Manwal tal-Utent tas-Siġġu Ergonomu tal-Uffiċċju ProtoArc EC100

Introduzzjoni

Thank you for choosing the ProtoArc Ergonomic Office Chair EC100. This manual provides detailed instructions for the assembly, operation, maintenance, and troubleshooting of your new office chair. Please read this manual thoroughly before assembly and use to ensure proper function and longevity of the product. Retain this manual for future reference.

Image: The ProtoArc Ergonomic Office Chair EC100, showcasing id-disinn iswed eleganti tiegħu u l-karatteristiċi ergonomiċi.

Informazzjoni dwar is-Sigurtà

Biex tiżgura tħaddim sikur u tevita ħsara, jekk jogħġbok osserva l-linji gwida ta' sigurtà li ġejjin:

• Kapaċità massima tal-piż: Teċċedix il-kapaċità massima tal-piż ta' 260 lbs (118 kg). Overloading the chair can lead to instability and potential injury.
• Assemblaġġ kif suppost: Ensure the chair is properly assembled according to the instructions provided in this manual. Incorrect assembly can compromise the chair's stability and safety.
• Wiċċ Stabbli: Always use the chair on a flat, stable, and level surface to prevent tipping.
• Spezzjoni regolari: Periodically check all bolts, screws, and connections to ensure they are tight. Retighten as necessary.
• Avoid Standing on Chair: Toqgħodx bilwieqfa fuq is-siġġu u lanqas tużah bħala banketta.
• Tfal u Pets: Keep children and pets away from the chair during assembly. Do not allow children to play on or around the chair unsupervised.
• Nimxu s-Siġġu: When moving the chair, lift it rather than dragging it to prevent damage to the base or floor.

Kontenut tal-Pakkett

Before beginning assembly, please verify that all components are present and undamaged. If any parts are missing or damaged, contact customer support immediately.

• Dahar tas-siġġu
• Assemblaġġ tal-kuxxin tas-sedil
• Armrests (2)
• Chair Base (5-star)
• Xandara (5)
• Ċilindru tal-Lift tal-Gass
• Pjanċa tal-Mekkaniżmu
• Serħan tar-ras
• Kit tal-Ħardwer (viti, woxers, Allen wrench)
• Manwal għall-Utent (dan id-dokument)

Istruzzjonijiet ta' Armar

Assembly typically takes approximately 20 minutes. All necessary tools and hardware are included in the package. Follow these steps carefully:

1. Waħħal ir-Roti mal-Bażi: Insert each of the five casters into the holes at the end of each leg of the chair base. Push firmly until they click into place.
   

   Image: The chair's five-star base with casters attached, ready for the gas lift cylinder.

2. Daħħal il-Gass Lift: Place the gas lift cylinder into the center hole of the assembled chair base. Ensure it is seated securely.
3. Waħħal il-Pjanċa tal-Mekkaniżmu mas-Sedil: Allinja l-pjanċa tal-mekkaniżmu mat-toqob imtaqqbin minn qabel fuq in-naħa ta’ taħt tal-kuxxin tas-sedil. Waħħalha billi tuża l-viti u l-wrench Allen provduti. Kun żgur li l-parti ta’ quddiem tal-mekkaniżmu tħares lejn in-naħa ta’ quddiem tas-sedil.
4. Waħħal id-Dirgħajn mas-Sedil: Secure the armrests to the sides of the seat cushion using the designated screws. Ensure they are oriented correctly (left and right).
5. Waħħal id-Dahar tas-Sedil: Connect the backrest to the seat cushion assembly. Secure it with the provided screws.
6. Waħħal ir-Rasrest: Slide the headrest into the top slot of the backrest. It should click into place or be secured with a screw, depending on the design.
7. Qabbad is-Sedil mal-Lift tal-Gass: Carefully place the assembled seat and backrest onto the gas lift cylinder, ensuring the center hole of the mechanism plate aligns with the top of the gas lift. Press down firmly to secure.
   

