Introduzzjoni
Thank you for choosing the Hobbywing Skywalker V2 50A Brushless Flight Controller (ESC). This ESC is designed for RC aircraft, offering reliable performance and advanced features. This manual provides essential information for proper installation, operation, and maintenance to ensure safe and optimal use of your product.
Linji Gwida dwar is-Sigurtà
Please read and understand all safety instructions before operating the ESC. Failure to do so may result in damage to the product, property, or personal injury.
- Always connect the ESC to the motor and battery correctly, observing polarity.
- Kun żgur li l-konnessjonijiet kollha huma sikuri biex tevita short circuits.
- Żomm l-ESC 'il bogħod mill-umdità, it-trab, u temperaturi estremi.
- Teċċedix il-kurrent u l-volum speċifikatitage klassifikazzjonijiet.
- Always disconnect the battery after use.
- Perform initial setup and throttle calibration with the propeller removed for safety.
Prodott Overview
The Hobbywing Skywalker V2 50A ESC is an advanced brushless flight controller featuring a 32-bit microprocessor for enhanced throttle response and reduced operating temperature. It supports 3-4S LiPo batteries and includes a 5V@5A SBEC. The ESC is equipped with DEO (Driving Efficiency Optimization) technology and offers various programmable braking modes and protection mechanisms.
This image displays the Hobbywing Skywalker V2 50A Brushless Flight Controller. It is a compact, black-sleeved electronic speed controller with various wires extending from both ends. The label on the ESC clearly indicates 'HOBBYWING SKYWALKER 50A V2-UBEC', '3-4S Lipo SBEC 5V@5A', and regulatory marks like 'RoHS FC CE'. The wires are color-coded for different connections, including thicker black wires for motor connections and thinner red, yellow, and white wires for signal and power input.
Speċifikazzjonijiet Tekniċi
| Karatteristika | Valur |
|---|---|
| Mudell | Skywalker V2 50A |
| Dimensjonijiet (L x W x H) | 6 x 2.5 x 0.8 ċm |
| Piż | 36 gramma |
| Kurrent Kontinwu | 50A |
| Max Current (Burst) | 70A |
| Ċelloli LiPo | 3-4S |
| SBEC Output | 5V@5A |
| Mikroproċessur | 32-bit (up to 96 MHz) |
| Materjal Prinċipali | Plastik |
| Kulur | Iswed |
| Referenza tal-Manifattur | HW80060442 |
Kontenut tal-Pakkett
Il-pakkett tipikament jinkludi l-oġġetti li ġejjin:
- Hobbywing Skywalker V2 50A Brushless Flight Controller
- LED Program Box (H.W30501003) or compatible transmitter for programming (may be sold separately)
Setup u Installazzjoni
Wiring
Proper wiring is crucial for the safe and correct operation of your ESC. Refer to the diagram below for typical connections. Always ensure correct polarity.
- Konnessjoni tal-Mutur: Connect the three thicker black wires from the ESC to the three motor wires. The order may affect motor rotation direction; swap any two wires if the motor spins in the wrong direction.
- Konnessjoni tal-batterija: Connect the red (+) and black (-) wires from the ESC to your LiPo battery, ensuring correct polarity.
- Konnessjoni tar-riċevitur: Connect the signal cable (usually a three-wire servo connector) from the ESC to the throttle channel of your RC receiver.
Konfigurazzjoni Inizjali
Before first flight, it is recommended to perform throttle range calibration and configure any desired programmable parameters.
Operazzjoni
Kalibrazzjoni tal-Medda tat-Throttle
This procedure ensures that the ESC correctly recognizes the full throttle range from your transmitter.
- Turn on your transmitter and set the throttle stick to its maximum position.
- Connect the battery to the ESC. The motor will emit a series of beeps.
- When you hear a specific tone (usually two short beeps), move the throttle stick to its minimum position.
- L-ESC se joħroġ serje oħra ta' beeps, li jikkonferma li l-firxa tat-throttle ġiet mgħallma.
- Disconnect the battery. The calibration is complete.
L-ipprogrammar tal-ESC
The Skywalker V2 50A ESC offers various programmable parameters to fine-tune its performance. These can be adjusted using a Hobbywing LED Program Box (H.W30501003) or through your transmitter.
Programmable features include:
- Brake Type and Brake Force
- Cutoff Voltage (for LiPo cell protection)
- LiPo Cell Count Setting
- Modalità tal-Istartjar
- Modalità Fittex
- Iż-żmien
- Active Freewheel
Refer to the specific instructions provided with your LED Program Box or transmitter for detailed programming steps.
Manutenzjoni
Regular maintenance helps prolong the life and ensure the reliability of your ESC.
- Keep the ESC clean and free from dirt, dust, and debris.
- Inspect all wires and connectors periodically for signs of wear, damage, or corrosion.
- Ensure adequate airflow around the ESC during operation to prevent overheating.
- Store the ESC in a dry, cool place when not in use.
Issolvi l-problemi
If you encounter issues with your ESC, refer to the table below for common problems and solutions.
| Problema | Soluzzjoni Possibbli |
|---|---|
| Motor does not start or stutters | Check battery connection and charge level. Verify motor wiring. Perform throttle calibration. |
| L-ESC iżżejjed | Ensure adequate cooling. Check for motor overload or incorrect timing settings. |
| Il-mutur jimxi fid-direzzjoni żbaljata | Ibdel kwalunkwe tnejn mit-tliet wajers tal-mutur imqabbda mal-ESC. |
| No response from ESC | Check receiver connection and power. Ensure transmitter is on and bound. |
| Sudden power loss during flight | Batterija voltage cutoff activated. Check battery health and charge. |
Garanzija u Appoġġ
Hobbywing products are manufactured to high-quality standards. This product typically comes with a 1-year availability for spare parts. For warranty claims or technical support, please contact your retailer or visit the official Hobbywing websit għall-għajnuna.
