SYNCO XTalk XPro2 2.4GHz Wireless Intercom Headset System

1. Introduzzjoni

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your SYNCO XTalk XPro2 2.4GHz Wireless Intercom Headset System. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.

Figure 1: SYNCO XTalk XPro2 Headset System and Accessories

2. Prodott Aktarview

The SYNCO XTalk XPro2 is a full-duplex wireless intercom headset system designed for professional team communication. Key features include:

• Riċeviment tas-Sinjal Imtejjeb: External antennas provide a reliable 500m (1640ft) connection range.
• Tnaqqis Avvanzat tal-Ħsejjes: Features 2.0 AEC algorithm (150Hz to 7KHz) for clear voice recognition in noisy environments.
• Flexible Team Communication: Supports up to 13-unit connections with group expansion technology.
• Modalità Boost: Enhances signal strength for stable communication through obstacles.
• Modalità Dominanti: One-button remote muting function for the Master headset.
• Ħajja twila tal-batterija: Over 24 hours of use with rechargeable and replaceable batteries.
• Monitoraġġ f'ħin reali: 3.5mm monitoring jack for simultaneous communication and device audio monitoring.

Figure 2: Enhanced Signal Reception

Figure 3: Advanced AEC Noise Reduction

3. Setup

3.1 Tqabbil Manwali

Follow these steps to manually pair your headsets:

1. Ixgħel il-kuffji tal-widna kollha.
2. Set one headset as the Master and the others as Level 1.
3. Within 1 minute, long press all 'A' buttons. Release after the first beep. You will hear "Pairing Succeed".
4. Restart all headsets.

3.2 Using SYNCO EasyGo Software

For quick firmware upgrades, voice pack installations, and headset pairing, use the SYNCO EasyGo software. Refer to the user guide for software download and usage instructions from the SYNCO official site.

Figure 4: SYNCO EasyGo Software Interface

4. Istruzzjonijiet Operattivi

4.1 Issettjar tal-Volum

Short press the volume '+' or '-' buttons on the headset to adjust the listening volume.

4.2 Mute/Unmute Microphone

To mute or unmute the microphone, rotate the boom arm up or down. Rotating it up mutes the microphone, and rotating it down unmutes it.

4.3 Kanċellazzjoni tal-Istorbju

Short press button 'B' to toggle noise cancellation on or off. You will hear a beep to confirm the change.

4.4 Dominant Mode

Press and hold button 'B' to enter Dominant Mode. This mode allows the Master headset to mute all remote headsets instantly. Release the button to exit Dominant Mode.

4.5 Modalità Boost

Long press the volume '-' button to hear a "beep", then release to switch between Mode 1, Mode 2, and Mode 3. Mode 2 is the default. Boost Mode enhances signal strength for stable communication, especially through obstacles.

4.6 Monitoraġġ f'Ħin Reali

Connect the headset to a device (e.g., camera, recorder) via the 3.5mm TRS port for real-time audio monitoring. This port is for monitoring only and does not output audio.

Figure 5: Real-Time Monitoring Setup

5. Indikaturi

The LED indicator on the microphone boom arm provides status information:

• Dawl Aħdar Sod: Tqabbil Suċċess
• Green Light Flashing Slow: Mhux Konnessi
• Green/Yellow Lights Alternating: Kanċellazzjoni tal-Ħoss Mitfi
• Red Light Flashing Slow: Batterija Baxxa
• Dawl aħmar fiss: Iċċarġjar

6. Manutenzjoni

To ensure the longevity and optimal performance of your SYNCO XTalk XPro2 headset system, follow these maintenance guidelines:

• Tindif: Uża drapp artab u niexef biex tnaddaf il-headset. Evita li tuża kimiċi ħarxa jew materjali li joborxu.
• Ħażna: Aħżen il-headset f'post frisk u niexef 'il bogħod mix-xemx diretta u minn temperaturi estremi.
• Kura tal-batterija: The system uses rechargeable and replaceable Lithium-Ion batteries. Ensure batteries are fully charged before extended use and stored properly if not used for long periods.
• Protezzjoni tal-Mikrofonu: Keep the microphone foam cover clean and replace if damaged to maintain audio quality.

Figura 6: Ħajja tal-Batterija ta' 24 Siegħa

7 Issolvi l-problemi

If you encounter issues with your SYNCO XTalk XPro2 system, refer to the following common problems and solutions:

• No Audio/Intermittent Connection:
  • Ensure all headsets are powered on and fully charged.
  • Verify proper pairing between Master and Level 1 headsets (refer to Section 3.1).
  • Check the operating range; move closer to the Master headset.
  • Restart all headsets.
• Kwalità tal-Awdjo Fqira/Storbju Eċċessiv:
  • Ensure Noise Cancellation is activated (refer to Section 4.3).
  • Check microphone position and ensure it is not obstructed.
  • Verify that the microphone boom arm is fully down for unmuted operation.
• Il-Headset Mhux Qed Jiċċarġja:
  • Kun żgur li l-kejbil tal-iċċarġjar huwa konness sew kemm mal-headset kif ukoll mas-sors tal-enerġija.
  • Iċċekkja s-sors tal-enerġija għall-funzjonalità.
  • Verify the charging indicator (Red Light Steady) as per Section 5.

8. Speċifikazzjonijiet

9. Garanzija u Appoġġ

For warranty information, technical support, or service inquiries, please refer to the official SYNCO webis-sit jew ikkuntattja lis-servizz tal-konsumatur tagħhom direttament. Żomm l-irċevuta tax-xiri tiegħek bħala prova tax-xiri għal talbiet ta' garanzija.