Triq M5STACKamp-S3Bat Embedded Core Module
Deskrizzjoni
Stamp-S3Bat is an embedded core module integrated with power management. It utilizes the ESP32-S3-PICO-1-N8R8 as the main control core, supports 2.4GHz Wi-Fi, and comes with built-in 8MB Flash and 8MB PSRAM.
It provides 11 GPIO pins, an onboard battery power interface, and can be directly connected to an external 3.7V lithium battery for power supply.
With an efficient built-in PMIC and multi-level power control design, it supports power input and output control, as well as status monitoring for input voltage u batterija voltage. It supports external low-power wake-up. After the main controller shuts down and enters low-power sleep mode, it can be triggered to wake up via an external PMIC wake-up IO. The module features an onboard user button and a programmable RGB LED. With 2.54mm standard-pitch half-hole solder pads, it can be integrated into your applications through SMT, DIP, or other methods, helping developers quickly build IoT applications.
Speċifikazzjonijiet
Bidu malajr
Preparazzjoni
- Żur l-Arduino uffiċjali websit u installa l-Arduino IDE
https://www.arduino.cc/en/Main/Software - Żid il-Maniġer tal-Bord li ġej URL biex File → Preferenzi → Maniġer tal-Bordijiet Addizzjonali URLs:
https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
- Iftaħ il-Bordijiet Manager, fittex għal “ESP32”, u kklikkja fuq installa.
- After installation, select the board “ESP32S3 Dev Module”.
- Configure the following options. USB CDC On Boot: “Enabled”, PSRAM： “OPI PSRAM”, USB Mode: “Hardware CDC and JTAG"
Wi-Fi Scan
- Agħżel l-exampil-programm “Examples” → “WiFi” → “WiFiScan”, agħżel il-port li jikkorrispondi mat-tagħmir tiegħek, u kklikkja l-buttuna kumpila u upload fir-rokna ta’ fuq tax-xellug.
- Wara li t-tlugħ ikun komplut, iftaħ is-Serial Monitor biex view Informazzjoni dwar l-iskennjar tal-Wi-Fi.
BLE Scan
- Agħżel l-exampil-programm “Examples” → “BLE” → “Scan”, agħżel il-port li jikkorrispondi mat-tagħmir tiegħek, u kklikkja l-buttuna compile and upload fir-rokna ta’ fuq tax-xellug.
- Wara li t-tlugħ ikun komplut, iftaħ is-Serial Monitor biex view Informazzjoni dwar l-iskennjar BLE.
Twissija tal-FCC
Attenzjoni FCC:
Kwalunkwe Tibdil jew modifika mhux approvata espressament mill-parti responsabbli għall-konformità tista' tħassar l-awtorità tal-utent biex iħaddem it-tagħmir.
Dan l-apparat jikkonforma mal-parti 15 tar-Regoli tal-FCC. It-tħaddim huwa soġġett għaż-żewġ kundizzjonijiet li ġejjin:
- This device may not cause harmful interference, andThiss device must accept any interference received, including interference that may cause undesired operation.
NOTA IMPORTANTI:
Nota: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use,s and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Orjenta mill-ġdid jew iċċaqlaq l-antenna li tirċievi.
- Żid is-separazzjoni bejn it-tagħmir u r-riċevitur.
- Qabbad it-tagħmir fi żbokk fuq ċirkwit differenti minn dak li miegħu huwa konness ir-riċevitur.
- Ikkonsulta lin-negozjant jew tekniku tar-radju/TV b'esperjenza għall-għajnuna.
Dikjarazzjoni ta' Espożizzjoni għar-Radjazzjoni FCC:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated wita h minimum distance of 20cm between the radiator & your body.
Mistoqsijiet Frekwenti
Q: Can I power the Stamp-S3Bat using a different voltage batterija?
A: It is recommended to use a 3.7V lithium battery as the input power source for the Stamp-S3Bat to ensure optimal performance and compatibility.
Q: How many GPIO pins does Stamp-S3Bat provide?
A: Stamp-S3Bat provides a total of 11 GPIO pins for connecting external devices and sensors.
Q: What is the operating temperature range of Stamp-S3Bat?
A: The operating temperature range of Stamp-S3Bat is not specified in the user manual. It is advisable to operate within normal room temperature conditions for best results.
Dokumenti / Riżorsi
 |
Triq M5STACKamp-S3Bat Embedded Core Module [pdfGwida għall-Utent Stamp-S3Bat, Stamp-S3Bat Embedded Core Module, Embedded Core Module, Core Module |