PRORUN 25.4cc 17-inch Gas-Powered 2-Cycle Straight Shaft Trimmer User Manual

1. Informazzjoni dwar is-Sigurtà

Always read and understand all safety warnings and instructions before operating this gas-powered trimmer. Failure to follow these instructions may result in serious injury or death.

Twissijiet ta' Sigurtà Ġenerali

• Tagħmir Protettiv Personali (PPE): Always wear eye protection (safety glasses or goggles), hearing protection, heavy-duty long pants, long sleeves, gloves, and sturdy footwear when operating the trimmer.
• Immaniġġjar tal-Fjuwil: Handle gasoline with extreme care. It is highly flammable. Store fuel in an approved container in a well-ventilated area, away from sparks, open flames, or other ignition sources. Never refuel a hot engine.
• Żona tax-Xogħol: Keep children, bystanders, and pets at least 50 feet (15 meters) away from the work area. Clear the work area of debris, rocks, and other objects that could be thrown by the cutting line.
• Operazzjoni: Operate the trimmer only in well-ventilated outdoor areas. Do not operate in wet conditions. Maintain a firm grip on the trimmer with both hands. Avoid contact with the rotating cutting line.
• Manutenzjoni: Disconnect the spark plug wire before performing any maintenance or repairs to prevent accidental starting.

2. Kontenut tal-Pakkett

Verify that all items are present in the package before assembly.

• PRORUN 25.4cc 17-inch Gas-Powered 2-Cycle Straight Shaft Trimmer (Powerhead and Shaft Assembly)
• Trimmer Head with .095 line
• Deflector Shield
• Adjustable Loop Handle
• Xedd
• Maintenance Tools (Wrench, Screwdriver)
• Manwal tas-Sid

Figure 2.1: PRORUN PSST217 Trimmer and included accessories, including maintenance tools and a shoulder harness.

3. Istruzzjonijiet tal-Assemblea

Follow these steps to assemble your PRORUN Straight Shaft Trimmer.

3.1 Attaching the Deflector Shield

1. Align the deflector shield with the mounting holes on the trimmer shaft.
2. Secure the shield using the provided screws and tighten them firmly with a screwdriver. Ensure the shield is stable and does not wobble.

3.2 Installing the Loop Handle

1. Slide the adjustable loop handle onto the trimmer shaft.
2. Position the handle for comfortable operation, typically around the middle of the shaft.
3. Issikka l-manku clamp securely to prevent rotation during use.

Figure 3.1: Key components of the PRORUN trimmer, including the engine, adjustable loop handle, durable cast aluminum shaft, and 17-inch bump-feed cutting head.

4. Twaqqif u Riforniment tal-Fjuwil

Proper fuel mixture and starting procedures are crucial for optimal performance and longevity.

4.1 Taħlit tal-Fjuwil

This trimmer uses a 2-cycle engine and requires a mixture of gasoline and 2-cycle engine oil. Refer to the engine oil manufacturer's instructions for the correct mixing ratio, typically 50:1 (2.6 oz of oil per gallon of gasoline) or 40:1 (3.2 oz of oil per gallon of gasoline).

• Uża gażolina friska, bla ċomb b'klassifikazzjoni tal-ottan ta' 89 jew ogħla.
• Uża żejt tal-magna b'2 ċikli ta' kwalità għolja ddisinjat speċifikament għal magni mkessħin bl-arja.
• Mix fuel in an approved fuel container. Shake the container thoroughly before fueling the trimmer.

4.2 Fueling the Trimmer

1. Ensure the engine is cool and turned off.
2. Poġġi t-trimmer fuq wiċċ ċatt u stabbli.
3. Iftaħ l-għatu tal-fjuwil bir-reqqa.
4. Pour the mixed fuel into the fuel tank, avoiding overfilling.
5. Erġa’ poġġi l-għatu tal-fjuwil sew. Imsaħ kwalunkwe fjuwil imxerred immedjatament.

Figure 4.1: The engine and large, easy-fill fuel tank of the PRORUN trimmer.

