Retoo Thermostat Plug with Temperature Sensor, Model E634 - Instruction Manual

1. Introduzzjoni

This manual provides detailed instructions for the safe and efficient operation of your Retoo Thermostat Plug, Model E634. This device is designed to precisely control temperature for various applications, including terrariums, aquariums, greenhouses, and home heating/cooling systems, by regulating the power supply to connected appliances based on a set temperature range. Please read this manual thoroughly before use and retain it for future reference.

Figure 1: Retoo Thermostat Plug with integrated display and external temperature sensor.

2. Prodott Aktarview

The Retoo Thermostat Plug features a clear digital display, intuitive controls, and an external temperature probe for accurate readings. It supports both heating and cooling modes and includes a timer function for scheduled operation.

2.1 Komponenti

• Thermostat Plug Unit
• External Temperature Sensor Probe (wired)
• Manwal ta 'Istruzzjoni (dan id-dokument)

Figura 2: Quddiem view of the thermostat plug, highlighting the display and control buttons (MODE, SET, UP, DOWN).

Figura 3: Wara view of the thermostat plug, showing the power prongs and product specifications label.

3. Setup

1. Spakkja l-Apparat: Carefully remove the thermostat plug and its components from the packaging.
2. Qabbad is-Sensor: Ensure the external temperature sensor probe is securely connected to the thermostat unit. The probe is typically pre-attached.
3. Ipplaggja l-Enerġija: Insert the thermostat plug into a standard European grounded wall socket (250V). The display will illuminate.
4. Pożizzjona s-Sensor: Place the temperature sensor probe in the area where you wish to measure and control the temperature. Ensure it is not directly exposed to heat sources or drafts that could skew readings.
5. Qabbad Appliance: Plug the appliance you wish to control (e.g., heater, fan, lamp) into the socket on the front of the thermostat plug.

Figure 4: The thermostat plug connected to a wall outlet, ready for use.

4. Istruzzjonijiet Operattivi

4.1 Display Overview

The digital display shows the measured temperature, set start temperature, set stop temperature, and timer information. The unit can operate in both heating and cooling modes.

Figura 5: Eżample display showing current temperature, and programmed ON/OFF temperatures for an appliance.

4.2 Setting Temperature Parameters

1. Agħfas il- SET button once to enter temperature setting mode. The "Start Temperature" value will flash.
2. Uża l- UP u 'L isfel buttons to adjust the desired start temperature. This is the temperature at which the connected appliance will turn ON.
3. Agħfas SET again. The "Stop Temperature" value will flash.
4. Uża l- UP u 'L isfel buttons to adjust the desired stop temperature. This is the temperature at which the connected appliance will turn OFF.
5. Agħfas SET a third time to confirm settings and exit. The device will now operate based on your set parameters.

Nota: If the start temperature is set higher than the stop temperature, the device will operate in mod tat-tkessiħ (e.g., for a fan). If the start temperature is set lower than the stop temperature, it will operate in mod tat-tisħin (e.g., for a heater).

4.3 Timer Function (Cycle Timer)

The thermostat includes a cycle timer function, indicated by "CD ON" and "CD OFF" on the display. This allows for scheduled on/off periods independent of temperature control, or in conjunction with it.

1. Agħfas il- MODALITÀ button repeatedly until "CYCLE TIMER" or "CD ON/OFF" settings are displayed.
2. Uża l- SET button to cycle through setting "CD ON" (duration the appliance is on) and "CD OFF" (duration the appliance is off).
3. Uża l- UP u 'L isfel buttons to adjust the hours and minutes for each cycle.
4. Agħfas MODALITÀ to save and exit the timer settings.

Nota: Refer to the specific display indicators for "CD ON" and "CD OFF" to ensure correct timer programming. The timer function can be used for applications requiring periodic operation, such as ventilation or lighting cycles.

4.4 Ir-Resetjar tal-Apparat

To reset the device to factory settings, locate the small reset button (often a pinhole) between the SET u UP buttons. Use a thin, pointed object (like a paperclip) to press and hold this button for a few seconds until the display resets.

5. Manutenzjoni

• Tindif: Disconnect the device from power before cleaning. Wipe the surface with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.
• Kura tas-Sensor: Keep the temperature sensor probe clean and free from debris. Avoid bending or damaging the sensor cable.
• Ħażna: When not in use, store the thermostat plug in a cool, dry place, away from direct sunlight and extreme temperatures.

6 Issolvi l-problemi

7. Speċifikazzjonijiet

• Ditta: Irretoo
• Numru tal-Mudell: E634
• Voltage: 100-250VAC (110V, 230V compatible)
• Tagħbija Massima: 16A(2), 3680W
• Firxa tat-Temperatura: -40°C sa +120°C
• Eżattezza tal-Kontroll tat-Temperatura: ±1%
• Preċiżjoni tal-ħin: Max 10 minuta
• Dimensjonijiet (L x W x H): 12 x 7.6 x 5.8 ċm
• Piż tal-oġġett: 166 g
• Teknoloġija tal-Konnettività: Bil-fili
• Karatteristika Speċjali: Wiri tat-Temperatura

Figure 6: Technical dimensions of the thermostat plug and sensor cable.

8. Garanzija u Appoġġ

For warranty information or technical support, please refer to the retailer's return policy or contact Retoo customer service directly. Details may be available on the product packaging or the official Retoo websit.

Appoġġ onlajn: Żur il- Retoo Brand Store on Amazon għal aktar informazzjoni dwar il-prodott u riżorsi ta' appoġġ.