni:

1-While connected to the host, hold the TURBO button and press the GL/GR button once, then release to enter the GL/GR button customization mode. The RGB indicator will flash white rapidly, and the controller will vibrate for 1 second as a reminder.

2- After entering GL (or GR) button customization mode, press a desired function key (e.g., L button for GL or A button for GR). The lit indicator will flash once, confirming that the key has been mapped to the corresponding GL/GR button. Press the GL (or GR) button again to exit customization mode for that controller. The controller will vibrate for l second, and the RGB indicator will return to its original channel indication. Follow the above steps to set the GLIGR buttons.

3- During customization, multiple function keys can be input in sequence for a single GL/GR button, then press the GL/GR button again to exit and save as a macro key. In-game, pressing this key will execute the sequence according to the interval times set during programming. When GL/GR is used as a macro key, a single custom button can store up to 21 key inputs. Once 21 keys are entered, the macro will be saved automatically, and the programming mode will exit, restoring the current channel indicator.

4- Clearing GL/GR Custom Button Functions: While connected to the host, hold the TURBO button and press the GL/GR button once, then release to enter GLIGR customization mode. The RGB indicator will flash white rapidly, and the controller will vibrate for l second. Briefly press the GL/GR button to clear the custom functions assigned to it. A successful clear is indicated by l second of vibration. After clearing, the button will return to a no-function state.

Aġġustament tal-Intensità tal-Vibrazzjoni

1-The vibration intensity of the grip motors can be adjusted to 3 levels (Off/Low/High). The factory default is Low, and the Off level disables vibration.

2-For the left or right controller, hold the TURBO button and push the joystick left (decrease) or right (increase) to adjust the grip vibration intensity. The levels cycle through Off –> Low –> High. After each adjustment using the combo, the controller will vibrate at the corresponding intensity for l second. When set to Off, there will be no vibration. The current vibration intensity will be remembered even after the controller is powered off.

Dawl RGB

1-Hold the TURBO button and single-press the left controller’s – button or the right controller’s + button to cycle through one mode per press. There are multiple lighting effect modes. including eight solid color modes (Red, Orange, Yellow, Green, Blue, Indigo, Purple, Pink) and one mixed-color mode (the four LEDs are: top-left Yellow, bottom-left Blue, top-right Red, bottom-right Green).

2-Hold the TURBO button and double-press the left controller’s L3 or the right controller’s R3 button to turn off all RGB lighting (including the RGB joystick ring and RGB channel indicator).

• Press the same combination again to activate mixed-color breathing mode (LEDs: top-left Yellow, bottom-left Blue, top-right Red, bottom-right Green).
• Press the combination a third time to activate mixed-color flowing light mode (Yellow, Blue, Red, Green) – the left joystick ring flows clockwise, and the right joystick ring flows counter-clockwise.

3-Hold the TURBO button and press and hold the left controller’s L3 or the right controller’s R3 button. The brightness will cycle from dim to bright. Release the button to set the brightness to the current level. Each operation is confirmed by a vibration prompt. The controller will remember the last lighting effect state (except in lock mode, where it will revert to mixed-color flowing light mode upon the next power-on).

Qawwa mixgħul/mitfi

Power On (Reconnect): In off state, press any button to power on and enter reconnect mode.
Power On (Pairing): In off state, hold SYNC for 3 seconds to power on and enter pairing mode.
Power Off: In on state, hold the left controller’s Capture button/ right controller’s Home button for 3 seconds.
Immediate Power Off: In on state, short press the SYNC button. Auto Power Off: The controller will power off if the connected host enters sleep mode or turns off Bluetooth.

Twissija ta' Batterija Baxxa

Low Battery WarningWhen the controller’s battery voltage drops below 3.5V during connected use, the RGB indicator flashes red rapidly to warn that the controller needs charging. If the voltage falls below 3.4V, the controller automatically shuts down.

Auto Sleep

When connected to a host, the controller enters sleep mode after 10 minutes of inactivity. (Sleep timer can be adjusted in the App.)

Iċċarġjar

Via Console Charging: Magnetically attach controllers to the sides of the Switch2 console. While the console is charging via its adapter, the controllers also charge. The RGB indicator breathes in its current color and stays solid when fully charged.

Via Controller’s USB Port Charging: Connect USB cable directly to the controller. The RGB indicator breathes red while charging and turns off when fully charged. (Note: Cannot charge via controller’s USB port while connected to a host.)

Via Center Bridge Charging: Connect a charger to the center bridge’s charging port. Both left and right charging indicators on the bridge will flash red for 0.5s, then green for 0.5s, then turn off, indicating successful self-test and standby mode. Place a controller into a charging slot: its corresponding indicator lights solid red. It turns solid green when fully charged. Removing the controller turns off its indicator.

Irrisettja

If the controller malfunctions (e.g., button confusion, freeze, connection failure), try resetting it.

Metodu: Press and hold the HOME or Capture button for 10 seconds, or short press the SYNC button to reset the controller state.

Modalità Lock

Activate: With the controller off, press and hold the SL + SYNC (MODE) buttons for 5 seconds. After the RGB indicator flashes red slowly 3 times, the controller enters lock mode. Pressing any button will not wake it.

Deactivate: Connect the controller to a host magnetically or plug in a USB cable for charging. This exits lock mode, allowing wake-up via any button.

Kalibrazzjoni tal-Ġiroskopju

Left Controller: In sleep mode, press the combo IL + UP + CAP
(Capture button)) simultaneously. Enter calibration mode (RGB indicator flashes cyan slowly). Place the controller flat on a level surface/in a jig. Press (-1 , wait a moment to exit calibration mode.

