1. Prodott Aktarview
The PWAYTEK HDMI Over Ethernet Extender allows for the transmission of HDMI signals over long distances using a single Cat5e/6/7 Ethernet cable. It supports 1080P@60Hz resolution, Full HD 3D, and includes features such as local loop out, EDID management, IR control, and Power Over Cable (POC) functionality for simplified installation.
Karatteristiċi ewlenin:
- Trażmissjoni Estiża: Achieves 60m/196ft with Cat6/7 and 40m/130ft with Cat5e for superior audio and video quality.
- Viżwali ta' Definizzjoni Għolja: Supports 1080P@60Hz and Full HD 3D for an immersive viewing esperjenza.
- Kontroll IR: Enables remote control of the signal source (20-60KHz).
- Local Loop Out: Transmitter includes an HDMI output port for local monitoring.
- Unilateral Power Supply (POC): Powers both transmitter and receiver via a single Ethernet cable, eliminating the need for a power adapter at the receiver end.
- Kostruzzjoni Durabbli: Full metal housing for enhanced durability.
2. Kontenut tal-Pakkett
Iċċekkja li l-oġġetti kollha elenkati hawn taħt huma inklużi fil-pakkett tiegħek.
Image: Contents of the PWAYTEK HDMI Extender package.
- 1x HDMI Extender Transmitter
- 1x HDMI Extender Receiver
- 1x Power Adapter (for Transmitter)
- 2x IR Cables (1x IR Blaster, 1x IR Receiver)
- 1x Manwal għall-Utent
3. Istruzzjonijiet ta' Setup
Follow these steps to set up your PWAYTEK HDMI Extender.
3.1 Konnessjoni tat-Trasmettitur (TX)
Immaġni: Minn quddiem u mill-ġenb view of the Transmitter unit.
- Connect your HDMI source device (e.g., PC, DVD player, set-top box) to the HDMI-IN port on the Transmitter unit using an HDMI cable.
- If local monitoring is desired, connect a local display (e.g., TV, monitor) to the HDMI OUT (Loop Out) port on the Transmitter unit using an HDMI cable.
- Connect one end of a Cat5e/6/7 Ethernet cable to the UTP port fuq l-unità tat-Trasmettitur.
- If using IR control, connect the IR Blaster cable to the IR OUT port on the Transmitter and position the IR emitter near the IR sensor of your source device.
3.2 Konnessjoni tar-Riċevitur (RX)
Image: Typical connection diagram for the HDMI Extender.
- Connect the other end of the Cat5e/6/7 Ethernet cable from the Transmitter to the UTP port fuq l-unità tar-Riċevitur.
- Connect your remote display (e.g., TV, projector) to the HDMI OUT port on the Receiver unit using an HDMI cable.
- If using IR control, connect the IR Receiver cable to the IR IN port on the Receiver and position the IR receiver to face your remote control.
3.3 It-Tħaddim tal-Apparat
- Qabbad l-adapter tal-enerġija pprovdut mal- DC 5V port fuq l-unità tat-Trasmettitur.
- Plug the power adapter into a wall outlet. Due to POC (Power Over Cable) functionality, the Receiver unit will be powered automatically through the Ethernet cable from the Transmitter.
- Ivverifika li l- PWR u STA (Status) indicator lights on both the Transmitter and Receiver units are illuminated, indicating a successful connection and power supply.
4. Istruzzjonijiet Operattivi
4.1 Distance Selection Switch
The Receiver unit features a switch to optimize performance based on the Ethernet cable length:
- Issettja l-iswiċċ għal '30m' for cable lengths up to 30 meters (approximately 98 feet).
- Issettja l-iswiċċ għal '50m' for cable lengths between 30 meters and 60 meters (approximately 196 feet).
Ensure the switch setting matches your cable length for optimal signal quality.
4.2 Local Loop Out Function
Image: Illustration of the local loop out functionality.
The HDMI OUT port on the Transmitter allows you to connect a local display. This is useful for monitoring the source content without needing to go to the remote display location.
4.3 Kontroll IR
Image: Setup for IR remote control.
The IR control feature allows you to use your source device's remote control from the remote display location. Point your remote at the IR Receiver connected to the Receiver unit. The signal will be transmitted via the Ethernet cable to the IR Blaster connected to the Transmitter unit, which then controls your source device.
5. Manutenzjoni
- Keep the device in a cool, dry place away from direct sunlight and heat sources.
- Naddaf l-apparat b'ċarruta ratba u niexfa. Tużax prodotti tat-tindif likwidi jew aerosol.
- Żgura ventilazzjoni xierqa madwar l-unitajiet biex tevita li jisħnu żżejjed.
- Avoid bending or crimping the HDMI and Ethernet cables excessively.
6 Issolvi l-problemi
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| No picture on the remote display. | Loose cable connections, incorrect power, incompatible resolution, incorrect distance switch setting. | Check all HDMI and Ethernet cable connections. Ensure the power adapter is connected to the Transmitter and plugged in. Verify the PWR and STA lights are on. Adjust the distance switch on the Receiver to match your cable length. Ensure your source and display support 1080P@60Hz. Try a different HDMI cable. |
| Flickering or intermittent signal. | Poor quality Ethernet cable, excessive cable length, interference, incorrect distance switch setting. | Use a high-quality Cat6 or Cat7 Ethernet cable. Ensure the cable length is within the specified limits (60m for Cat6/7, 40m for Cat5e). Adjust the distance switch on the Receiver. Avoid running the Ethernet cable near strong electrical interference sources. |
| Il-kontroll IR mhux qed jaħdem. | IR cables incorrectly connected, IR emitter/receiver not properly positioned. | Ensure the IR Blaster is connected to the Transmitter's IR OUT and the IR Receiver to the Receiver's IR IN. Position the IR Blaster directly over the source device's IR sensor. Ensure the IR Receiver is facing your remote control. |
| No local loop out display. | HDMI cable issue, local display input selection. | Check the HDMI cable connecting the Transmitter's HDMI OUT to the local display. Ensure the local display is set to the correct HDMI input. |
7. Speċifikazzjonijiet
| Karatteristika | Dettall |
|---|---|
| Brand | PWAYTEK |
| Mudell | B0CDQ48VVJ |
| Tip ta' Konnettur | HDMI |
| Distanza tat-Trażmissjoni | Up to 60m (196ft) with Cat6/7; 40m (130ft) with Cat5e |
| Riżoluzzjoni Appoġġjata | 1080P@60Hz, Full HD 3D |
| IR Control Frequency | 20-60KHz |
| Provvista tal-Enerġija | Unilateral Power Supply (POC) via Transmitter |
| Materjal tad-Djar | Metall |
| Piż tal-oġġett | 13.4 uqija |
| Dimensjonijiet tal-Pakkett | 5.55 x 4.33 x 2.52 pulzieri |
8. Garanzija u Appoġġ
PWAYTEK products are designed for reliability and performance. For any technical assistance or warranty inquiries, please refer to the contact information provided in your product packaging or visit the official PWAYTEK websit. Żomm l-irċevuta tax-xiri tiegħek għall-validazzjoni tal-garanzija.
