BN-LINK SU101D Timer Switch Instructions

BN-LINK SU101D Timer Switch

SPEĊIFIKAZZJONI TEKNIKA

• 18 ON/OFF kuljum
• With ON/OFF/Timing shift function With Ni-MH recharging battery
• Min. Setting time: 1 minute Max. Setting time: 7 days
• Provvista voltage: 125V-,60Hz
• Klassifikazzjoni tal-kuntatt: 15A/1875W Reżistiv
• 10A/1250WTungstenu, 10A/1250W Ballest, 1/2 HP, TV-5
• Taqbiżx il-klassifikazzjonijiet elettriċi
• Temperatura operattiva: 5F 122F (-15€ 50C)
• Temperatura tal-ħażna: -4F 140F (-20C 60C)
• Klassi ta 'insulazzjoni: II
• Klassi ta 'protezzjoni: IP20

Importanti: induttiv (tagħbija tal-bidu) għandu dejjem jiġi kkalkulat speċjalment meta tikkontrolla d-dawl (minħabba tagħbijiet induttivi varjabbli). Jekk din it-tagħbija taqbeż it-8 Amps allura huwa imperattiv li jintuża kuntrattur.

GWIDA TA' MALAJR TAL-PRODOTT

Karatteristiċi

1. Il-buttuna ta 'override manwali tippermetti li tixgħel jew itfi t-tajmer fi kwalunkwe ħin.
2. Skrin LCD kbir faċli biex jinqara b'displej tal-arloġġ.
3. Up to 18 ON events and 18 OFF events daily
4. L-issettjar tas-sigurtà bl-addoċċ jippermetti li jiġu posposti rispettivament il-ħinijiet ON u OFF b'0-30 minuta biex tinħoloq ħarsa "lid-in".
5. Ixgħel jew itfi DTS b'buttuna waħda sempliċi.

TWISSIJA
To prevent the risk of electric shock, cut off the power supply before installation. Always have a qualified electrician install this product.

INSTALLAZZJONI

• PASS 1: CUT OFF THE POWER SUPPLY TO THE IN-WALL WIRING BOX.
• PASS 2: REMOVE THE EXISTING DEVICE IF ANY.
• PASS 3: INSTALLA L-TIMER.

INSTALLAZZJONI SINGLE-POLE

Nota

1. Biex tissostitwixxi swiċċ eżistenti, jekk jogħġbok kun żgur li l-wajer newtrali huwa disponibbli fil-kaxxa tal-ħajt.
2. Qabel il-wiring, jekk jogħġbok aqta 'l-enerġija fil-breaker u aqleb it-tajmer għal MANUAL OFF. (Jekk jogħġbok irreferi għall-kapitolu TIBDIL BEJN ŻEWĠ MODI TA' OPERAZZJONI)

Wiring:

• a. Wajer ta 'l-art: Qabbad il-wajer ta' l-art fil-kaxxa tal-ħajt (jew il-kamin ta 'l-ert) mal-wajer AĦDAR tat-tajmer.
• b. Neutral wire: Connect the Neutral wire in the wall box (from the breaker) to the WHITE wire of the timer. (The Neutral wire from the breaker should also be connected to the load’s neutral wire.)
• c. Hotwire: Qabbad il-wajer sħun fil-kaxxa tal-ħajt (mill-breaker) mal-wajer ISWED tat-tajmer.
• d. Wajer tat-tagħbija: Qabbad il-wajer sħun tat-tagħbija (minn tagħbija bħal dawl) mal-wajer AĦMAR tat-tajmer.
• e. Uża skorfina tal-wajer biex iddawwar il-wajer BLUE għas-sigurtà.

