NOTHING Fixed Frame Screen Instruction Manual

NOTHING Fixed Frame Screen

Thank you for choosing to use our product! For your better use of the product, please read and keep this manual carefully before installation and use.

Every screen undergoes special quality checks. The manufacturer records a video of each screen produced in the factory to document the condition of the screen as ii leaves the factory. We recommend that you also record a video for documentation when unpacking the screen. This will facilitate the manufacturer in processing any service requests in case of issues. Damage that occurs during the installation cannot be claimed. Therefore, please be extremely careful as the screen material is very fragile, and avoid folding or denting it.

Partijiet

Prekawzjonijiet

1. Biex tiżgura l-effett tal-projezzjoni u l-kwalità ta' dan il-prodott, jekk jogħġbok osserva r-rekwiżiti operattivi li ġejjin.
2. Meta tgħaqqad, sib art jew mejda ta 'daqs xieraq. Il-wiċċ għandu jkun nadif u ħieles minn kwalunkwe ostaklu. L-art jew il-mejda għandhom ikunu mgħottija b'materjali nodfa bħal drapp, film, kutri, eċċ.
3. Immaniġġja b'attenzjoni waqt l-installazzjoni biex tevita korriment personali jew ħsara lill-proprjetà.
4.  Do not touch the surface of the projection screen with your hands.
5. Tmissx il-wiċċ tal-projezzjoni b'oġġetti li jaqtgħu jew iebsin biex tevita li tagħmel ħsara lill-materjal tal-iskrin. Tiktibx jew tpinġix fuq l-iskrin.
6. Żomm it-tfal 'il bogħod mill-iskrin biex tevita inċidenti.
7. Il-wiċċ tal-iskrin għandu jitnaddaf u jiġi ttrattat regolarment, u huwa rakkomandat li tieħu ħsiebha darba kull ġimgħatejn.
   Please use a soft cotton cloth to gently wipe (dip some water), and it is not advisable to use any chemical cleaners or alcohol.

Arma l-qafas

1. Iftaħ il-kaxxa tal-imballaġġ u kkategorizza u irranġa l-komponenti kif suppost, u qabbel il-kwantitajiet mal-lista ta' kontroll "1.0 Partijiet".
2.  The horizontal frame is a segmented splicing type, and the two horizontal inner frames are spliced correspondingly as shown in the figure (Note: There is a mark in the middle of the splicing strip of the inner frame, and the splicing position must be guaranteed to be at the mark).
3. First, insert the four corner connectors into the vertical inner frame, as shown in the diagram.
4. Assemble the horizontal and vertical inner frames according to the diagram. After completing the assembly of the inner frames, secure the corners with M5X5 screws, and then install the support rods.

Arma l-iskrin

1.  Wear gloves (to avoid fingerprints on the screen that cannot be erased).Lay a clean cloth I’ non a flat, clean level countertop (or floor) that won’t hurt the screen.
2.  Take out the screen from the package, put the screen face down,to unfold the curtain roll, spread it flat on the cloth on the table, and then insert the glass fiber strips into the around the screen according to the length as shown below. Nota importanti:
   Jekk huwa skrin li jirrifjuta d-dawl ambjentali b'throw ultra-short-throw, jekk jogħġbok ikkoopera ma' żewġ persuni waqt l-assemblaġġ, evita li l-iskrin jintlewa jew li jkun hemm impatt ta' frizzjoni minn oġġetti iebsin.
3. Place the assembled border on the screen. Note: The ultra-short focus anti-light scree has an up-and-down direction (other curtains have no direction). If it is an anti-light screen it should be matched with the direction of the frame. Adjust the position of the screen according to the lines marked on the four corners of the screen.
4.  Hook the screen on the frame with a tension spring. To hook the tension spring, please follow the following sequence, first, hook 1~8 springs; then hook springs 9~12, and then hook other springs from the middle spring to both sides in turn. Please refer to the attache drawing for the installation method of the tension spring
5. Wara li tiddendel il-molla, poġġi l-iskrin bilwieqfa u ċċekkja l-wiċċ ċatt tal-iskrin. Jekk ikun hemm xi irregolarità, il-molla trid tiġi aġġustata lokalment sakemm tkun livellata.
6. Is restored to the position of 4.4, ready to install the frame.

Outside frame installation

1. Place the outer frame against the frame screen, align the four corners, and lock the inner and outer frames with M4X8 screws. Note: If there is a LOGO on the frame, it should be installed at the bottom of the screen.
2. Adjust the outer frame at the corner to the smallest gap, and then tighten the screws. Lock the corners one by one according to this method, and finally deal with the splicing of the horizontal outer frame (if the gap is found to be too large, you can push the left and right outer frames inward)
3. Finally, put the corner protectors on the four corners of the frame.

Screen install

1. L-ewwel ikkonferma l-parentesi tal-ħajt ta' fuq u ta' taħt u d-direzzjoni tal-installazzjoni
2. Install wall hangers on the wall according to screen size. Required tools: level, hammer drill, pencil, ladder, etc. As shown below, the horizontal direction is about 30cm away from both sides of the screen. Please estimate the installation position of the screen before installing the wall pendants. The height of the lower edge of the screen from the ground is generally about 600″800mm.
3. Hang the screen on the wall according to the method shown in the picture.

FAQs