Manwal tal-Istruzzjonijiet tal-Appoġġ tal-Ħajt tat-Tank Kingston Brass CC412

Prodott Overview

The Kingston Brass CC412 Tub Wall Support is a premium accessory designed to provide critical stabilization and reinforcement for tub supply lines. Crafted from solid brass, this support rod ensures durability and reliable performance in your bathroom plumbing system. It is specifically designed to fit over tubing with an outer diameter of 1/2 inch and features a trimmable design for precise installation.

Two polished brass tub wall support rods, one slightly in front of the other, showcasinid-disinn tagħhom.

Image: Two Kingston Brass CC412 Tub Wall Support rods. These rods are made of polished brass and are designed to provide additional support to tub supply lines, ensuring stability and preventing movement.

Karatteristiċi ewlenin:

Fabricated from solid brass for added durability.
Designed to provide additional support to tub supply lines.
Fits supply lines with an O.D. of 1/2 inch.
10-1/8 inch x 3/8 inch Trimmable support rod.
Corrosion-resistant finish.

Setup u Installazzjoni

This section provides general guidelines for the installation of the Kingston Brass CC412 Tub Wall Support. Professional installation is recommended for optimal results and to ensure compliance with local plumbing codes.

Għodda u Materjali Meħtieġa:

Tejp tal-kejl
Lapes jew markatur
Pipe cutter or hacksaw (if trimming is needed)
Screwdriver or drill (for mounting hardware, if applicable)
Appropriate mounting screws/anchors (not included, depending on wall material)

Passi ta' Installazzjoni:

Ipprepara ż-Żona: Ensure the area around the tub supply lines is clean and accessible. Turn off the water supply if necessary for any related plumbing work.
Kejl u Mark: Determine the optimal position for the wall support to provide maximum stability to the tub supply lines. The support rod is trimmable up to 10-1/8 inches. Measure the required length from the wall to the supply line.
Trim the Rod (if necessary): If the measured length is less than 10-1/8 inches, carefully cut the support rod to the desired length using a pipe cutter or hacksaw. Ensure a clean, straight cut.
Attach to Supply Line: Slide the open end of the support rod over the 1/2 inch O.D. tub supply line. The rod should fit snugly.
Waħħal mal-Ħajt: Position the other end of the support rod against the wall. Mark the drilling points for the mounting hardware. Drill pilot holes if required for your wall material and secure the support rod firmly to the wall using appropriate screws and anchors.
Ivverifika l-Istabbiltà: Gently test the tub supply lines to ensure they are now stable and reinforced by the wall support.

Technical diagram showing dimensions of the Kingston Brass CC412 Tub Wall Support, including trimmable length and diameters.

Image: Technical diagram of the Kingston Brass CC412 Wall Support. This diagram illustrates the key dimensions, including the 10-1/8 inch maximum trimmable length and the 1/2 inch inner diameter for the supply line, aiding in precise installation.

Istruzzjonijiet Operattivi

The Kingston Brass CC412 Tub Wall Support is a passive component designed to provide structural reinforcement. It does not have active operating functions. Once properly installed, it continuously supports the tub supply lines, contributing to the overall stability and longevity of your plumbing system.

Ensure that the support remains securely fastened to both the wall and the supply line. Regular visual inspection is recommended to confirm its integrity.

Manutenzjoni

The Kingston Brass CC412 Tub Wall Support requires minimal maintenance due to its durable solid brass construction and corrosion-resistant finish.

Tindif:

Clean the polished brass finish with a soft, damp drapp.
Evita prodotti tat-tindif li joborxu, kimiċi ħarxa, jew pads tal-għorik, għax dawn jistgħu jagħmlu ħsara lill-finitura.
For stubborn spots, a mild soap solution can be used, followed by rinsing with clean water and drying thoroughly.

Spezzjoni:

Periodically inspect the support rod and its mounting points for any signs of looseness, corrosion, or damage.
Ensure the rod remains securely attached to both the supply line and the wall. Tighten mounting screws if necessary.
Address any issues promptly to maintain optimal support for your plumbing.

Issolvi l-problemi

The Kingston Brass CC412 Tub Wall Support is a simple, passive component. Most issues relate to installation or external factors.