INSTALLAZZJONI 3-MOD

Installazzjoni konvenzjonali 3-way

Installazzjoni tal-timer-on-the-line-side

1. Biex tissostitwixxi swiċċ eżistenti, jekk jogħġbok kun żgur li l-wajer newtrali huwa disponibbli fil-kaxxa tal-ħajt.
2. Qabel il-wiring, jekk jogħġbok aqta 'l-enerġija fil-breaker u aqleb it-tajmer għal MANUAL OFF. (Jekk jogħġbok irreferi għall-kapitolu TIBDIL BEJN ŻEWĠ MODI TA' OPERAZZJONI)
3. Wiring:

Pass 1: Wring in-naħa tal-LINJA

• a. Wajer ta 'l-art: Qabbad il-wajer ta' l-art fil-kaxxa tal-ħajt (jew il-kamin ta 'l-ert) mal-wajer AĦDAR tat-tajmer.
• b. Wajer newtrali: Qabbad il-wajer newtrali fil-kaxxa tal-ħajt (mill-breaker) mal-wajer ABJAD tat-tajmer. (Il-wajer newtrali mill-breaker għandu wkoll ikun imqabbad mal-wajer newtrali tat-tagħbija)
• c. Hotwire: Qabbad il-Hotwire fil-kaxxa tal-ħajt (mill-breaker) mal-wajer ISWED tat-tajmer.
• d. Vjaġġaturi:
  • Vjaġġatur 1: Qabbad Vjaġġatur 1 (min-naħa tat-tagħbija) mal-wajer AĦMAR tat-tajmer.
  • Vjaġġatur 2: Qabbad Vjaġġatur 2 (min-naħa tat-tagħbija) mal-wajer BLUE tat-tajmer.

Pass 2: Wring in-naħa TAGĦBIJA

• Vjaġġatur 1: Qabbad il-Vjaġġatur 1 (mill-arloġġ) u l-wajer sħun tat-tagħbija mat-terminal KOMUNI (ġeneralment iswed jew ikkulurit tar-ram) tas-swiċċ bi 3 direzzjonijiet.
• Vjaġġatur 2: Qabbad il-Vjaġġatur 2 (mill-tajmer) ma' kwalunkwe terminal (ġeneralment kulur ir-ram) tas-swiċċ bi 3 direzzjonijiet.

Installazzjoni ta 'timer-on-the-load-side

Nota

1. Biex tissostitwixxi swiċċ eżistenti, jekk jogħġbok kun żgur li l-wajer newtrali huwa disponibbli fil-kaxxa tal-ħajt.
2. Qabel il-wiring, jekk jogħġbok aqta 'l-enerġija fil-breaker u aqleb it-tajmer għal MANUAL OFF. (Jekk jogħġbok irreferi għall-kapitolu TIBDIL BEJN ŻEWĠ MODI TA' OPERAZZJONI)
3. Wiring:

Pass 1: Wring in-naħa tal-LINJA

• HOT wire: Connect the Hotwire in the wall box (from breaker) to Traveler 1 (from the timer) and the jumper, then connect the jumper to the COMMON terminal (usually black or copper colored) of the 3-way switch.
• Vjaġġatur 2: Connect Traveler 2 (from the timer) to either terminal (usually brass colored) of the 3-way switch.

Pass 2: Wring in-naħa TAGĦBIJA/TIMER

• a. Wajer ta 'l-art: Qabbad il-wajer ta' l-art fil-kaxxa tal-ħajt (jew il-kamin ta 'l-ert) mal-wajer AĦDAR tat-tajmer.
• b. Wajer newtrali: Qabbad il-wajer newtrali fil-kaxxa tal-ħajt (mill-breaker) mal-wajer ABJAD tat-tajmer. (Il-wajer newtrali mill-breaker għandu wkoll ikun imqabbad mal-wajer newtrali tat-tagħbija)
• c. Load Hotwire: Connect the Load’s Hotwire in the wall box (from Load such as Light) to the RED wire of the timer.
• d. Vjaġġaturi:
  • Vjaġġatur 1: Qabbad Vjaġġatur 1 (Min-naħa tal-LINJA) mal-wajer ISWED tat-tajmer.
  • Vjaġġatur 2: Qabbad il-Vjaġġatur 2 (Min-naħa tal-LINJA) mal-wajer BLUE tat-tajmer.

