WALI Dual Monitor Wall Mount (Model: 012ARM-38)

Introduzzjoni

This manual provides detailed instructions for the safe and proper installation and operation of your WALI Dual Monitor Wall Mount, Model 012ARM-38. Please read all instructions carefully before assembly and use. If you have any questions, please contact WALI customer support.

Informazzjoni Importanti dwar is-Sigurtà

TWISSIJA: Failure to read and follow all instructions can result in personal injury or property damage.

• Do not install into drywall alone. The mount must be secured into a wood stud, concrete wall, or brick wall.
• Ensure the mounting surface can safely support the combined weight of the mount and your monitors.
• Do not exceed the maximum weight capacity of 19.8 lbs (9 kg) per arm.
• This mount is designed for monitors between 17 and 38 inches with VESA mounting patterns of 75x75mm or 100x100mm.
• Use a stud finder to locate wood studs accurately. For concrete or brick walls, use appropriate anchors (not included).
• Always use a level to ensure the mount is installed straight.

Kontenut tal-Pakkett

Ivverifika li l-komponenti kollha huma preżenti u mhux imħassra qabel ma tipproċedi bl-installazzjoni.

• 1 x WALI Dual Monitor Wall Mount (Black)
• Mounting Hardware Kit (screws, washers, spacers, cable clips)
• Manwal għall-Utent

Image: All components of the WALI Dual Monitor Wall Mount, including the main bar, VESA plates, and mounting hardware.

Setup u Installazzjoni

Pass 1: Ipprepara l-Ħajt

1. Use a stud finder to locate a suitable wood stud in your desired mounting location. For concrete or brick walls, ensure you have appropriate masonry anchors and drill bits.
2. Hold the wall plate against the wall at the desired height and use a pencil to mark the drilling locations. Use a level to ensure the plate is perfectly horizontal.
3. Drill pilot holes at the marked locations. The size of the drill bit will depend on your wall type and the screws provided in the hardware kit.
4. Secure the wall plate to the wall using the provided screws. Ensure it is firmly attached.

Image: Visual guide showing suitable wall types for installation: brick wall, wood stud, and concrete wall. A note emphasizes not to mount on drywall alone.

Step 2: Assemble the Monitor Bar

1. Attach the main horizontal bar to the secured wall plate. Use the provided screws and Allen wrench to tighten the connections.
2. Kun żgur li l-konnessjonijiet kollha huma siguri qabel ma tipproċedi.

Pass 3: Waħħal Pjanċi VESA mal-Moniters

1. Carefully place your monitor face down on a soft, clean surface.
2. Align the VESA mounting plate with the mounting holes on the back of your monitor (75x75mm or 100x100mm).
3. Use the appropriate screws and washers from the hardware kit to secure the VESA plate to the monitor. Do not overtighten.

Step 4: Mount Monitors to the Arm

1. With assistance, carefully lift each monitor and slide its VESA plate onto the ends of the horizontal bar.
2. Secure the monitors in place using the provided cap nuts or locking mechanisms.

Image: Two monitors are shown mounted on the wall, illustrating the mount's compatibility with screens up to 38 inches, a weight capacity of 19.8 lbs per arm, and VESA mounting holes of 75x75mm or 100x100mm.

Gwida tal-Vidjow tal-Installazzjoni

Tħaddim u Aġġustament

Monitor Distance Adjustment

The horizontal bar allows for adjustment of the distance between monitors. The maximum distance between the centers of the VESA plates is approximately 37.4 inches, and the minimum is 25.2 inches.

Image: A visual representation of the adjustable distance between two monitors on the mount, highlighting the maximum and minimum possible spans.

Tilt, Swivel, and Rotation

• Mejjel: Adjust the monitor tilt from +45° to -45° to find your optimal viewangolu tal-ing.
• Dawwar: Swivel each monitor +15° to -15° horizontally.
• Rotazzjoni: Rotate the monitors 360° for portrait or landscape orientation.

Image: A monitor is shown tilted and swiveled, demonstrating the adjustable angles for optimal viewkumdità.

Image: A monitor is depicted rotating 360 degrees, showcasing the flexibility to switch between landscape and portrait orientations.

Image: Two monitors are mounted on the wall, one in portrait mode and the other in landscape mode, illustrating the versatile display options.

Ġestjoni tal-Cable

Utilize the provided cable clips to route and organize your monitor cables along the arms for a clean and clutter-free workspace.

Manutenzjoni

• Iċċekkja perjodikament il-viti u l-konnessjonijiet kollha biex tiżgura li jibqgħu ssikkati u siguri.
• Naddaf il-muntatura b'ċarruta ratba, damp drapp. Evita prodotti tat-tindif jew solventi li joborxu.

Issolvi l-problemi

• Monitors are not level: Ensure the wall plate is perfectly level during installation. Fine-tune monitor tilt adjustments if necessary.
• Il-muntatura tħossha instabbli: Recheck all mounting screws and connections. Ensure the mount is securely fastened to a structural element (wood stud, concrete, or brick). Verify that monitor weights do not exceed the maximum capacity.
• Difficulty adjusting monitor position: Check if any adjustment screws are overtightened. Loosen slightly to allow for movement, then re-tighten to hold position.

Speċifikazzjonijiet

Garanzija u Appoġġ għall-Klijent

WALI provides experienced and friendly US-based customer support available to assist 7 days a week. For any questions, concerns, or warranty claims, please contact our support team.

Please refer to the product packaging or WALI's official webis-sit għal dettalji speċifiċi tal-garanzija u informazzjoni ta' kuntatt.