KEMIMOTO UTV Side Mirrors Instruction Manual

Introduzzjoni

This manual provides detailed instructions for the installation, operation, and maintenance of your KEMIMOTO UTV Side Mirrors. Please read this manual thoroughly before installation and use to ensure proper function and safety. These mirrors are designed for UTVs with 1.65-2 inch roll bars, offering multi-adjustment and a convex mirror for enhanced visibility.

Prodott Overview

The KEMIMOTO UTV Side Mirrors are constructed from high-impact ABS plastic and stainless steel bolts, designed to withstand rough terrain and reduce vibration. They feature a break-away design to prevent damage from obstacles and offer multiple adjustment methods for optimal viewangoli.

Kontenut tal-Pakkett:

• 1 Pair KEMIMOTO UTV Side Mirrors
• All necessary mounting hardware (screws, nuts, Allen wrenches)
• Rubber mats for secure fit and noise reduction

Kompatibilità

These KEMIMOTO UTV Side Mirrors are compatible with 1.65"-2" roll bars. They fit a wide range of UTV models, including but not limited to:

• Polaris RZR (except 170)
• Pijunier
• Can-Am Maverick X3
• Teryx
• Talon
• Gator
• ZFORCE 850, 900, 1000

Note: Not compatible with 2015-2025 Ranger models featuring a Pro-Fit cage. Only fits round bar cages.

Setup u Installazzjoni

Installation of the KEMIMOTO UTV Side Mirrors is designed to be straightforward. Follow these steps for a secure fit:

1. Prepare the Clamps: Identify the correct size rubber mats for your roll bar (1.65"-2"). Place the rubber mats inside the C-clamps to ensure a snug fit and prevent slippage.
2. Poġġi l-Clamps: Iftaħ is-C-clamps and place them on your UTV's roll bar at your desired mirror location. Ensure the clamps are securely seated.
3. Attach the Mirror Assembly: Align the mirror assembly with the installed clamps. Insert the provided screws through the mirror's base and into the clamps.
4. Issikka sew: Use the provided Allen wrenches to tighten the screws. Ensure the mirrors are firmly attached to the roll bar. Do not overtighten to avoid damaging the clamps or roll bar.
5. Aġġustament Finali: After initial tightening, adjust the mirror angle as needed. The mirrors can be adjusted after installation, eliminating the need for repeated installation.

Vidjo ta 'installazzjoni:

Operazzjoni u Użu

The KEMIMOTO UTV Side Mirrors are designed for optimal visibility and durability during off-road adventures.

Metodi ta' Aġġustament:

These SXS side mirrors offer three adjustable methods to customize your viewangolu tal-ing:

• Mirror Face Adjustment: The mirror face itself can be tilted and rotated to achieve the desired rear view.
• Ball Pivot Design: A 360° adjustable ball pivot allows for fine-tuning the mirror's position.
• Mounting Arm Adjustment: The arm connecting the mirror to the clamp can also be adjusted to extend or retract the mirror's reach.

Break Away Feature:

The mirrors incorporate a "break away" design, allowing them to fold inward upon impact with obstacles like tree limbs. This feature helps prevent damage to the mirrors and allows them to be reset to their original position without manual readjustment if the impact is less than 90 degrees. For impacts greater than 90 degrees, manual readjustment may be required.

Vidjows tal-Operazzjoni:

Manutenzjoni

To ensure the longevity and optimal performance of your KEMIMOTO UTV Side Mirrors, regular maintenance is recommended:

• Tindif: Clean the mirror surfaces and housing regularly with a soft cloth and mild soap and water. Avoid abrasive cleaners that could scratch the mirror or plastic.
• Iċċekkja l-issikkar: Periodically inspect all mounting screws and adjustment points. Tighten any loose screws using the provided Allen wrenches to prevent vibration and ensure the mirrors remain in position.
• Spezzjona għal Ħsara: After off-road use, check the mirrors for any signs of damage to the housing, glass, or mounting brackets. Replace any damaged components promptly.

Issolvi l-problemi

If you encounter any issues with your KEMIMOTO UTV Side Mirrors, refer to the following common troubleshooting tips:

• Mirror Shaking/Vibration: Ensure all mounting screws are tightened securely. The included rubber mats should help reduce vibration. If shaking persists, re-check the fitment of the clamps on the roll bar.
• Difficulty Adjusting Mirror: If the mirror is too stiff or too loose to adjust, use the appropriate Allen wrench to slightly loosen or tighten the adjustment screws on the ball pivot or mounting arm until the desired tension is achieved.
• Il-mera Ma Tibqax fil-Pożizzjoni: This is typically due to insufficient tightening of the adjustment screws. Tighten the screws at the ball pivot and mounting arm until the mirror holds its position firmly.

Speċifikazzjonijiet

Garanzija u Appoġġ

For warranty information or technical support regarding your KEMIMOTO UTV Side Mirrors, please refer to the contact information provided with your purchase or visit the official KEMIMOTO websit. Żomm il-prova tax-xiri tiegħek għal kwalunkwe talba ta' garanzija.