Keeson RC309A Remote Control User Manual

Keeson RC309A Remote Control

Speċifikazzjonijiet

• Isem tal-Prodott: KONTROLL mill-bogħod
• Mudell: RC309A
• Input: 2 x batteriji AAA 1.5V
• Manifattur: Keeson Technology Corporation Limited
• Pajjiż tal-manifattura: Iċ-Ċina

Istruzzjonijiet għall-Użu

Figure 1 illustrates the buttons on the remote control.

1. Ras 'il fuq
   Press and hold the HEAD UP button of the remote, the head actuator moves out, stop when released.
2. Ras 'l isfel
   Press and hold the HEAD DC NNN button of the remote, the head actuator moves in, and stops when released.
3. Sieq 'il fuq
   Press and hold the FOOT UP button of the remote, the foot actuator moves out, stop when released.
4. Sieq 'l isfel
   Press and hold the FOOT button of the remote, the foot actuator moves in, stop when released.
5.  Ċatt
   lick FLAT button, the bed goes flat. Stop when you click any button during the process of going flat.
6. Ras tal-massaġġi 
   lick MASSAGE HEAD button, head massage motor switches massage intensity, massage intensity switches among 0-1-2;
7. buttuna ZG
   Click the ZG button, the actuator moves to the ZG position, stop when clicking any button during the movement.
8. Memory Favorite position
   licking once will move the app to the Favorite position; long-pressing to memorize the position. The backlight will flash twice, and releasing the button will continue the flashing.
9. Lock
   Press and hold the child lock button until the red light flashes twice, indicating that the child lock is successfully engaged. During the locking process, pressing any button will cause the red light to flash for 2 seconds, indicating that the lock is engaged.

Informazzjoni dwar il-prodott

• Product Name: REMOTE CONTROL
• Mudell: RC309B
• Input: 2 x Battery AAA 1.5V
• Manifattur: Keeson Technology Corporation Limited
• Pajjiż tal-manifattura: iċ-Ċina

Twissija tal-FCC:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can adiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Orjenta mill-ġdid jew iċċaqlaq l-antenna li tirċievi.
• Żid is-separazzjoni bejn it-tagħmir u r-riċevitur.
• Qabbad it-tagħmir fi żbokk fuq ċirkwit differenti minn dak li miegħu huwa mqabbad ir-riċevitur.
• Ikkonsulta lin-negozjant jew tekniku tar-radju-TV b'esperjenza għall-għajnuna.

Kwalunkwe Tibdil jew modifika mhux approvata espressament mill-parti responsabbli għall-konformità tista' tħassar l-awtorità tal-utent biex iħaddem it-tagħmir. Dan l-apparat jikkonforma mal-parti 15 tar-Regoli tal-FCC. It-tħaddim huwa soġġett għaż-żewġ kundizzjonijiet li ġejjin:

1. Dan l-apparat jista' ma jikkawżax interferenza ta' ħsara,
2. Dan l-apparat għandu jaċċetta kwalunkwe interferenza riċevuta, inkluża interferenza li tista 'tikkawża tħaddim mhux mixtieq.

Informazzjoni dwar l-Espożizzjoni RF

L-apparat ġie evalwat biex jissodisfa r-rekwiżit ġenerali ta' espożizzjoni RF. L-apparat jista 'jintuża f'kundizzjoni ta' espożizzjoni mingħajr restrizzjoni.

ISED RSS Twissija:

This device complies with Innovation, Science and Economic Development Canada licence, exemplifying RSS standard(s). Operation is subject to the following two conditions:

• Dan l-apparat ma jistax jikkawża interferenza.
• This device must accept any interference, including interference that mav cause undesired operation of the device.

Issolvi l-problemi

If the remote control is not functioning as expected:

• Iċċekkja Batteriji: Ensure that two AAA 1.5V batteries are correctly inserted and have sufficient charge.
• Lock tat-tfal: If the remote is unresponsive and the red light flashes for 2 seconds when a button is pressed, the child lock may be engaged. Refer to section 1.7 to disengage the child lock.
• Interferenza: This device complies with FCC rules regarding interference. If you experience unexpected operation, it might be due to external interference. Ensure there are no strong radio frequency sources nearby.

FAQs

Q: What type of batteries does the RC309A remote control use?
A: The remote control requires 2 x AAA 1.5V batteries.

Q: How do I stop the bed from moving once I’ve pressed a position button?
A: For continuous movements like Head Up/Down or Foot Up/Down, release the button to stop. For preset positions like Flat or ZG, clicking any button during the movement will stop the process.

Q: What does it mean if the red light flashes for 2 seconds when I press a button?
A: This indicates that the child lock feature is currently engaged. You will need to disengage the child lock to use the remote’s functions (refer to section 1.7).

M: Nista' nimmodifika l-kontroll remot?
A: Any changes or modifications not expressly approved by the manufacturer could void your authority to operate the equipment and are not recommended.