INSTALLAZZJONI 4-MOD

Nota

1. To replace an existing switch, please make sure that the neutral wire is available in the wall box. Also, make sure that 5 travelers are available between the wall boxes and mark each wire (such as “HOT WIRE, NEUTRAL WIRE, TRAVELER 1, TRAVELER 2 ..) for identification first,
2. Before wiring, please cut OFF the power at the breaker and switch the timer to MANUAL OFF. (Please refer to the chapter SWITCHING BETWEEN TWO OPERATION MODES)
3. Wiring:

Pass 1: Wring in-naħa LIND/TIMER

• a. Wajer ta 'l-art: Qabbad il-wajer ta' l-art fil-kaxxa tal-ħajt (jew il-kamin ta 'l-ert) mal-wajer AĦDAR tat-tajmer.
• b. Wajer newtrali: Qabbad il-wajer newtrali fil-kaxxa tal-ħajt (mill-breaker) mal-wajer ABJAD tat-tajmer. (Il-wajer newtrali mill-breaker għandu wkoll ikun imqabbad mal-wajer newtrali tat-tagħbija)
• c. Hotwire: Qabbad il-Hotwire fil-kaxxa tal-ħajt (mill-breaker) mal-wajer ISWED tat-tajmer.
• d. Vjaġġaturi:
  • Vjaġġatur 1: Qabbad Vjaġġatur 1 (mill-kaxxa tal-iswiċċ b'4 direzzjonijiet) mal-wajer BLU tat-tajmer.
  • Vjaġġatur 2: Qabbad Vjaġġatur 2 (mill-kaxxa tal-iswiċċ b'4 direzzjonijiet) mal-wajer AĦMAR tat-tajmer.

Pass 2: Wring l-iswiċċ 4-way

• a. Traveler 1: Connect Traveler 1(from the LINE side) to any of the terminals of the 4-way switch.
• b. Vjaġġatur 2: Qabbad il-Vjaġġatur 2 (min-naħa tal-LINJA) mal-Vjaġġatur 5 (min-naħa tat-TAGĦBIJA).
• c. Traveler 3: Connect Traveler 3(from the LOAD side) to one of the terminals at another end of the 4-way switch.
• d. Traveler 4: Connect Traveler 4(from the LOAD side) to another terminal (at the same end as Traveler 3) of the 4-way switch.

ATTENZJONI: Traveler 1 can’t be connected to the terminal, which is at the same end as Traveler 3 or Traveler 4. Traveler 3 and Traveler 4 to the 3-way switch fin the LOAD side) have to be connected at the same end.

Pass 3: Wiring in-naħa TAGĦBIJA

1. a. Traveler 5: Use a wire nut to connect together the load’s hot wire, a jumper, and Traveler 5(from the 4-way switch box), Then connect the jumper to the COMMON terminal (usually black or copper colored) of the 3-way switch on the LOAD side.
2. b. Vjaġġatur 3: Qabbad il-Vjaġġatur 3 (min-naħa tal-kaxxa 4-way) għal kwalunkwe terminal (ġeneralment kulur tar-ram) tal-iswiċċ 3-way fuq in-naħa TAGĦBIJA.
3. c. Vjaġġatur 4: Qabbad il-Vjaġġatur 4 (min-naħa tal-kaxxa 4-way) mat-tielet terminal (ġeneralment kulur ir-ram) tas-swiċċ 3-way fuq in-naħa TAGĦBIJA.
   

Nota

1. To replace an existing switch, please make sure that the neutral wire is available in the wall box. Also make sure that 7 travelers are available between the wall boxes and mark each wire (such as “HOT WIRE, NEUTRAL WIRE, TRAVELER 1, TRAVELER 2 …) for identification first.
2. Qabel il-wiring, jekk jogħġbok aqta 'l-enerġija fil-breaker u aqleb it-tajmer għal MANUAL OFF. (Jekk jogħġbok irreferi għall-kapitolu TIBDIL BEJN ŻEWĠ MODI TA' OPERAZZJONI)
3. Wiring:

Pass 1: Wiring in-naħa tal-LINJA

• a. HOT wire: Use a wire nut to connect together the HOT wire (from breaker), a jumper, and Traveler 5(from the 4-way switch box), then connect the jumper to the COMMON terminal (usually black or copper colored) of the 3-way switch on the LINE side.
• b. Vjaġġatur 1: Qabbad il-Vjaġġatur 1 (mill-kaxxa tal-iswiċċ 4-Way/Timer) għal kwalunkwe terminal (ġeneralment kulur ir-ram) tal-iswiċċ 3-way fuq in-naħa tal-LINJA.
• c. Vjaġġatur 2: Qabbad il-Vjaġġatur 2 (mill-kaxxa tal-iswiċċ 4-Way/Timer) mat-tielet terminal (ġeneralment kulur ir-ram) tal-iswiċċ 3-way fuq in-naħa tal-LINJA.

