1. Introduzzjoni
The FLSUN S1 Pro is an advanced FDM Delta 3D printer designed for high-speed and high-precision additive manufacturing. It features an ultra-fast printing speed of up to 1200mm/s and an acceleration of 40,000mm/s², significantly reducing print times. Equipped with Klipper firmware, a 7-inch smart touch screen, and a 350℃ all-metal hotend, the S1 Pro supports a wide range of filaments, including high-performance engineering materials. Its large build volume of Φ320*320*430 mm³ accommodates substantial projects. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your FLSUN S1 Pro 3D Printer.
Stampa 1.1: Quddiem view of the FLSUN S1 Pro 3D Printer, showcasing its sleek design and enclosed build chamber.
2. X'hemm fil-Kaxxa
Meta tiftaħ il-pakkett, jekk jogħġbok ivverifika li l-komponenti kollha huma preżenti:
- FLSUN S1 Pro 3D Printer (main unit)
- Filament Dryer Kaxxa
- Kejbil tal-Enerġija
- Cable USB
- Kit tal-Għodda (diversi spaners, tornavit, eċċ.)
- Sample Filament
- Manwal għall-Utent (dan id-dokument)
- Gwida Quick Start
Image 2.1: The FLSUN S1 Pro 3D Printer and its included accessories, demonstrating its 95% pre-assembled state.
3. Istruzzjonijiet ta' Setup
The FLSUN S1 Pro is designed for quick setup, being 95% pre-assembled. The initial setup typically takes less than 10 minutes.
- Spakkjar: Oħroġ il-printer u l-aċċessorji kollha mill-imballaġġ bir-reqqa.
- Pjazzament: Poġġi l-istampatur fuq wiċċ stabbli u livellat f'żona ventilata sew.
- Assemblea: Install the door and glass panels as per the instructions in the detailed Manwal tal-Installazzjoni (PDF).
- Konnessjoni tal-Enerġija: Qabbad il-kejbil tal-enerġija mal-istampatur u ma' sokit tal-enerġija adattat.
- Qawwa Inizjali Mixgħula: Turn on the printer using the main power switch. The device will perform self-checks to ensure stability.
- Invellar awtomatiku: The printer features automatic leveling. Follow the on-screen prompts on the 7-inch touch screen to initiate and complete the leveling process. This ensures optimal print bed calibration.
- Tagħbija tal-filament: Load your desired filament into the filament dryer box and then guide it into the extruder as instructed on the display.
- Konnessjoni tan-Netwerk: Connect the printer to your local Wi-Fi network via the touch screen interface for remote monitoring and control.
Għal struzzjonijiet viżwali dettaljati, jekk jogħġbok irreferi għall-uffiċjal Manwal tal-Installazzjoni (PDF).
4. Istruzzjonijiet Operattivi
4.1 User Interface and Control
The FLSUN S1 Pro utilizes a 7-inch Klipper firmware smart touch screen for intuitive control. The visual operation interface allows for smart adjustment and monitoring directly from the printer. Additionally, with advanced Microtac radar control and Wi-Fi connectivity, you can monitor and control your printer in real-time from mobile phones and PCs.
Image 4.1: Remote control and monitoring capabilities via the FLSUN World app on a mobile device.
- Kontroll mill-bogħod: Manage your printers remotely from anywhere.
- Tap it, Print it, Like it: Start printing tasks with a quick tap on the FLSUN World app, utilizing cloud storage for G-code files.
- Monitor in Pocket: Real-time checking of your printing progress.
- Smart Reminder: Receive notifications when print errors occur.
4.2 Proċess tal-Istampar
- Ipprepara l-Mudell: Use compatible slicing software (FLSUN Slicer V2.0 or other slicers like PrusaSlicer, Cura) to prepare your 3D model. Ensure settings are optimized for the S1 Pro's capabilities, including its high speed and acceleration.
- Trasferiment File: Ittrasferixxi l-kodiċi G imqatta' file to the printer via USB or Wi-Fi (FLSUN World app).
- Ibda Stampa: Agħżel il- file on the touch screen or through the app and initiate the print.
- Monitoraġġ: Utilize the built-in camera for real-time monitoring and time-lapse recording. The printer's low noise level (55dB) ensures a quiet operating environment.
- Power-Off Resume: In case of power interruption, the printer supports power-off continuous printing, resuming from where it left off. Vibration compensation further ensures print quality.
Image 4.2: Illustration of the FLSUN S1 Pro's epic speed capabilities: 1200mm/s max printing speed, 40000mm/s² max acceleration, and 110mm³/s peak flow rate.
Image 4.3: Key features for smooth and consistent printing, including AI-powered functions, auto-leveling, spaghetti detection, and perfect first layer adhesion.
Image 4.4: Advanced features like the Air Filter, Filament Dryer, Built-in camera, Intelligent Zoned Heating, and 16GB EMMC storage.
5. Manutenzjoni
Regular maintenance ensures the longevity and optimal performance of your FLSUN S1 Pro 3D Printer.
- Tindif: Regularly clean the print bed, nozzle, and internal components to prevent debris buildup. Use a soft cloth and appropriate cleaning solutions.
- Filtru tal-Arja: The printer is equipped with a combined HEPA + activated carbon air filter. Check and replace the filter periodically as needed to maintain air quality and prevent odors.
- Filament Dryer Box: Ensure the filament dryer box is functioning correctly to keep your filament dry, which is crucial for print quality.