Kalibrazzjoni kompluta.

Right Controller: In sleep mode, press the combo IR+ X + HOME) simultaneously. Enter calibration mode (RGB indicator flashes cyan slowly). Place the controller flat on a level surface/in a jig. Press l+J wait a moment to exit calibration mode. Calibration complete. Alternative Method via Host: On the console, go to Settings > Controllers & Sensors> Calibrate Motion Controls, then press and hold’+” or”-“.

Kalibrazzjoni tal-Joystick

After connecting to the host, go to Settings > Controllers & Sensors > Calibrate Control Sticks to calibrate the joysticks.

Firmware Upgrade

1-0TA via Phone: Connect to the Keylinker App and use the OTA upgrade option in the menu.
2-Via PC Software: Start the latest firmware upgrade software on a PC. With the controller off, hold the L3 (left joystick) or R3 (right joystick) button, then connect via USB cable. Once the “Upgrade” button becomes clickable, click it to start the upgrade.

3-Firmware upgrades do not delete the controller’s saved settings.

Mudell: NS-202

This device complies with part 15 of the FCC Rules. Operatio  is subject to the following two condiions:
(1) Dan l-apparat jista 'ma jikkawżax interferenza ta' ħsara, u
(2) dan l-apparat għandu jaċċetta kwalunkwe interferenza riċevuta, inkluża interferenza li tista 'tikkawża tħaddim mhux mixtieq.

Twissija tal-FCC:

Kwalunkwe Tibdil jew modifika mhux approvata espressament mill-parti responsabbli għall-konformità tista' tħassar l-awtorità tal-utent biex iħaddem it-tagħmir.

Nota: Dan it-tagħmir ġie ttestjat u nstab li jikkonforma mal-limiti għal apparat diġitali tal-Klassi B, skont il-parti 15 tar-Regoli tal-FCC. Dawn il-limiti huma mfassla biex jipprovdu protezzjoni raġonevoli kontra interferenza dannuża f'installazzjoni residenzjali. Dan it-tagħmir jiġġenera użi u jista 'jirradja enerġija ta' frekwenza tar-radju u, jekk mhux installat u użat skont l-istruzzjonijiet, jista 'jikkawża interferenza ta' ħsara għall-komunikazzjonijiet bir-radju.

Madankollu, m'hemm l-ebda garanzija li l-interferenza ma sseħħx f'installazzjoni partikolari. Jekk dan it-tagħmir jikkawża interferenza ta' ħsara għar-riċezzjoni tar-radju jew tat-televiżjoni, li tista' tiġi determinata billi jintefa u jinxtegħel it-tagħmir, l-utent huwa mħeġġeġ jipprova jikkoreġi l-interferenza b'waħda jew aktar mill-miżuri li ġejjin:

• Orjenta mill-ġdid jew iċċaqlaq l-antenna li tirċievi.
• Żid is-separazzjoni bejn it-tagħmir u r-riċevitur.
• Qabbad it-tagħmir fi żbokk fuq ċirkwit differenti minn dak li miegħu huwa konness ir-riċevitur.
• Ikkonsulta lin-negozjant jew tekniku tar-radju/TV b'esperjenza għall-għajnuna.

L-apparat ġie evalwat biex jissodisfa r-rekwiżit ġenerali ta' espożizzjoni RF.
L-apparat jista 'jintuża f'kundizzjoni ta' espożizzjoni portabbli mingħajr restrizzjoni.

The symbol means the product should not be disposed of with household waste but be brought to an appropriate collection point to enable recycling. According to loca l regulations, do not dispose of the product or rechargeable battery with normal household waste.

Appropriate disposal of used products and rechargeable batteries helps to prevent negative impacts on the environment and human health

PREKAWZJONIJIET

Do not oxpose o s

ponotdisassembe

Android drop it

Evita temperatura estremament għolja jew baxxa

MAGĦMULA FIĊ-ĊINA

Manifattur: Shenzhen MIKE Morgen Technology Co., Ltd
Address: Room 302,Building 5,Zone C,Jinxiu Huacheng Park Bantian
Street,Longgang District,Shenzhen
Applikant: NYXI Gaming Inc
Address: 4520 Centennial Bivd NUM1004, Colorado Sorinas CO 80919

Declaration of Conformity C E
Mudell: NS-202
Product Code: NJ22
The product conforms to EC standards for radio interference. Here, Shenzhen
MIKE Morgen Technology Co.,Ltd. In Shenzhen announces that NS-202 radio
equipment conforms to the Directive. EN IEC 62368-1:2020+A11:2020, EN
50663:2017, EN 62479:2010, ETSI EN 301 489-1 V2.23(2019-11), ETSI EN
301 489-17 V3.2.4(2020-09), ETSI EN 300 328 V2.2.2(2019-07).
It-test sħiħ tad-Dikjarazzjoni ta' Konformità tal-UE jista' jinstab fuq:
www.nyxigame.com

FAQ

Q: Nista 'nimmodifika dan l-apparat?

A: No. Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment, according to FCC regulations.

Q: What should I do if the device is causing interference to other electronics?

A: This device is designed not to cause harmful interference. If you believe it is, try moving the device to a different location or separating it from other electronic equipment.

Q: What if other devices are interfering with this one?

A: This device is designed to accept any interference received. If external interference is causing undesired operation, try to identify and mitigate the source of the interference. This might involve moving the interfering device or this device.

Q: Is this device safe regarding RF exposure?

A: Iva, l-apparat ġie evalwat biex jissodisfa r-rekwiżiti ġenerali ta 'espożizzjoni RF.