Pass 2: Wiring tas-swiċċ 4-way/TIMER

• a. Wajer ta 'l-art: Qabbad il-wajer ta' l-art fil-kaxxa tal-ħajt (jew il-kamin ta 'l-ert) mal-wajer AĦDAR tat-tajmer.
• b. Wajer newtrali: Qabbad il-wajer newtrali fil-kaxxa tal-ħajt (mill-breaker) mal-wajer ABJAD tat-tajmer. (Il-wajer newtrali mill-breaker għandu wkoll ikun imqabbad mal-wajer newtrali tat-tagħbija)
• c. Vjaġġaturi:
  • Vjaġġatur 1: Connect Traveler 1 (from the LINE side) to Traveler 4 (from the LOAD side).
  • Vjaġġatur 2: Connect Traveler 2 (from the LINE side) to Traveler 3 (from the LOAD side).
  • Vjaġġatur 5: Qabbad Traveler 5 (min-naħa tal-LINJA) mal-wajer ISWED tat-tajmer.
  • Vjaġġatur 6: Qabbad Traveler 6 (min-naħa TAGĦBIJA) mal-wajer BLU tat-tajmer.
  • Vjaġġatur 7: Connect Traveler 7(from the LOAD side) to the RED wire of the timer.

Pass 3: Wiring in-naħa TAGĦBIJA

• a. Vjaġġatur 6: Qabbad il-Vjaġġatur 6 (mill-TIMER) mat-terminal KOMUNI ġeneralment iswed jew ikkulurit tar-ram) tas-swiċċ 3-way fuq in-naħa TAGĦBIJA.
• b. Vjaġġatur 3: Qabbad il-Vjaġġatur 3 (mill-TIMER) għal kwalunkwe terminal (ġeneralment kulur ir-ram) tas-swiċċ bi 3 direzzjonijiet fuq in-naħa TAGĦBIJA.
• c. Vjaġġatur 4: Qabbad il-Vjaġġatur 4 (mill-TIMER) mat-tielet terminal (ġeneralment kulur ir-ram) tas-swiċċ 3-way fuq in-naħa TAGĦBIJA.
• d. Traveler 7: Qabbad Traveler 7 (mill-TIMER) mal-wajer sħun tat-tagħbija.

Nota:

1. To replace an existing switch, please make sure that the neutral wire is available in the wall box. Also, make sure that 5 travelers are available between the wall boxes and mark each wire (such as “HOT WIRE, NEUTRAL WIRE. TRAVELER 1, TRAVELER 2..) for identification first.
2. Qabel il-wiring, jekk jogħġbok aqta 'l-enerġija fil-breaker u aqleb it-tajmer għal MANUAL OFF. (Jekk jogħġbok irreferi għall-kapitolu TIBDIL BEJN ŻEWĠ MODI TA' OPERAZZJONI)
3. Wiring:

Pass 1: Wiring in-naħa tal-LINJA

• a. Use a wire nut to connect together the HOT wire (from breaker), a jumper, and Traveler 5(from the 4-way switch box), then connect the jumper to the COMMON terminal (usually black or copper colored) of the 3-way switch on the LINE side.
• b. Vjaġġatur 1: Qabbad il-Vjaġġatur 1 (mill-kaxxa tal-iswiċċ b'4-Way) għal kwalunkwe terminal (ġeneralment kulur ir-ram) tal-iswiċċ bi 3 direzzjonijiet fuq in-naħa tal-LINJA.
• c. Vjaġġatur 2: Qabbad il-Vjaġġatur 2 (mill-kaxxa tal-iswiċċ 4-Way) mat-tielet terminal (ġeneralment kulur ir-ram) tas-swiċċ bi 3 direzzjonijiet fuq in-naħa tal-LINJA.

