Heltec T114 Mesh Node Owner’s Manual

Heltec T114 Mesh Node

Speċifikazzjonijiet

• Product Name: Mesh Node T114
• Mudell: T114
• Batch/Serial Number: 1005007917409559
• MCU: nRF52840 (Bluetooth)
• LoRa Chipset: SX1262
• Display: 1.14 inch TFT-LCD (Optional) – 135(H)RGB x 240(V)
  dots, up to 262k colors
• Interfaces: 2*1.25mm LiPo connector, 2*1.25mm Solar panel
  connector, 8*1.25mm GNSS module connector
• Operating Conditions: -20°C to 70°C, 90% RH
  (Mhux kondensazzjoni)

Istruzzjonijiet għall-Użu tal-Prodott

Sigurtà u Twissijiet:

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

• Do not plug or unplug chips, modules, or wires when the device is powered on.
• Handle with care; do not press, drop, or touch exposed pins with metal tools.
• Place in a well-ventilated and dry area; keep away from heat sources and direct sunlight.

Struzzjonijiet għall-Użu

Mandatory steps for using the Mesh Node T114:

1. Kun żgur li l-apparat ikun mitfi qabel ma tagħmel xi konnessjonijiet.
2. Connect necessary peripherals using the provided interfaces.
3. If using the optional TFT-LCD display, follow the display setup instructions.
4. Operate the device within the specified temperature and humidity range.
5. Refer to the provided Arduino development frameworks and libraries for programming guidance.

Informazzjoni dwar il-Prodott

• Product Name: [Mesh Node T114]
• Model: [T114]
• Batch/Serial Number: [1005007917409559]

Informazzjoni ta' Konformità

Spjegazzjoni tas-simbolu
Indicates that the product complies with the essential requirements of the relevant European directives and serves as evidence that the product has passed the corresponding conformity assessment procedures and/or manufacturer’s declaration of conformity

Informazzjoni Importanti dwar is-Sigurtà

Sigurtà u Twissijiet

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

1. Warning: Keep the device and its cord out of reach of children under 3 years old.
2. Keep away from children unless supervised by an adult.
3. Do not use this product for purposes other than its intended use (for R&D and learning only).
4. Inspect the product before each use; do not use if damaged (e.g., broken cord, damaged interface).
5. Follow installation and operation guidelines to avoid injury and device damage.
6. This is an electrical product; do not expose to water or moisture.
7. Use a qualified power adapter matching the device’s rated specifications; do not reverse positiveand n egative poles.
8. Do not plug or unplug chips, modules or wires when the device is powered on.
9. Handle with care; do not press, drop or touch exposed pins with metal tools.
10. Place in a well-ventilated and dry area; keep away from heat sources and direct sunlight.

Struzzjonijiet għall-Użu

Mesh Node T114Verżjoni tad-Dokument

Verżjoni	Ħin	Deskrizzjoni	Rimarka
Rev 1.0	2024-5-16	Verżjoni preliminari	Richard
Rev 2.0	2024-10-18	V2	Richard

Avviż dwar id-drittijiet tal-awtur
Il-kontenut kollu fil- files huma protetti mil-liġi tad-drittijiet tal-awtur, u d-drittijiet tal-awtur kollha huma riżervati minn Chengdu Heltec Automation Technology Co., Ltd. (minn hawn 'il quddiem imsejħa Heltec). Mingħajr permess bil-miktub, l-użu kummerċjali kollu tal- files minn Heltec huma pprojbiti, bħal kopja, tqassam, tirriproduċi l files, etc., but non-commercial purposes, downloading or printing by individuals is welcome.

Ċaħda
Chengdu Heltec Automation Technology Co., Ltd tirriżerva d-dritt li tibdel, timmodifika jew ittejjeb id-dokument u l-prodott deskritt hawn. Il-kontenut tiegħu huwa soġġett għal bidla mingħajr avviż. Dawn l-istruzzjonijiet huma maħsuba biex tużah.

Deskrizzjoni

Fuqview
Mesh Node T114 is a development board based on nRF52840 and SX1262, supports LoRa communication and Bluetooth 5.0, and provides a variety of power interfaces (5V USB, lithium battery and solar panel), optional 1.14 inch TFT display and GPS module as accessories.
Mesh Node T114 has powerful long-distance communication capabilities, scalability, and low power design, which make it excellent in a wide range of application scenarios such as smart cities, agricultural monitoring, logistics tracking, etc. With Heltec nRF52 development environment and libraries , you can use it for
LoRa/LoRaWAN development work, as well as to run some open source projects, such as Meshtastic.
Mesh Node T114 are available in 2 product variants①:

Nru.	Mudell	Deskrizzjoni
1	HT-n5262-LF	Frekwenza LoRa tax-xogħol ta' 470 ~ 510MHz, użata għaċ-Ċina   medda LPW tal-kontinent (CN470).
2	HT-n5262-HF	For EU868, IN865, US915, AU915, AS923, KR920 and other LPW networks with operating frequencies between 863~928MHz.

Karatteristiċi tal-Prodott

• MCU nRF52840 (Bluetooth), chipset LoRa SX1262.
• Konsum baxx ta 'enerġija, 11 uA fi rqad fil-fond.
• Funzjoni ta 'wiri qawwija (mhux obbligatorja), display TFT-LCD ta' 1.14 pulzier abbord fih 135(H)RGB x240(V) tikek u jista 'juri sa 262k kuluri.
• Interface USB tat-Tip-C b'vol kompluttage regolatur, protezzjoni ESD, protezzjoni ta 'short circuit, shielding RF, u miżuri oħra ta' protezzjoni.
• Interfaces Diversi (konnettur LiPo 2 * 1.25mm, konnettur tal-pannelli solari 2 * 1.25mm, konnettur tal-modulu GNSS 8 * 1.25mm) li jżidu ħafna l-estensibbiltà tal-bord.
• Kondizzjoni ta 'tħaddim: -20 ~ 70 ℃, 90% RH (L-ebda kondensazzjoni).
• Kompatibbli ma 'Arduino, u nipprovdu oqfsa u libreriji ta' żvilupp Arduino.