   Image: An illustration showing the fully assembled ProtoArc EC100 chair, highlighting its overall structure and key components.

Istruzzjonijiet Operattivi

The ProtoArc EC100 chair offers multiple adjustment features to customize your seating experience for optimal comfort and ergonomic support.

1. Aġġustament tal-Għoli tas-Sedil

To adjust the seat height, locate the lever on the right side beneath the seat. Pull the lever upwards while seated to lower the seat, or pull the lever upwards while standing to raise the seat. Release the lever at your desired height. The SGS-certified gas cylinder allows for a 3.9-inch adjustment range, accommodating users from approximately 5.3ft to 6.5ft.

2. Recline Function and Locking

The chair features a two-mode locking tilt mechanism, allowing recline angles from 90 to 130 degrees. To recline, pull the recline lever (typically on the left side) outwards and lean back. To lock the recline position, push the lever inwards at your desired angle. The chair supports two primary locked positions: fully upright (90°) and fully reclined (130°).

3. Headrest aġġustabbli

The headrest can be adjusted both vertically and rotationally to provide optimal neck and head support.

• Aġġustament Vertikali: Gently pull the headrest up or push it down to adjust its height by up to 2.75 inches.
• Rotational Adjustment: Tilt the headrest forward or backward to find the most comfortable angle. It rotates up to 60 degrees.

Immaġni: Close-up view illustrating the 2.7-inch vertical and 60-degree rotational adjustment capabilities of the headrest.

4. Aġġustament tad-Dirgħajn

The 2D armrests can be adjusted vertically by 3.5 inches to suit various working positions and desk heights. To adjust, locate the button or lever on the side of each armrest, press it, and slide the armrest up or down. Release the button/lever to lock it in place.

5. Lumbar Support

The chair features a broad curved lumbar support designed to conform to the natural curve of your spine, promoting healthy posture. This support is integrated into the backrest design.

Image: A visual representation of the broad curved lumbar support, highlighting how it cradles the lower back for ergonomic comfort.

Manutenzjoni

Regular maintenance will help prolong the life and appearance of your ProtoArc EC100 chair.

• Cleaning Mesh and Fabric: For general cleaning, use a soft cloth dampened with mild soap and water. Gently wipe the mesh backrest and fabric seat cushion. Avoid abrasive cleaners or harsh chemicals, as they can damage the material. Allow to air dry completely.
• Cleaning Plastic and Metal Parts: Wipe plastic and metal components with a soft, damp drapp. Nixxef sewwa.
• Manutenzjoni tal-Caster: Periodically check the casters for accumulated hair or debris. Clean them as needed to ensure smooth rolling.
• Iċċekkja tal-Hardware: Every 3-6 months, inspect all screws and bolts to ensure they are tight. Retighten any loose fasteners to maintain stability and safety.
• Evita dawl tax-xemx dirett: Prolonged exposure to direct sunlight can cause fading and degradation of materials. Position the chair away from direct sunlight when possible.

Issolvi l-problemi

If you encounter any issues with your ProtoArc EC100 chair, refer to the following common problems and solutions:

If these solutions do not resolve the issue, please contact ProtoArc customer support for further assistance.

Speċifikazzjonijiet

Image: A diagram illustrating the key dimensions of the ProtoArc EC100 chair, including height, width, and depth.

Image: An infographic detailing the extensive durability tests the ProtoArc EC100 chair has undergone, including tilt, backrest, armrest, caster, gas lift, and seat durability tests.

Garanzija u Appoġġ

ProtoArc stands behind the quality of its products. For specific warranty details, please refer to the warranty card included with your purchase or visit the official ProtoArc websit.

Appoġġ għall-Klijent: If you have any questions, require assistance with assembly, or need to report a missing/damaged part, please contact ProtoArc customer support. Have your model number (EC100) and purchase information ready when contacting support.

Għall-aktar informazzjoni ta' kuntatt aġġornata, jekk jogħġbok żur il- ProtoArc Store on Amazon.