Pass 2: Wring l-iswiċċ 4-Way

• a. Vjaġġatur 1: Qabbad il-Vjaġġatur 1 (min-naħa tal-LINJA) ma' kwalunkwe terminal tas-swiċċ b'4 direzzjonijiet.
• b. Vjaġġatur 2: Qabbad il-Vjaġġatur 2 (min-naħa tal-LINJA) mat-terminal (fl-istess tarf tal-Vjaġġatur 1) tas-swiċċ b'4 direzzjonijiet.
• c. Vjaġġatur 4: Qabbad il-Vjaġġatur 4 (min-naħa TAGĦBIJA) mat-tielet terminal (f'tarf ieħor) tas-swiċċ b'4 direzzjonijiet.
• d. Vjaġġatur 5: Qabbad il-Vjaġġatur 5 (min-naħa tal-LINJA) mal-Vjaġġatur 3 (min-naħa tat-TAGĦBIJA).

Pass 3: Wring in-naħa TAGĦBIJA/TIMER

• a. Wajer ta 'l-art: Qabbad il-wajer ta' l-art fil-kaxxa tal-ħajt (jew il-kamin ta 'l-ert) mal-wajer AĦDAR tat-tajmer.
• b. Wajer newtrali: Qabbad il-wajer newtrali fil-kaxxa tal-ħajt (mill-breaker) mal-wajer ABJAD tat-tajmer. (Il-wajer newtrali mill-breaker għandu wkoll ikun imqabbad mal-wajer newtrali tat-tagħbija)
• c. Load Hotwire: Connect the Load’s Hotwire in the wall box (from Load such as Light) to the RED wire of the timer.
• d. Vjaġġaturi:
  • Vjaġġatur 3: Qabbad il-Vjaġġatur 3 (mill-iswiċċ 4-way) mal-wajer ISWED tat-tajmer.
  • Vjaġġatur 4: Qabbad il-Vjaġġatur 4 (mill-iswiċċ 4-way) mal-wajer BLUE tat-tajmer.

PASS 4: WISSI L-TIMER MAL-KAXXA TAL-WIRING U IMBAGĦAD IMMONTA L-FAĊĊA.

PASS 5: APPLIKA TRAB GĦALL-KAXXA TAL-WIRING.

DISPLAY TAL-BUTTONI U DISPLAY SCREEN

NEĦĦI L-ISTIKER
Sib it-tab fin-naħa ta' fuq tal-lemin tal-istiker u iġbed biex tneħħi l-istiker mill-wiċċ tal-iskrin.

JISTRIEĦ IL-TIMER
Jekk il-wiri tal-iskrin huwa vojt jew faded, tista 'tiċċarġja l-batterija għal 10 minuti u mbagħad agħfas il-buttuna "RESET" biex tirrisettja s-sistema. Meta s-sistema tkun inizjalizzata, il-wiri tal-iskrin se jkun qed iteptep. Il-wiri LCD se jidher bħal din l-ikona. Agħfas kwalunkwe buttuna f'dan il-ħin jew stenna '2 minuti mingħajr ebda operazzjoni, l-arloġġ se juri.

Nota: Il-ħin tas-sistema u s-settings kollha se jitħassru wara r-reset tas-sistema.

L-issettjar tal-ħin tas-sistema

Example: if it is 12:08 am Monday. please follow the below steps to set the current day and time.

1. Agħfas il-buttuna "PROG", imbagħad agħfas il-buttuna "JUM" sakemm jidher "MO" fuq l-iskrin. (Fig 01)
2. Then press the “HOUR” button until 12:00 am displays on the screen. (Fig 02)
   Nota: jekk jogħġbok oqgħod attent għal AM/PM.
3. Then press the “MIN” button until 12:08 am displays on the screen. (Fig 03)
   Nota: When the current time is correctly set, press the “MANUAL” button to save and quit the clock display screen; or press “PROG” to start setting the programs.
   Jekk l-ebda buttuna ma tkun ippressata fi żmien 6 sekondi, it-tajmer awtomatikament jiffranka l-ħin attwali u jerġa 'lura għall-iskrin tal-wiri tal-arloġġ.

