Avallon AIMG151GSSILH Manwal ta 'Istruzzjoni tal-Maker tas-Silġ

Introduzzjoni

This manual provides essential information for the safe and efficient operation of your Avallon AIMG151GSSILH 15-inch built-in/free-standing ice maker. This unit is designed to produce uniquely shaped, clear gourmet ice cubes that melt slowly, enhancing your beverages. It features rapid ice production, capable of producing up to 56 lbs. of ice in 24 hours, with a storage capacity of 26 lbs. The door is constructed from high-quality 304 stainless steel and includes a convenient wash mode for easy maintenance.

Informazzjoni dwar is-Sigurtà

WARNING: Risk of Electric Shock. Disconnect Power Before Servicing Unit.

Please read all instructions carefully before using the appliance to reduce the risk of fire, electric shock, or injury. This ice maker is ETL and UL listed, ensuring it meets safety standards. It is approved for outdoor use, but proper installation and electrical precautions must be observed. This product is not a freezer and will not keep stored items frozen indefinitely.

Propożizzjoni 65 Twissija:

Dan il-prodott jista’ jesponik għal kimiċi inkluż Di(2-ethylhexyl)phthalate (DEHP), li huwa magħruf mill-Istat ta’ Kalifornja li jikkawża kanċer u difetti fit-twelid jew ħsara riproduttiva oħra. Għal aktar informazzjoni mur fuq www.P65Warnings.ca.gov.

Setup

Unboxing u Komponenti

Carefully remove the ice maker from its packaging. Ensure all components are present:

• Avallon AIMG151GSSILH Ice Maker Unit
• Scoop tas-Silġ
• Water Inlet Pipe (1/4" size)
• Ixxotta pajp
• Door Handle and Fixed Screws

Tqegħid u Dimensjonijiet

The Avallon AIMG151GSSILH can be installed as a built-in unit or as a free-standing appliance. Ensure adequate ventilation, especially for built-in installations, as the unit features front heat dissipation. The dimensions are: Depth: 23-1/4"; Width: 14-15/16"; Height: 33-3/4".

Figure 1: Avallon AIMG151GSSILH Ice Maker with labeled dimensions (Depth: 22.63", Width: 14.94", Height: 33.75").

Figure 2: Avallon AIMG151GSSILH Ice Maker installed as a built-in unit under a kitchen counter.

Installazzjoni tal-Manku tal-Bieb

Biex tinstalla l-manku tal-bieb:

1. Remove the door handle and fixed screws from the packaging.
2. Unscrew the secret screw at the bottom of the door handle with the hex wrench to a certain extent to prevent it from not fitting during installation.
3. Peel off the protective film on the door surface to reveal the screw holes at the top.
4. Align the fixed screws of the door handle vertically with the holes on the door.
5. Tighten them with a crosshead screwdriver.
6. Align the door handle with the fixed screws, push it in, and ensure it is fully seated.
7. Tighten the bottom security screws.
8. After securing, pull the door handle to ensure it does not become loose.

Water Inlet Pipe Installation

Connect the 1/4" water inlet pipe to the ice maker:

1. Remove the clip from the water intake port at the back of the ice maker.
2. Align the water pipe with the inlet and push it firmly into place.
3. Reattach the clip that was removed earlier to secure the pipe.
4. Gently pull the water pipe outward to ensure it is securely fixed.
5. To replace or remove the water inlet pipe, first remove the buckle, then push the water inlet pipe inward to remove and replace it.

Installazzjoni tal-Manka tal-Ixxotta

Proper drain hose installation is crucial for efficient water discharge:

1. Remove the waterproof plug from the drain port at the back of the ice maker.
2. Align the larger end of the drain hose with the drain port and push it in firmly.
3. Ensure the entire drain pipe is positioned lower than the water outlet on the ice maker, as the unit relies on gravity drainage. If the drain hose is too high, water cannot drain smoothly.

Konnessjoni elettrika

Connect the ice maker to a standard 120 Volt electrical outlet. Ensure the outlet is properly grounded and meets local electrical codes.

Istruzzjonijiet Operattivi

Panel tal-Kontroll

The ice maker features an intuitive control panel for easy operation. Indicators typically include:

• GĦAMLA SILĠ: Indicates when the unit is actively producing ice.
• SILĠ MILLI: Jixgħel meta l-kontenitur tal-ħażna tas-silġ ikun mimli.
• WASH MODE: Jattiva ċ-ċiklu tat-tindif awtomatiku.

Figure 3: Control panel with Ice, Off, and Wash mode selections.

Produzzjoni tas-Silġ

The Avallon AIMG151GSSILH can produce up to 56 lbs. of ice per day and store up to 26 lbs. The unit will automatically stop ice production when the storage bin is full and resume when ice levels decrease.

Figure 4: Ice production and collection inside the unit.

Figure 5: Ice storage bin filled with gourmet ice.

Silġ Gourmet

This ice maker produces uniquely shaped, clear gourmet ice cubes that melt slowly, preserving the flavor of your beverages.

Figure 6: Close-up of the gourmet ice cubes produced by the unit.

Manutenzjoni

Modalità Aħsel

The ice maker is equipped with a wash mode for easy maintenance. Simply activate this mode via the control panel to initiate a self-cleaning cycle. Refer to the control panel section for details on activating the wash mode.

Tindif Ġenerali

Regular cleaning of your ice maker is essential to ensure optimal performance and hygiene. Follow these general guidelines:

• Periodically clean the interior of the ice storage bin with a mild detergent and warm water. Rinse thoroughly.
• Clean the exterior surfaces with a soft cloth and mild soap. Avoid abrasive cleaners.
• Ensure the air vents are clear of dust and debris to maintain proper airflow and cooling efficiency.

Issolvi l-problemi

If you experience issues with your ice maker, consider the following common solutions:

• L-ebda Produzzjoni tas-Silġ: Check if the unit is powered on, the water supply is connected and turned on, and the ice bin is not full.
• Slow Ice Production: Ensure the unit has adequate ventilation and the ambient temperature is within the recommended operating range.
• Tnixxija tal-Ilma: Verify that all water connections, including the inlet pipe and drain hose, are securely attached and properly positioned for gravity drainage.

For persistent issues, please refer to the detailed troubleshooting section in the full product manual or contact customer support.

Speċifikazzjonijiet

Garanzija u Appoġġ

This product is returnable until January 31, 2026. For any questions or assistance, please contact customer support. Details regarding specific warranty coverage can be found in your purchase documentation or by contacting Avallon customer service directly.