- Spezzjoni taż-żennuna: Periodically inspect the 0.4mm hardened steel nozzle for wear or clogs. Replace if necessary. The all-metal hot end can reach up to 350°C, supporting various high-temperature filaments.
- Lubrikazzjoni: Refer to the detailed manual for any lubrication requirements for moving parts.
Image 5.1: Diagram illustrating the 350°C hotend, 50°C chamber, and 120°C hot bed for optimal material handling.
6 Issolvi l-problemi
Din it-taqsima tindirizza kwistjonijiet komuni li tista' tiltaqa' magħhom waqt l-operazzjoni.
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| Print Not Sticking to Bed | Improper bed leveling, dirty print surface, incorrect bed temperature. | Re-run auto-leveling. Clean the print surface with isopropyl alcohol. Adjust hot bed temperature according to filament type (Max 120°C). |
| Filament Clogging | Dust in filament, incorrect hotend temperature, worn nozzle, heat creep. | Ensure filament is dry (use filament dryer). Verify hotend temperature (Max 350°C). Clean or replace nozzle. Check cooling fan operation. |
| "Spaghetti" Prints | Poor bed adhesion, model detaching, extrusion issues. | The S1 Pro features Sejbien tal-ispagetti. Ensure proper bed adhesion. Monitor print progress via the built-in camera. |
| Il-Printer Mhux Jirrispondi | Software glitch, loose connection, power issue. | Restart the printer. Check all cable connections. Ensure stable power supply. |
| Kwalità Fqira tal-Istampar | Incorrect slicing settings, worn nozzle, vibration, wet filament. | Optimize slicing parameters. Replace nozzle if worn. The printer has Kumpens tal-Vibrazzjoni; ensure it's active. Use filament dryer. |
Image 6.1: Features like the 55dB quiet fan and Power Off Resume Print (UPS) contribute to a reliable printing experience.
7. Speċifikazzjonijiet Tekniċi
| Kategorija | Speċifikazzjoni | Dettalji |
|---|---|---|
| Ġenerali | Veloċità massima tal-istampar | 1200mm/s |
| Aċċelerazzjoni massima | 40000mm/s² | |
| Rata tal-Fluss tal-Ogħla | 110mm³/s | |
| Ibni Volum | Φ320*320*430 mm³ (Maximum height of the cylinder: 383mm) | |
| Awla | Magħluq | |
| Livell ta' Storbju | 55dB | |
| Kap tal-Għodda | Żennuna | 0.4mm Hardened Steel Nozzle (supports various nozzle sizes) |
| Max Hot End Temp | 350℃ | |
| Dijametru tal-filament | 1.75mm | |
| Filament | Filament Sostnut | Ideal: PLA, PETG, TPU. Satisfactory: ABS, ASA, PA, PC, PET. Capable: Carbon/Glass Fiber Reinforced PLA, PPS-CF, PPA-CF/GF. |
| Active Heating Dry Box | Iva | |
| Sejbien tal-Imblukkar tal-filament | Iva | |
| Heatbed | Ibni Pjanċa | Pjanċa PEI bit-Tessut |
| Max Build Plate Temp | 120℃ | |
| Tisħin Żona Intelliġenti | Inner Circle Ø220mm, Outer Ring 220-320mm | |
| Elettronika | Wiri | 7" Color Touch Screen |
| Ħażna | 16GB EMMC, 32GB USB Flash | |
| Provvista tal-Enerġija | 110-240V, 50/60Hz | |
| Konsum tal-Enerġija bil-modalità Mixgħul | 400 watt | |
| Software | Firmware Upgrade | OTA (Over-The-Air) |
| Softwer għat-tqattigħ | FLSUN Slicer V2.0, Other Slicers | |
| OS appoġġjat | MacOS, Windows | |
| Karatteristiċi | Monitoraġġ Kamera | Realtime, Timelapse |
| Sejbien tal-filament | Iva | |
| Kumpens tal-Vibrazzjoni | Iva | |
| Sejbien tal-fdalijiet | Iva | |
| Sejbien tal-ispagetti | Iva | |
| Screen Auto Sleep | Iva | |
| Printer Auto Power Off | Iva | |
| Auto-Leveling | Iva | |
| Jirkupraw Telf ta 'Qawwa | Yes (Z lift, Backup Battery) | |
| Filtru tal-Ajru | HEPA + Activated Carbon | |
| Dimensjonijiet Fiżiċi | Dimensjonijiet tal-Prodott (P x W x H) | 23.62"D x 34.25"W x 9.45"H (600mm x 870mm x 240mm approx.) |
| Physical Dimension (Printer) | 550 * 596 * 1030mm | |
| Piż tal-oġġett | 113 liri (madwar 51.2 kg) | |
| Kulur | Iswed |
Image 7.1: Comprehensive technical specifications for the FLSUN S1 Pro 3D Printer.
8. Garanzija u Appoġġ
FLSUN is committed to providing reliable products and excellent customer service.
- Ritorni: The product is eligible for 30-day easy returns. Please refer to the retailer's return policy for specific details.
- Appoġġ għall-Klijent: For technical assistance, troubleshooting, or warranty inquiries, please contact FLSUN Customer Support. You can often find support resources and contact information on the official FLSUN webis-sit jew permezz tal-bejjiegħ bl-imnut minn fejn inxtara l-prodott.
- Pjanijiet ta' Protezzjoni: Extended protection plans, such as a 4-Year Protection Plan, may be available for purchase separately to provide additional coverage beyond the standard warranty.
- Riżorsi onlajn: Żur il- FLSUN Store on Amazon for additional product information, FAQs, and support.