L-issettjar tal-programm

1. Biex tibda tipprogramma avvenimenti ON/OFF, agħfas “PROG” darba waqt l-issettjar tal-arloġġ tas-sistema stage or press PROG twice on the clock display screen. The screen will display “1 ON” and “PROG. (Fig 04)Per example: if you want to turn on a device every day at 8:05 am and turn it off at 9:00 pm, please follow the below steps.
2. Agħfas il-buttuna "JUM" biex tidħol fl-issettjar tal-programm, se tara l-ġranet kollha tal-ġimgħa fuq in-naħa ta 'fuq u "1 ON" fuq ix-xellug tal-wiri. (Fig 05)
   Nota Agħfas "JUM" bosta drabi sakemm ikollok il-kombinazzjoni ta 'ġranet li trid.
   
   Day combination options: MO to SU. Individual day: MO,TU,WE,TH,FR,SA, SU. MO to FR SA, SU
3. Agħfas il-buttuna "SIEGNA" sakemm jintwerew it-8:00 am fuq l-iskrin. (Fig 06)
   Nota: Jekk jogħġbok oqgħod attent għal AM/PM.
4. Agħfas il-buttuna "MIN" sakemm jintwerew it-8:05 am fuq l-iskrin. (Fig 07)
5. Agħfas il-buttuna "PROG" darba biex issettja l-programm "1 OFF". L-iskrin se juri “1 OFF” u “PROG. (Fig 08)
6. Irrepeti l-passi 2 sa 4 biex issettja l-programm “1 OFF. (Fig 09)
7. Jekk trid issettja t-tieni programm ON/OFF, agħfas il-buttuna "PROG" għal darb'oħra, tista 'tirrepeti l-passi 2 sa 6 biex tissettja l-programm, jew agħfas il-"MANWAL" biex tirritorna l-ħin kurrenti. Tista' twaqqaf sa 18-il programm differenti ON u OFF għat-tajmer tiegħek. Biex tagħmel dan, irrepeti biss il-passi 1 sa 6 għall-programm "2 ON" "2 OFF" "3 ON" eċċ...
8. Matul il-proċess ta 'programmazzjoni, tista' tneħħi s-settings preċedenti billi tagħfas il-buttuna "CLR". Meta tagħfas il-“CLR” għat-tieni darba terġa’ tibda s-settings preċedenti.
9. When all ON/OFF events are programmed, press the “MANUAL” button to return to the clock display screen. If no button is pressed within 6 seconds, the timer will automatically save the settings and return to the clock display screen. You can review, ibdel jew ħassar kwalunkwe avveniment bl-istess mod li tipprogramma avveniment.
10. Agħfas u żomm il-buttuna "MANWAL" sakemm tintwera l-ikona AUTO sabiex it-tajmer iħaddem il-programmi.

TAQBLU BEJN ŻEWĠ MODI TA' OPERAZZJONI

It-tajmer jista 'jaħdem f'żewġ modi ta' tħaddim differenti: AUTO u MANUAL. Huma rappreżentati minn ikoni AUTO u MAN fuq l-iskrin. Agħfas u żomm il-buttuna "MANWAL" għal 4 sekondi jew aktar biex taqleb bejn dawn iż-żewġ modi operattivi. Fi kwalunkwe mod ta 'tħaddim, tista' tagħfas il-buttuna "MANWAL" biex tbiddel l-istatus tal-output tat-tajmer.

XEWGĦU/TAT-DST

DST huwa attiv meta l-ikona DST tidher fuq l-iskrin.

SIGURTÀ KAŻ
To activate or deactivate the random security feature, press and hold the “Min” button for 4 seconds or more. The “RND” icon on the screen indicates that the random function is active. In this case, the timer will respectively postpone the ON and OFF events by 0-30 minutes. Please note that at least one ON/OFF program shall be set to activate this feature.

DAWL TA’ L-ISKRIEN
Press any button to turn on the backlight. On the clock display screen, the backlight will go out after 5 seconds without any button operation. When you are setting the system time or programs, the backlight will go out after 90 seconds without any button operation.

