AUTOONE LED Tail Light Assembly User Manual

1. Prodott Aktarview

This manual provides detailed instructions for the installation, operation, and maintenance of your AUTOONE LED Tail Light Assembly. Designed specifically for 2009-2014 Ford F-150 models, these upgraded taillights enhance vehicle visibility and appearance.

Ditta: AUTOONE

Mudell: F150 LED Tail Light

Vetturi Kompatibbli: 2009, 2010, 2011, 2012, 2013, 2014 Ford F-150

Numri OE: BL3Z13404B, BL3Z13405B, FO2818143, FO2819143

2. Karatteristiċi ewlenin

• Upgraded LED Lighting: All halogen bulbs are replaced with brighter, clearer LED bulbs for improved visibility and a distinct vehicle appearance. Includes LEDs for reversing lights, brake lights, turn signals, and side markers.
• Kostruzzjoni Durabbli: Manufactured with high-strength ABS and UV-protected PC materials to prevent aging from sun exposure and maintain light transmission.
• Reżistenza għat-temp: IP67 waterproof, dustproof, impact resistant, and corrosion resistant for long-lasting performance in various conditions.
• Tajbin Dirett: Designed for direct replacement without requiring drilling, cutting, or modifications.

3. Kontenut tal-Pakkett

• 1 x F150 LED Tail Light Assembly (Driver Side)
• 1 x F150 LED Tail Light Assembly (Passenger Side)
• Mounting Hardware (if applicable, refer to installation video)

Image: Pair of AUTOONE LED Tail Light Assemblies (Clear Lens).

4. Gwida għall-Installazzjoni

Installation is a direct replacement process. No drilling or cutting is required. For optimal results, it is recommended to test the lights before fully securing them.

4.1. Għodod Meħtieġa

• 10mm Socket Wrench or Phillips Head Screwdriver (depending on vehicle model)
• Pliers (for resistor mounting, if applicable)

4.2. Installazzjoni Pass Pass

1. Open Tailgate: Lower your truck's tailgate to access the tail light assembly.
2. Neħħi l-Qafliet: Locate and remove the two 10mm bolts or screws holding the factory tail light in place. These are typically found on the inside edge of the tail light assembly.
3. Detach Factory Tail Light: Gently pull the tail light assembly straight back, away from the truck body. It may be held by plastic clips that will release with a firm pull.
4. Skonnettja l-Wiring: Carefully disconnect the wiring harnesses from the factory tail light bulbs. For the reverse light, you will need to transfer the factory bulb and socket to the new LED assembly.
5. Prepare New LED Tail Light:
   • Connect the new LED tail light's wiring harnesses to the vehicle's existing wiring.
   • For the reverse light, insert the factory reverse light bulb and socket into the designated opening on the new LED tail light assembly.
   • If load resistors are included and not pre-mounted, secure them to a metal surface away from plastic components to dissipate heat.
6. Funzjonalità tat-Test: Before fully securing, temporarily position the new LED tail light and test all functions: running lights, brake lights, turn signals, and reverse lights. Ensure all lights operate correctly. If the reverse light does not work, try flipping the pins in the reverse light plug.
7. Secure New LED Tail Light: Align the new LED tail light with the mounting points on the truck body. Push it firmly into place until the plastic clips engage. Reinstall the two 10mm bolts or screws removed earlier.
8. Irrepeti għan-Naħa l-Oħra: Follow the same steps for the opposite side tail light.

4.3. Għajnuna Viżwali għall-Installazzjoni

For a visual walkthrough of the installation process, please refer to the following videos:

Image: Demonstrating the easy installation process of the tail light.

5. Operazzjoni

The AUTOONE LED Tail Light Assembly features multiple lighting modes for enhanced safety and visibility:

• Dwal tat-Tmexxija: Illuminate when headlights are on, providing continuous rear visibility.
• Dwal tal-Brejkijiet: Activate when the brake pedal is pressed, signaling deceleration.
• Sinjali tad-dawran: Flash to indicate a turn or lane change.
• Dwal ta' Reversa: Bright white illumination when the vehicle is in reverse.

Image: Visual display of driving light, brake light, reversing light, and turn signal modes.

6. Manutenzjoni

The AUTOONE LED Tail Light Assembly is designed for durability and minimal maintenance. Regular cleaning with mild soap and water is recommended to maintain clarity and appearance. Avoid abrasive cleaners or harsh chemicals that could damage the lens material.

Image: Illustrates the IP67 waterproof rating, protecting against sand, rain, snow, and dust.

7 Issolvi l-problemi

• Dwal Mhux Jaħdmu:
  • Ensure all wiring harnesses are securely connected.
  • Check vehicle fuses related to tail lights.
• Reverse Light Not Working:
  • Verify the factory reverse bulb is correctly inserted into the new assembly.
  • If the bulb is correctly inserted and still not working, try removing the reverse light plug and flipping the pins before reinserting.
• Hyper-flashing Turn Signals:
  • Ensure any included load resistors are properly installed and securely mounted to a metal surface.

8. Speċifikazzjonijiet

9. Garanzija u Appoġġ

Jekk jogħġbok irreferi għall-imballaġġ tal-prodott jew għall-informazzjoni uffiċjali tal-manifattur. website for specific warranty information. For technical support or inquiries, contact AUTOONE customer service.