Definizzjoni tal-Pin
About SPI, I2C, UART, PWM, QPSI, I2S, PDM, QDEC: Each IO pin is preconfigured with IO_MUX functionality, which means you can use any GPIO as peripheral pins. You just need to define these pins in your code.
However, it’s important to note that once a pin is used, it may affect other functions associated with that pin. For information, please refer to the Schemaic diagram.

Pin Pin

Definizzjoni tal-Pin

p1                                                                                       p2

Isem	Tip	Deskrizzjoni		Isem	Tip	Deskrizzjoni
5V	P	Qawwa 5V.		Ve	P	Qawwa 3V3.
GND	P	Art.		GND	P	Art.
3V3	P	Qawwa 3.3V.		0.08	I/O	GPIO8.
GND	P	Art.		0.07	I/O	GPIO7.
0.13	I/O	GPIO13.		1.12	I/O	GPIO44.

0.16	I/O	GPIO16.		1.14	I/O	GPIO46.
RST	I/O	RESET.		0.05	I/O	GPIO5.
1.01	I/O	GPIO33.		1.15	I/O	GPIO47.
SWD	I/O	SWDIO.		1.13	I/O	GPIO45.
SWC	I/O	SWCLK.		0.31	I/O	GPIO31.
SWO	I/O	SWO.		0.29	I/O	GPIO29.
0.09	I/O	GPIO9, UART1_RX.		0.30	I/O	GPIO30.
0.10	I/O	GPIO10, UART1_TX.		0.28	I/O	GPIO28.

Speċifikazzjonijiet

Parametri	Deskrizzjoni
MCU	nRF52840
LoRa Chipset	SX1262
Memorja	ROM 1M; 256KB SRAM
Bluetooth	Bluetooth 5, malji Bluetooth, BLE.
Temperatura tal-ħażna	-30 ~ 80 ℃
Temperatura operattiva	-20 ~ 70 ℃
Umdità Operattiva	90% (L-ebda kondensazzjoni)
Provvista tal-Enerġija	3 ~ 5.5V (USB), 3 ~ 4.2 (batterija)
Modulu tal-Wiri	LH114T-IF03
Daqs tal-Iskrin	1.14 Pulzier
Riżoluzzjoni tal-Wiri	135RGB x 240

Żona Attiva	22.7 mm(H) × 42.72(V) mm
Wiri Kuluri	262K
Riżorsi tal-Hardware	USB 2.0, 2*RGB, 2*Button, 4*SPI, 2*TWI, 2*UART, 4*PWM, QPSI, I2S, PDM, QDEC Etc.
Interface	Type-C USB, 2*1.25 lithium battery connector, 2*1.25 solar panel connector, LoRa ANT (IPEX1.0), 8*1.25 GPS module connector, 2*13*2.54 Header Pin
Dimensjonijiet	50.80mm x 22.86mm
Kurrent Operattiv	1A

Konsum tal-Enerġija

Modalità	Kundizzjoni	Konsum (Battry@3.7V)
		470MHz	868MHz	915MHz
LoRa_TX	5dBm		83mA	93mA
	10dBm		108mA	122mA
	15dBm		136mA	151mA
	20dBm		157mA	164mA
BT	UART	93mA
	Skennja	132mA
Irqad		11uA
Kurrent Operattiv		1A

LoRa RF Karatteristiċi

Trasmetti l-Qawwa

470 ~ 510	21 ± 1
863 ~ 870	21 ± 1
902 ~ 928	21 ± 1

Sensittività Riċevitur

 The following table gives the sensitivity level typically

Wisa' ta' Faxxa tas-Sinjal/[KHz]	Fattur ta' Tixrid	Sensittività/[dBm]
125	SF12	-135
125	SF10	-130
125	SF7	-124

Frekwenzi ta' Operazzjoni
Mesh Node T114 supports LoRaWAN frequency channels and models corresponding table.

Reġjun	Frekwenza (MHz)	Mudell
EU433	433.175 ~ 434.665	HT-n5262-LF
CN470	470 ~ 510	HT-n5262-LF
IN868	865 ~ 867	HT-n5262-HF
EU868	863 ~ 870	HT-n5262-HF
US915	902 ~ 928	HT-n5262-HF
AU915	915 ~ 928	HT-n5262-HF
KR920	920 ~ 923	HT-n5262-HF
AS923	920 ~ 925	HT-n5262-HF

Dimensjonijiet Fiżiċi

 

Riżorsa

Żviluppa qafas u lib

• Heltec nRF52 qafas u Lib

Server ta' rakkomandazzjoni

• Server tat-test Heltec LoRaWAN ibbażat fuq TTS V3
• Pjattaforma IoT SnapEmu

Dokumenti

• Mesh Node T114 Manual Document

Dijagramma Skematika

• V1Dijagramma Skematika
• V2Dijagramma Skematika

Riżorsi Relatati

• Skeda tad-dejta TFT-LCD

Informazzjoni ta' Kuntatt ta' Heltec

• Heltec Automation Technology Co., Ltd
• https://heltec.org

FAQs

Q: Can I use the Mesh Node T114 with other LPW networks?

• A: Yes, the Mesh Node T114 supports various LPW networks with operating frequencies between 863~928MHz.

Q: What is the power consumption of the Mesh Node T114 in deep sleep?

• A: The device consumes only 11 uA in deep sleep mode, ensuring low power usage.