SOLUZZJONI TA’ PROBLEMI

PROBLEMA
It-tajmer ma jixgħelx jew jitfi kif ipprogrammat.

KAWŻA POSSIBBLI
Programs were not correctly set. DST or random function is active. The timer is working in manual mode. Programs overlap.

AZZJONI KORETTIVA
Re-program the timer following the operating instructions. Deactivate DST or the random function. Switch the operation mode to AUTO. Review and correct the programs or reprogram the timer.

PROBLEMA
L-ebda wiri tal-iskrin jew wiri faded.

• KAWŻA POSSIBBLI:
  Batterija baxxa.
• AZZJONI KORRETTIVA:
  Enerġizza t-tajmer biex iċċarġja l-batterija interna għal 10 minuti u mbagħad agħfas il-buttuna RESET biex tirrisettja t-tajmer.

Jekk jogħġbok żomm dan il-manwal

• BN-LINK INC.
• 12991 Leffingwell Avenue, Santa Fe Springs
• Assistenza għas-Servizz tal-Klijent: 1.909.592.1881
• E-mail: support@bn-link.com
• http://www.bn-link.com
• Hours: 9 AM – 5 PM PST, Mon – Fri Designed in California and Made in China

Dokumenti / Riżorsi
SU101d 7 Days In Wall Digital Timer Switch Instruction Manual · SU101d, 7 Days In Wall Digital Timer Switch, SU101d 7 Days In Wall Digital Timer Switch

Issolvi l-problemi
This section is intentionally left blank as no troubleshooting information was provided in the input text. However, common issues and solutions for timer switches often include:

• Timer not turning on/off: Check power supply, wiring connections, and programming settings.
• Dwal li jteptep: Ensure proper load compatibility and secure wiring.
• Timer not holding settings: May indicate a power interruption or a need for battery replacement (if applicable).
• No power to the switch: Verify the circuit breaker is on, and the live wire is correctly connected.

Prekawzjonijiet tas-Sigurtà

TWISSIJA: Riskju ta' Xokk Elettriku. Improper installation or use of this timer switch can result in serious injury or death. Always follow these safety precautions:

• Itfi l-Enerġija: ALWAYS turn off the power at the circuit breaker or fuse box before installing, servicing, or removing the timer switch. Verify power is off with a voltagtester.
• Electrician kwalifikat: Jekk m'intix ċert dwar xi parti tal-proċess tal-installazzjoni, ikkonsulta elettriċista kwalifikat.
• Kodiċijiet Lokali: Installa skond il-kodiċi elettriċi nazzjonali u lokali kollha.
• Użu fuq ġewwa biss: This timer switch is designed for indoor use only unless otherwise specified. Do not expose to rain or moisture.
• Wiring kif suppost: Ensure all wire connections are secure and properly insulated. Loose connections can cause overheating and fire.
• Limiti tat-Tagħbija: Do not exceed the maximum electrical ratings of the timer switch (voltage, amperage, u wattage). Overloading can cause damage to the switch and create a fire hazard.
• L-ertjar: Ensure the timer switch is properly grounded to prevent electrical shock.
• Żomm 'il bogħod mit-Tfal: Keep the timer switch and its components out of reach of children.
• Spezzjona għal Ħsara: Do not install or use if the timer switch or its wiring appears damaged.

Mistoqsijiet Frekwenti

This section is intentionally left blank as no FAQ information was provided in the input text. Common questions about timer switches often include:

• Q: Do I need a neutral wire for this timer switch?
  A: Most modern digital timer switches require a neutral wire for proper operation. Check your specific model’s requirements.
• Q: Can I use this timer switch with LED lights?
  A: Many timer switches are compatible with LED lights, but it’s important to check the maximum and minimum load ratings to ensure compatibility and prevent flickering.
• Q: How do I reset the timer switch?
  A: Refer to your specific model’s manual for reset instructions, which often involve a small reset button or a combination of button presses.
• Q: What if my timer switch isn’t working after installation?
  A: Double-check all wiring connections, ensure the circuit breaker is on, and review the programming instructions. If issues persist, consult a qualified electrician.