LTECH KMS1 Switch Module

Introduzzjoni tal-Prodott

• Fully supports major smart home ecosystems including Apple Home, SmartThings, Google Assistant, and Amazon, enabling unified management across platforms.
• Built-in Thread module, compatible with the Matter protocol, supports Siri, Google, and Alexa voice control.
• Supports OTA firmware updates to continuously receive the latest features and security patches, ensuring long-term device stability.
• Parameter settings for switch type and power-on status can be completed via the NFC Lighting App.
• Reserved mechanical switch/reset switch interface accommodates both traditional operating habits and smart scenario requirements.

Speċifikazzjonijiet Tekniċi

Mudell	KMS1
Tip bla fili	Materja fuq Thread
Aqleb kanal	1CH
Vol operattivtage	100-240V~, 50/60Hz
Parametri massimi tat-tagħbija tar-relay	Resistive load: 1000W@230Vac, 500W@110Vac Capacitive load: 400W@230Vac, 200W@110Vac
Kurrent ta' żieda fir-relay	70A@10ms
Temperatura tax-xogħol	-25°C ~ 50°C
Daqs tal-prodott	L45×W45.5×H20.5(mm)
Piż tal-prodott	38g
Standards	UL 8750, EN 61347-2-13:2014+A1:2017, EN 61347-1:2015+A1:2021, EN 62493:2015/A1:2022

Stampi tal-Prodott

DIMENSJONI

• Unità: mm
• Dimensjonijiet: 45 x 45.5 x 20.5

Dijagramma tal-Wiring

1.  Dijagramma tal-Wajers tas-Swiċċ Mekkaniku
   Includes connections for load, line (L), and neutral (N).
2.  Dijagramma tal-Wajers tas-Swiċċ Push
   Includes connections for load, line (L), and neutral (N).

Uża l-APP tad-Dawl NFC
Scan the QR code with your mobile phone and install the APP as prompted. Compatible with iOS 13 or above and Android NFC-enabled models.

Read the Device
Click “Read/Write LED driver” in the APP [home page], place the sensing area of the phone near the NFC identification point of the driver, and read the device parameters.

Edit Parametri
Click “Parameter Management” to select the switch type. When selecting a reset switch, you can configure the device’s power-on state function.

Add to Matter Platform Instructions

1. This device supports control via major smart home platforms, including Apple Home, Amazon Alexa, Google Home, Smart Things, and others.
2. To connect Matter over Thread devices, prepare a Matter hub supporting Thread border router functionality from major platforms.

Mudelli Kompatibbli

Setup Eżample

• This guide uses Apple Home as an example. Prepare an iPhone (iOS 16.2 or later) or iPad (iPadOS 16.2 or later) with the latest firmware, along with an Apple HomePod mini also running the latest firmware. Connect your iPhone or iPad to your home Wi-Fi network, launch the Apple Home app, and follow Apple’s instructions to set up the HomePod mini.
• For iPhone models 15 and above, no Matter hub is required; they can be added directly.

Żid Aċċessorji

• Open the Apple Home app and tap “Add or Scan Accessories.” Add the device to Apple Home by scanning the QR code sticker on the device.
• *You can also activate service via NFC: Simply hold your iPhone 16 or later model near the device’s NFC sensor area to be recognized and activated.

Apparat ta 'Kontroll
After successfully adding the device to Apple Home, tap the device icon to turn it on or off.

Karatteristiċi Avvanzati

Supports creating groups, scenes, and automations, as well as remote control and scheduled control. Devices can also be controlled via Siri voice commands.

Irrestawra l-Settings tal-Fabbrika

Reset Button Reset
Press and hold the reset button for 15 seconds until the indicator light flashes red rapidly, then release. Within 3 seconds, press the reset button three times briefly. The red light will then switch to slow flashing, indicating the device has begun restoring factory settings. When the indicator light flashes blue rapidly, the restoration is complete.

Irrisettja Power-on
Fil-każ ta' qawwa outage, use the switch to power on the device for 15 seconds before powering it off. Repeat this power cycle six times consecutively (each cycle consisting of 2 seconds on and 5 seconds off). After the seventh power cycle, the load lamp will flash three times, indicating a successful reset to factory settings.

Attenzjoni

• L-installazzjoni u l-ikkummissjonar tal-prodott għandhom isiru minn professjonist kwalifikat.
• Our company products are not waterproof or lightning-proof (special models excepted). Please avoid the sun and rain. When installed outdoors, please ensure they are mounted in a waterproof enclosure or in an area equipped with lightning protection devices.
• Dissipazzjoni tajba tas-sħana se jtawwal il-ħajja tax-xogħol tal-prodotti. Jekk jogħġbok żgura ventilazzjoni tajba.
• Jekk jogħġbok iċċekkja jekk il-vol tax-xogħoltage użat jikkonforma mar-rekwiżiti tal-parametri tal-prodotti.
• Id-dijametru tal-wajer użat għandu jkun kapaċi jgħabbi l-attrezzaturi tad-dawl li tikkonnettja u jiżgura l-wajering sod.
• Qabel ma tixgħel il-prodotti, jekk jogħġbok kun żgur li l-wajers kollha huma korretti f'każ ta 'konnessjoni mhux korretta li tikkawża ħsara lill-attrezzaturi tad-dawl.
• Jekk isseħħ xi ħsara, jekk jogħġbok tippruvax tirranġa l-prodotti waħdek. Jekk għandek xi mistoqsija, jekk jogħġbok ikkuntattja lill-fornituri tiegħek.

Ftehim ta 'Garanzija

Perjodi ta' garanzija mid-data tal-kunsinna: 2 snin. Servizzi ta’ tiswija jew sostituzzjoni b’xejn għal problemi ta’ kwalità huma pprovduti fi ħdan perjodi ta’ garanzija.

Esklużjonijiet ta' Garanzija

• Lil hinn mill-perjodi ta' garanzija.
• Kwalunkwe ħsara artifiċjali kkawżata minn voltage, tagħbija żejda, jew operazzjonijiet mhux xierqa.
• Prodotti bi ħsara fiżika severa.
• Ħsara kkawżata minn diżastri naturali u force majeure.

1. It-tikketti tal-garanzija u l-barcodes ġew imħassra.
2. No contract signed by our company.

Dokumenti / Riżorsi

LTECH KMS1 Switch Module [pdfManwal tas-Sid KMS1 Switch Module, KMS1, Switch Module, Module

Referenzi

• Manwal għall-Utent