1. Introduzzjoni
This manual provides detailed instructions for the proper use and application of CERAKOTE C-SERIES GLACIER BLACK (C-7600P) air cure ceramic coating. This product is designed to provide a durable, high-performance finish with exceptional chemical resistance and UV stability on various substrates, including metals and polymers.
CERAKOTE C-SERIES coatings are air-cured and ready to spray, requiring no additional catalyst. The Glacier Black (C-7600) variant offers a deep black, sleek satin finish.
2. Informazzjoni dwar is-Sigurtà
WARNING: This product is a chemical coating. Always follow safety precautions.
- Ventilazzjoni: Use in a well-ventilated area or outdoors. Avoid inhaling vapors.
- Tagħmir Protettiv Personali (PPE): Wear appropriate chemical-resistant gloves, eye protection (safety glasses or goggles), and a respirator suitable for organic vapors.
- Kuntatt mal-ġilda: Avoid prolonged or repeated skin contact. Wash thoroughly with soap and water after handling.
- Kuntatt mal-għajnejn: In case of eye contact, flush immediately with plenty of water for at least 15 minutes and seek medical attention.
- Inġestjoni: Tiblax. Jekk jinbela', tinduċix ir-rimettar. Fittex attenzjoni medika immedjata.
- Fjammabilità: Żomm 'il bogħod minn fjammi miftuħa, xrar, u uċuħ sħan.
- Ħażna: Store in a cool, dry place, away from direct sunlight and incompatible materials. Keep container tightly closed when not in use.
3. Prodott Aktarview
The CERAKOTE C-SERIES GLACIER BLACK (C-7600P) is an advanced air-cured ceramic coating formulated for high-temperature applications and environments where extreme durability is required. It provides a deep black, satin finish that maintains its aesthetic and protective qualities under harsh conditions.
Karatteristiċi ewlenin:
- Air-cured, ready-to-spray formula.
- No catalyst required.
- Deep black, sleek satin finish.
- Extremely high chemical resistance.
- UV resistant.
- PFAS free formulation.
Figure 1: CERAKOTE C-7600 Glacier Black 16oz bottle. Note the 'C-Series Coating' and 'Glacier Black' labels, and the 'Important: Solids will settle! Must shake well for proper application' warning.
Figure 2: PFAS Free logo, indicating the product's environmental compliance.
4. Setup and Surface Preparation
Proper surface preparation is critical for optimal adhesion and performance of CERAKOTE coatings. Do not skip or rush these steps.
4.1. Required Equipment
- HVLP or conventional spray gun with appropriate nozzle size (e.g., 0.8mm - 1.4mm).
- Air compressor with moisture separator.
- Abrasive blasting equipment (optional, but recommended for optimal adhesion on metals).
- Degreaser (e.g., acetone, MEK, or specialized Cerakote degreaser).
- Clean, lint-free cloths.
- Personal Protective Equipment (PPE) as outlined in Section 2.
4.2. Surface Preparation Steps
- Żarmar: Disassemble the item to be coated into its individual components.
- Gradasing: Thoroughly degrease all surfaces using a suitable degreaser. Ensure all oils, greases, and contaminants are removed. Repeat if necessary.
- Abrasive Blasting (for Metals): For optimal adhesion on metal substrates, abrasive blast the surface using 100-120 grit aluminum oxide at 80-100 PSI. This creates a profile for the coating to adhere to. Avoid blasting polymers unless specified by the manufacturer.
- Tindif Finali: After blasting (if applicable), re-degrease the surface to remove any blasting media residue or new contaminants. Use clean, lint-free cloths.
- Tnixxif: Ensure the surface is completely dry before application. Use compressed air to blow out any crevices.
4.3. Product Preparation
- Ħawwad sew: CERAKOTE C-SERIES coatings contain solids that will settle. Shake the bottle vigorously for at least 5 minutes before use to ensure a uniform mixture.
- No Catalyst: This C-Series product is air-cured and does not require a catalyst. Do not add any.