5. Istruzzjonijiet Operattivi

Learn how to start, operate, and stop your PRORUN trimmer safely and effectively.

5.1 Starting the Engine (Spring-Assist Starting)

1. Place the trimmer on a flat, clear surface.
2. Set the ON/OFF switch to the 'ON' position.
3. Press the primer bulb 7-10 times until fuel is visible in the return line.
4. Move the choke lever to the 'FULL CHOKE' position.
5. Pull the starter rope slowly until resistance is felt, then pull quickly and firmly 1-3 times until the engine 'pops' or attempts to start.
6. Move the choke lever to the 'HALF CHOKE' position.
7. Pull the starter rope quickly and firmly 1-3 times until the engine starts.
8. Once the engine runs, move the choke lever to the 'RUN' position. Allow the engine to warm up for 30-60 seconds before operating at full throttle.

Figure 5.1: Location of the primer bulb for engine starting.

5.2 It-tħaddim tat-Trimmer

• Żomm it-trimmer sew b'żewġ idejn, u żgura li żżomm qagħda bbilanċjata.
• Use the shoulder harness for added comfort and control, especially during extended use.
• Żomm distanza sigura minn oġġetti u persuni fil-qrib.
• Cut grass by swinging the trimmer from side to side, using the tip of the cutting line.
• For edging, tilt the trimmer head to a vertical position and carefully guide it along the edge.

Figure 5.2: The 17-inch cutting swath with .095 line and bump feed head effectively trimming grass.

5.3 Waqfien tal-Magna

To stop the engine, simply move the ON/OFF switch to the 'OFF' position.

6. Manutenzjoni

Manutenzjoni regolari tiżgura l-lonġevità u l-prestazzjoni ottimali tat-trimmer tiegħek.

6.1 Tindif tal-Filtru tal-Arja

The air filter should be checked and cleaned regularly, especially in dusty conditions.

1. Kun żgur li l-magna tkun mitfija u berredha.
2. Locate the tool-less air filter cover.
3. Remove the cover and carefully take out the air filter.
4. Clean the filter by tapping it gently or washing it with warm, soapy water. Allow it to dry completely before reinstallation. Replace if heavily soiled or damaged.

6.2 Spezzjoni ta 'Spark Plug

Spezzjona l-plagg tal-ispark perjodikament għal xedd jew akkumulazzjoni ta' karbonju.

1. Skonnettja l-wajer tal-ispark plug.
2. Use the provided spark plug wrench to remove the spark plug.
3. Clean any carbon deposits with a wire brush. Check the electrode gap and adjust if necessary (refer to specifications for correct gap). Replace if worn or damaged.

6.3 Trimmer Line Replacement

The trimmer head uses .095-inch diameter line. Replace the line when it becomes too short or worn.

1. Ensure the engine is off and the spark plug wire is disconnected.
2. Locate the bump feed head. Depending on the head design, you may need to press tabs or unscrew a cap to access the spool.
3. Remove any remaining old line.
4. Cut a new length of .095-inch trimmer line (typically 15-20 feet).
5. Follow the arrows on the trimmer head to correctly wind the new line onto the spool. Leave a few inches of line protruding from the eyelets.
6. Reassemble the trimmer head.

Figure 6.1: The bump feed trimmer head, showing the cutting line exit points.

7 Issolvi l-problemi

Din it-taqsima tindirizza kwistjonijiet komuni li tista’ tiltaqa’ magħhom bit-trimmer tiegħek.

8. Speċifikazzjonijiet

9. Garanzija u Appoġġ

PRORUN offers a limited warranty for this product.

• Użu Residenzjali: Garanzija Limitata ta' 3 Snin
• Użu Kummerċjali: Garanzija Limitata ta' 1 Snin

For warranty claims, technical support, or replacement parts, please contact PRORUN Customer Service.

• Telefon: 1-844-905-0882
• Email: info@proruntech.com

Figure 9.1: PRORUN Limited Warranty details for residential and commercial use.