Problema	Kawża Possibbli	Soluzzjoni
Supply line still feels unstable after installation.	Rod not securely fastened to wall. Rod not properly gripping supply line. Incorrect rod length or placement.	Ensure mounting screws are tight and appropriate anchors are used for wall material. Verify the supply line O.D. is 1/2 inch. Re-position the rod for a tighter fit. Re-evaluate the installation position and rod length. Adjust or re-trim if necessary.
Finish appears dull or discolored.	Accumulation of soap scum or hard water deposits. Use of abrasive cleaners.	Naddaf b'artab, damp cloth and mild soap solution. Dry thoroughly. Avoid harsh chemicals. If damage is severe, replacement may be necessary.

Speċifikazzjonijiet

Attribut	Dettall
Numru tal-Mudell	CC412
Manifattur	Kingston Brass
Materjal	Brass solidu
Kulur / Finish	Ram illustrat
Dimensjonijiet tal-Prodott	0.75 x 0.75 x 10.13 pulzieri (L x W x H)
Piż tal-oġġett	12.6 uqija
Supply Line O.D. Compatibility	1/2 pulzier
Trimmable Length	Up to 10-1/8 inches
Komponenti Inklużi	Wall Support (1 unit)
Batteriji Meħtieġa	Nru

Garanzija u Appoġġ

Specific warranty details for the Kingston Brass CC412 Tub Wall Support are not provided within this manual. For information regarding product warranty, technical support, or replacement parts, please refer to the official Kingston Brass webis-sit jew ikkuntattja lis-servizz tal-klijenti tagħhom direttament.

Tipikament tista' ssib informazzjoni ta' kuntatt u politiki ta' garanzija fuq il-websajt uffiċjali tal-manifattur. websit: www.kingstonbrass.com

	Istruzzjonijiet ta' Installazzjoni tal-Mili tal-Bagni Kingston Brass CCK266K8 b'Linja tal-Provvista u Valv ta' Waqfien Gwida komprensiva għall-installazzjoni għall-faucet tal-mili tal-banju freestanding Kingston Brass CCK266K8, li tkopri l-partijiet, l-għodda, struzzjonijiet pass pass, u twissijiet essenzjali ta' sigurtà għal setup xieraq.
	Gwida għall-Installazzjoni u l-Manutenzjoni tal-Mili tal-Bagni Kingston Brass Mount Wall Mount Istruzzjonijiet dettaljati għall-installazzjoni u gwida għall-kura għal Kingston Brass Wall Mount Tub Fillers (mudelli bħal CC74T1, CC73T8). Jinkludi lista tal-partijiet, pariri dwar il-manutenzjoni, u twissijiet dwar is-sigurtà.
	Gwida għall-Installazzjoni u l-Kura tal-Faucet Kingston Brass b'Mankijiet Doppji li Jitwaħħal mal-Ħajt Comprehensive guide for installing and maintaining your Kingston Brass Twin Handles Wall Mount Faucet. Includes parts list, step-by-step instructions, and care tips.
	Gwida għall-Installazzjoni u l-Manutenzjoni tal-Faucet Kingston Brass Kaiser KS8127DKL għall-Ħajt Istruzzjonijiet dettaljati għall-installazzjoni, gwida għall-kura, u lista tal-partijiet għall-faucet tal-kamra tal-banju Kingston Brass Kaiser KS8127DKL li jitwaħħal mal-ħajt b'żewġ manki. Jinkludi pariri dwar is-soluzzjoni tal-problemi u l-manutenzjoni.
	Faucet tal-Kċina Kingston Brass GOURMETIER LS862XDL-P: Gwida għall-Installazzjoni, Manutenzjoni, u Garanzija Gwida komprensiva għall-faucet tal-kċina pull-down b'manku wieħed Kingston Brass GOURMETIER LS862XDL-P, inklużi struzzjonijiet dettaljati għall-installazzjoni, pariri dwar il-kura u l-manutenzjoni, soluzzjonijiet għas-soluzzjoni tal-problemi, u informazzjoni dwar garanzija limitata ta' 10 snin.
	Gwida għall-Installazzjoni u l-Kura tal-Faucet Kingston Brass b'Mankijiet Doppji li Jitwaħħal mal-Ħajt Gwida komprensiva għall-installazzjoni u l-manutenzjoni tal-Kingston Brass Twin Handles Wall Mount Faucet. Tinkludi lista tal-partijiet, partijiet ta' sostituzzjoni, struzzjonijiet ta' installazzjoni pass pass, u pariri essenzjali għall-kura għal ħajja itwal.

Kingston Brass CC412