- Strain (Optional): For best results, strain the coating through a 100-190 micron filter before pouring into the spray gun cup to prevent clogs.
5. Istruzzjonijiet Operattivi (Applikazzjoni)
Apply CERAKOTE C-SERIES GLACIER BLACK in a controlled environment, maintaining consistent temperature and humidity if possible.
5.1. Spray Gun Settings
- Pressjoni ta' l-Arja: Typically 20-30 PSI at the gun, depending on the gun type and desired atomization. Adjust as needed for a fine, even spray pattern.
- Fluid Control: Adjust to achieve a consistent flow without excessive material.
5.2. Teknika tal-Applikazzjoni
- Hold the spray gun 4-6 inches (10-15 cm) from the surface.
- Apply thin, even coats with overlapping passes. Avoid heavy coats, which can lead to runs or uneven curing.
- Allow 5-10 minutes flash time between coats, or until the surface appears matte and no longer wet.
- Typically, 1-2 coats are sufficient to achieve full coverage and desired film thickness.
- Ensure all surfaces are evenly coated.
5.3. Curing Process
- CERAKOTE C-SERIES GLACIER BLACK is an air-cure coating. It will be dry to the touch within 24 hours at ambient temperatures (60-75°F / 15-24°C).
- Full cure and maximum hardness are achieved over a period of 5-7 days. Handle coated items carefully during this initial curing period.
- Do not expose to harsh chemicals or extreme abrasion until fully cured.
6. Manutenzjoni
Once fully cured, CERAKOTE C-SERIES GLACIER BLACK is highly durable and requires minimal maintenance.
- Tindif: Clean coated surfaces with mild soap and water. Avoid abrasive cleaners or harsh solvents, especially during the initial cure period.
- Protezzjoni: While highly resistant, avoid unnecessary impact or scratching to preserve the finish.
7 Issolvi l-problemi
This section addresses common issues that may arise during application.
| Ħruġ | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| Poor Adhesion / Peeling | Improper surface preparation (oils, grease, inadequate blast profile). | Ensure thorough degreasing and proper abrasive blasting (for metals). Re-clean and re-apply. |
| Uneven Finish / Orange Peel | Incorrect spray gun settings (too much or too little air pressure), improper distance, or too thick coats. | Adjust air pressure and fluid control. Maintain consistent spray distance. Apply thinner, even coats. |
| Runs / Sags | Applying coats too heavily or not allowing sufficient flash time between coats. | Apply thinner coats. Increase flash time between coats. |
| Clogging Spray Gun | Coating not shaken well, or not strained. | Shake product thoroughly before use. Strain coating before pouring into gun. Clean gun immediately after use. |
8. Speċifikazzjonijiet
| Attribut | Dettall |
|---|---|
| Brand | CERAKOTE |
| Numru tal-Mudell | C-7600P |
| Kulur | Glacier Black (C-7600) |
| Tip Finish | Satin |
| Daqs | PINT (16 Fluid Ounces) |
| Tip ta 'żebgħa | Ceramic-based |
| Rakkomandazzjoni tal-wiċċ | Metal, Polymer, More |
| Użu fuq ġewwa/barra | Barra |
| Karatteristika Speċjali | UV Resistant, PFAS Free |
| Huwa Waterproof | Veru |
| Kopertura | Approximately 152.875 square feet (per 16oz pint) |
| Dry Time (to touch) | 24 Sigħat |
| Manifattur | Cerakote |
| Data L-Ewwel Disponibbli | 12 ta’ Diċembru 2022 |
9. Garanzija u Appoġġ
For specific warranty information regarding CERAKOTE C-SERIES GLACIER BLACK (C-7600P), please refer to the official CERAKOTE website or contact their customer support directly. Warranty terms typically cover manufacturing defects and may vary based on purchase location and application.
Appoġġ għall-Klijent:
- For technical assistance, product inquiries, or support, please visit the official CERAKOTE websit.
- Ikkonsulta lill-manifattur website for the most up-to-date contact information and detailed application guides.
