Manwal tal-Istruzzjonijiet tad-Dwal tar-Roti RAVEMEN FR300 u CL01

1. Introduzzjoni

Thank you for choosing the RAVEMEN FR300 and CL01 Bike Lights bundle. This manual provides essential information for the safe and effective use of your new bike lights. Please read it thoroughly before installation and operation, and retain it for future reference.

Kontenut tal-Pakkett:

• 1 x RAVEMEN FR300 Front Bike Light
• 1 x RAVEMEN CL01 Rear Bike Light
• Mounting accessories for CL01 (saddle rail mount, seatpost strap, zip ties)
• Kejbils tal-iċċarġjar tal-USB

Image 1.1: The RAVEMEN FR300 front light (bottom) and CL01 rear light (top) included in the bundle.

2. Setup u Installazzjoni

2.1 CL01 Rear Light Mounting

The CL01 rear light offers two primary mounting options: under the saddle rail or on the seatpost.

Saddle Rail Mount:

1. Ensure your saddle rails have sufficient spacing. Refer to the diagram below for required dimensions (approximately 42.3mm to 49.15mm).
2. Attach the saddle rail mount to the underside of your saddle rails using the provided zip ties.
3. Slide the CL01 light onto the mount until it clicks securely into place.

Seatpost Mount:

1. Secure the seatpost strap to the back of the CL01 light.
2. Wrap the strap around your bicycle's seatpost and fasten it securely.
3. Adjust the angle of the light for optimal visibility.

Image 2.1: Illustration of the two mounting methods for the CL01 rear light: saddle rail mount (left) and seatpost mount (right).

Image 2.2: Diagram showing the required saddle rail spacing (42.3mm to 49.15mm) for the CL01 saddle rail mount. Please confirm your saddle rail spacing before purchase.

2.2 FR300 Front Light Mounting

The FR300 front light typically mounts to your bicycle's handlebars. Specific mounting instructions will depend on the included bracket type. Generally, secure the bracket to your handlebars and then slide the FR300 light onto the bracket until it locks into place. Ensure the light is firmly attached and pointed forward, slightly angled downwards to illuminate the road without blinding oncoming traffic.

3. Operazzjoni

3.1 Power On/Off

To power on or off either the FR300 or CL01 light, press and hold the power button for approximately 1-2 seconds. A short press typically cycles through light modes.

3.2 CL01 Rear Light Modes

The CL01 rear light features multiple modes to suit various riding conditions and optimize battery life. Short press the power button to cycle through the modes:

• Għoli: 5 Lumens, approximately 5 hours runtime
• Baxx: 2 Lumens, approximately 10 hours runtime
• Warning Flashing: 30 Lumens, approximately 9.5 hours runtime
• Teptip Rapidu: 5 Lumens, approximately 11 hours runtime
• Teptip Bil-mod: 0.5 Lumens, approximately 45 hours runtime

Image 3.1: Visual representation of the CL01 rear light's five modes and their approximate runtimes.

3.3 Smart Auto On/Off Feature (CL01)

The CL01 rear light includes an intelligent auto on/off mode to conserve battery. When activated, the light will automatically turn off after two minutes of stillness. It will then automatically power back on when it detects vibration, indicating you have resumed your ride. This feature is particularly useful for urban cycling with frequent stops.

Image 3.2: Illustration of the CL01's auto on/off functionality, showing it powers off after 2 minutes of idle time and powers on with vibration.

3.4 Brake Detection Feature (CL01)

For enhanced safety, the CL01 features a brake detection system. When the light senses a reduction in speed (braking), it automatically increases its brightness for 2 seconds. This alerts following vehicles or cyclists to your deceleration, reducing the risk of rear-end collisions. Note: This braking mode does not function when the light is set to 'Slow Flashing' mode.

Image 3.3: Depiction of the CL01's brake detection feature, showing the light automatically boosting brightness for 2 seconds upon sensing braking.

3.5 Battery Level Indicator (CL01)

To check the battery level of the CL01, single-click the power button when the light is off. The indicator light will show the current battery status:

• Aħdar: Livell tal-batterija 'l fuq minn 40%
• Aħmar: Battery level between 5% and 40% (charge soon)
• Aħmar li jteptep: Battery level below 5% (charge immediately)

Image 3.4: The CL01 light in hand, illustrating how to check the power level with a single click when off, and the corresponding indicator colors.

3.6 FR300 Front Light Operation

The FR300 front light operates similarly to the CL01. Press and hold the power button to turn it on or off. Short press the power button to cycle through its various light modes (e.g., High, Medium, Low, Flashing). Refer to the specific instructions provided with the FR300 for detailed mode specifications and runtimes.

4. Manutenzjoni

4.1 Iċċarġjar

Both the FR300 and CL01 lights are rechargeable via USB. Use the provided USB cables to connect the lights to a standard USB power source (e.g., computer, wall adapter). The indicator light will typically show red during charging and turn green when fully charged. Avoid overcharging by disconnecting once fully charged.

4.2 Tindif

Clean the light bodies and lenses with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the plastic components or lens coating. Ensure the charging port cover is securely closed to prevent water ingress.

4.3 Ħażna

When storing the lights for extended periods, ensure they are fully charged. Recharge them every 3-6 months to maintain battery health. Store in a cool, dry place away from direct sunlight.

5 Issolvi l-problemi

• Id-dawl ma jixgħelx: Ensure the battery is charged. Press and hold the power button for 1-2 seconds to power on.
• Id-dawl ma jiċċarġjax: Iċċekkja l-kejbil tal-USB u s-sors tal-enerġija. Kun żgur li l-port tal-iċċarġjar huwa nadif u ħieles minn debris.
• CL01 Auto On/Off not working: Ensure the light is in a mode that supports auto on/off. The feature relies on vibration detection; ensure the light is securely mounted.
• CL01 Brake Detection not working: This feature is not active in 'Slow Flashing' mode. Ensure the light is in a compatible mode and securely mounted to detect deceleration accurately.
• Id-dawl jitteptep jew jintefa bla mistenni: This may indicate a low battery. Recharge the light. If the issue persists, contact customer support.

6. Speċifikazzjonijiet

6.1 CL01 Rear Light

Image 6.1: The CL01 rear light mounted on a bicycle, highlighting its 300-degree wide-angle visibility for safety.

6.2 FR300 Front Light

7. Informazzjoni dwar Garanzija

RAVEMEN products are covered by a limited warranty against manufacturing defects. The warranty period typically begins from the date of purchase. Please retain your proof of purchase for warranty claims. For detailed warranty terms and conditions, please refer to the official RAVEMEN websit jew ikkuntattja l-appoġġ tal-klijent.

8. Appoġġ għall-Klijent

If you encounter any issues or have questions regarding your RAVEMEN FR300 and CL01 bike lights that are not covered in this manual, please contact RAVEMEN customer support. You can typically find contact information on the official RAVEMEN websit jew permezz tal-bejjiegħ bl-imnut tiegħek.

Websit: www.ravemen.com (Eżampil-link, jekk jogħġbok ivverifika l-uffiċjal websit)

Email: support@ravemen.com (Example email, please verify official support email)