Manwal ta' Istruzzjoni tal-Apparat tad-Dawl ta' Għargħar Lithonia Lighting OFTH 300PR 120 WH Twin PAR

1. Informazzjoni dwar is-Sigurtà

Please read and understand all instructions before beginning installation. Failure to do so may result in electric shock, fire, or other hazards that could cause injury or property damage.

• TWISSIJA: Risk of fire and electrical shock. This product must be installed by a qualified electrician only.
• Always disconnect power at the fuse or circuit breaker before installing or servicing.
• Kun żgur li l-konnessjonijiet elettriċi kollha jikkonformaw mal-kodiċijiet u l-ordinanzi lokali, kif ukoll mal-Kodiċi Elettriku Nazzjonali (NEC).
• This fixture is rated for wet locations.
• Use only outdoor-rated PAR medium base flood light bulbs up to 150W (not included).

2. Prodott Aktarview

The Lithonia Lighting OFTH Twin PAR Holder is a durable and reliable outdoor lighting solution designed for focused illumination in residential and light commercial areas. It is suitable for driveways, patios, walkways, and other exterior spaces, enhancing both visibility and security.

This fixture features a rugged die-cast aluminum canopy and socket holders, providing resistance against rust and harsh weather conditions. The tool-free adjustable heads allow for precise light direction, offering up/down and side-to-side aiming. It is hardwired and operates with a standard on/off light switch.

Figura 2.1: Aktarview of the OFTH Twin PAR Holder, emphasizing its reliability and ease of use.

Figure 2.2: The fixture features tool-free adjustable heads for directing light precisely.

3. Kontenut tal-Pakkett

Iċċekkja li l-komponenti kollha huma preżenti qabel tibda l-installazzjoni:

• OFTH Twin PAR Holder Fixture (1)
• Pjanċa tal-Immuntar (1)
• Cross Bar (1)
• Gasket (1)
• Wajer Ġewż (3)
• Viti tal-Immuntar (daqsijiet varji)

Figura 3.1: Sploda view of the fixture components for assembly.

4. Istruzzjonijiet ta 'installazzjoni

This fixture is designed for wall or eave mounting only. Ensure power is turned off at the circuit breaker before proceeding.

4.1. Qabel l-Installazzjoni

• Turn off electricity at the fuse or circuit breaker box.
• Iftaħ l-apparat bir-reqqa mill-pakkett u spezzjona għal xi ħsara.

4.2. Immuntar tal-Apparat

1. Install the Cross Bar to the junction box using the two screws provided.
2. Position the Gasket on the back of the Mounting Plate, routing the fixture wires through the center of the Gasket.
3. Align the Nipple with the hole in the center of the Mounting Plate and secure with the Nut.

4.3. Konnessjonijiet tal-Wiring

• To ground the fixture, connect the house supply ground wire and the fixture ground (green & yellow wire) to the Green Ground Screw on the Cross Bar. If house wiring does not include a ground wire, consult your local electrical code for approved grounding methods.
• Use Wirenuts to connect the black fixture wire to the black house power supply wire.
• Use Wirenuts to connect the white fixture wire to the white (neutral) house supply wire.
• For proper connection, place the Wirenut over the wires and twist clockwise until tight.

4.4. Assemblea Finali

1. Secure the Mounting Plate to the Cross Bar using the provided screws.
2. Install two outdoor-rated PAR medium base flood light bulbs (up to 150W each, not included) into the lampdetenturi.
3. Aġġusta l-lampholders to illuminate the desired area. Note: Position lampholders below horizontal to avoid water getting into the lampdetenturi.

4.5. Wara l-Installazzjoni

• Turn on electricity at the fuse or circuit breaker box and verify successful operation of the fixture.

Figura 4.1: Eżample of the flood light fixture installed on a house eave.

Figura 4.2: Eżample of the flood light fixture installed above a garage door.

Figura 4.3: Eżample of the flood light fixture installed on an exterior wall.

5. Istruzzjonijiet Operattivi

The OFTH Twin PAR Holder operates with a standard hardwired on/off light switch. Simply toggle the switch to turn the lights on or off as needed.

• Irjus Aġġustabbli: Il-lampholders can be adjusted up, down, and side-to-side to direct the light to specific areas. Loosen the adjustment screws, position the lampholders, and then tighten the screws to secure them.

6. Manutenzjoni

Regular maintenance ensures optimal performance and longevity of your flood light fixture.

• Tindif: Naddaf l-apparat perjodikament b'ċarruta ratba, damp drapp. Tużax prodotti tat-tindif jew solventi li joborxu, għax dawn jistgħu jagħmlu ħsara lill-finitura.
• Sostituzzjoni tal-bozza: Ensure power is disconnected at the circuit breaker before replacing bulbs. Allow bulbs to cool completely before handling. Unscrew the old bulb and screw in a new outdoor-rated PAR medium base flood light bulb (up to 150W).

7 Issolvi l-problemi

If the fixture does not operate correctly, refer to the following common issues:

• Ebda Qawwa: Check the circuit breaker to ensure power is on. Verify all wire connections are secure.
• Bozza Mhux Dawl: Ensure bulbs are screwed in tightly and are not burnt out. Replace with new bulbs if necessary.
• Operazzjoni intermittenti: Check for loose wiring connections or damaged bulbs.

Jekk il-problemi jippersistu, ikkonsulta elettriċista kwalifikat.

8. Speċifikazzjonijiet

9. Garanzija

This Lithonia Lighting fixture comes with a one-year limited warranty. For specific terms and conditions, please refer to the warranty documentation included with your product or contact customer support.

10. Appoġġ

For technical assistance, replacement parts, or further information, please contact Lithonia Lighting customer support. Contact details can typically be found on the product packaging or the official Lithonia Lighting websit.