1. Introduzzjoni
This manual provides detailed instructions for the safe and efficient use of your HEATIT ET-24 Freeze Thermostatically Controlled Outlet. Please read this manual thoroughly before operation and retain it for future reference.
2. Informazzjoni dwar is-Sigurtà
Observe the following safety guidelines to ensure proper operation and prevent hazards:
- This device is intended for use in dry locations only. Do not expose to water or excessive moisture.
- Maximum load capacity is 15 Amps. Do not exceed this rating.
- Il-prodott huwa ETL approvat, ensuring compliance with safety standards.
- Always ensure the device is securely plugged into a functional electrical outlet.
- To prevent risks of overheating or fire, always select heating cables and related products that have appropriate safety certifications and product liability insurance.
3. Karatteristiċi tal-prodott
The HEATIT ET-24 is designed for automatic temperature control to protect against freezing:
- Kontroll tat-termostat: Automatically energizes connected devices when temperatures drop.
- Dawl Indikatur Intelliġenti: A yellow light illuminates when the temperature is below 38°F (3°C) and the outlet is actively supplying power.
- Operazzjoni Awtomatika: Turns on below 38°F (3°C) and turns off at approximately 50°F (10°C).
- Iffrankar tal-Enerġija: Activates only when necessary, reducing energy consumption.
- Installazzjoni faċli: Simple plug-and-play design.
- Applikazzjonijiet versatili: Suitable for 120 VAC electric heaters, engine heaters, pipe heat tape, roof heating cables, and similar applications.
4. Setup u Installazzjoni
Follow these steps to set up your HEATIT ET-24 outlet:
- Ensure the installation location is dry and protected from moisture.
- Plug the HEATIT ET-24 directly into a standard 120 VAC electrical wall outlet.
- Connect your heating device (e.g., heat tape, electric heater) to one or both of the outlets on the HEATIT ET-24. The unit supports both 2-pin and 3-pin plugs simultaneously.
- Test Inizjali: To verify functionality upon receipt, place the unit in a freezer for approximately 45 minutes to reset its internal thermostat. After removing it from the freezer, plug it into a wall outlet. The yellow indicator light should illuminate, confirming the thermostat is active and the outlet is energized.
5. Istruzzjonijiet Operattivi
The HEATIT ET-24 operates automatically based on ambient temperature:
- Turn-on Temperature: The outlet will energize (turn on) when the ambient temperature drops below 38°F (3°C).
- Turn-off Temperature: The outlet will de-energize (turn off) when the ambient temperature rises to approximately 50°F (10°C).
- Dawl Indikatur: A yellow indicator light will illuminate when the temperature is below 38°F (3°C) and the outlet is actively supplying power to the connected device. This light confirms the thermostat is working.
6. Manutenzjoni
Biex tiżgura l-lonġevità u l-prestazzjoni ottimali tat-tagħmir tiegħek:
- Żomm l-apparat nadif u ħieles mit-trab u l-fdalijiet. Uża drapp niexef għat-tindif.
- Do not attempt to open or repair the unit. Refer to qualified personnel for service.
- Store in a dry environment when not in use, especially during warmer seasons.
7 Issolvi l-problemi
If you encounter issues with your HEATIT ET-24, consider the following:
- Device not turning on at low temperatures:
- Ensure the unit is securely plugged into a functional electrical outlet.
- Ivverifika li l-apparat imqabbad qed jaħdem sew meta jiġi pplaggjat direttament f'sokit standard.
- Perform a reset: Place the unit in a freezer for approximately 45 minutes. After removing, plug it into a wall outlet. The indicator light should turn on if the ambient temperature is below 38°F (3°C).
- Indicator light is on, but connected appliance is not heating:
- The indicator light confirms the outlet is energized. Check the connected appliance itself for proper function and ensure it is designed to operate at the current temperature.
- Device not turning off at higher temperatures:
- Ensure the ambient temperature has risen above 50°F (10°C). The device has a hysteresis to prevent rapid cycling.
- If the issue persists, perform a reset as described above.
8. Speċifikazzjonijiet
| Karatteristika | Dettall |
|---|---|
| Brand | SĦANA |
| Isem tal-Mudell | ET-24 |
| Dimensjonijiet tal-Prodott (P x W x H) | 1.38" x 3.78" x 1.06" |
| Tip ta' Kontrollur | Kontroll Termostatiku Awtomatiku |
| Kulur | Isfar |
| Tip ta' Kontroll tat-Temperatura | Awtomatiku |
| Sors tal-Enerġija | Corded Elettriku |
| Voltage | 120 Volts |
| Max. Kurrent tat-Tagħbija | 15 Amps |
| Max. Qawwa tat-Tagħbija | 1800 Watts |
| Turn-on Temperature | Taħt 38°F (3°C) |
| Turn-off Temperature | Madwar 50°F (10°C) |
| Materjal | PC + ABS |
| Piż tal-oġġett | 2.99 uqija |
| Ċertifikazzjonijiet | ETL Approvat |
9. Garanzija u Appoġġ
This product is designed for reliability and safety. While specific warranty details are not provided in this manual, HEATIT products are typically backed by quality assurance.
Politika ta' Ritorn: Standard return policies apply, typically allowing returns within 30 days for refund or replacement, as per the point of purchase.
Responsabbiltà tal-Prodott: To ensure safety, always use heating cables and related products that carry appropriate safety certifications and product liability insurance.
For support, please refer to the official HEATIT store or contact customer service through your point of purchase.
