1. Introduzzjoni
This manual provides essential instructions for the safe operation, assembly, maintenance, and troubleshooting of your Total Table Saw 1500W 10-inch, model TS5152542. Please read this manual thoroughly before operating the saw to ensure proper use and to prevent injury or damage.
The Total Table Saw is a corded electric power tool designed for cutting wood and wood-based materials. It features a 1500W motor, a 254mm (10-inch) blade, and operates on 220-240V~50/60Hz power supply.
2. Istruzzjonijiet Ġenerali dwar is-Sigurtà
TWISSIJA: Aqra t-twissijiet, l-istruzzjonijiet, l-illustrazzjonijiet u l-ispeċifikazzjonijiet kollha dwar is-sigurtà pprovduti ma’ din l-għodda tal-enerġija. In-nuqqas li ssegwi l-istruzzjonijiet kollha elenkati hawn taħt jista’ jirriżulta f’xokk elettriku, nar, u/jew korriment serju. Issejvja t-twissijiet u l-istruzzjonijiet kollha għal referenza futura.
Sigurtà taż-Żona tax-Xogħol
- Żomm iż-żona tax-xogħol nadifa u mdawwal sew. Żoni imbarazz jew mudlama jistiednu inċidenti.
- Tħaddimx għodod elettriċi f'atmosferi splussivi, bħal fil-preżenza ta' likwidi, gassijiet jew trab li jaqbdu. Għodod tal-enerġija joħolqu xrar li jistgħu jaqbdu t-trab jew dħaħen.
- Żomm lit-tfal u lil dawk li jkunu fil-qrib 'il bogħod waqt li tħaddem għodda tal-enerġija. Distrazzjonijiet jistgħu jikkawżaw inti titlef il-kontroll.
Sigurtà Elettrika
- Il-plaggs tal-għodda tal-enerġija għandhom jaqblu mal-iżbokk. Qatt mmodifika l-plagg bl-ebda mod.
- Evita l-kuntatt tal-ġisem ma 'uċuħ ertjati jew ertjati, bħal pajpijiet, radjaturi, firxiet, u refriġeraturi. Hemm riskju akbar ta 'xokk elettriku jekk ġismek ikun ertjat jew ertjat.
- Tesponix l-għodod elettriċi għax-xita jew kundizzjonijiet imxarrba. L-ilma li jidħol f'għodda tal-enerġija jżid ir-riskju ta 'xokk elettriku.
- Tabbużax mill-korda. Qatt tuża l-korda biex iġorr, tiġbed jew tneħħi l-plagg tal-għodda tal-enerġija. Żomm il-korda 'l bogħod mis-sħana, żejt, truf li jaqtgħu, jew partijiet li jiċċaqilqu. Kurduni bil-ħsara jew imħabblin iżidu r-riskju ta 'xokk elettriku.
Sigurtà Personali
- Dejjem ilbes protezzjoni għall-għajnejn. Uża tagħmir protettiv personali xieraq bħal maskra tat-trab, żraben tas-sigurtà li ma jiżolqux, elmu iebes, jew protezzjoni għas-smigħ għal kundizzjonijiet xierqa.
- Tlaħħaqx iżżejjed. Żomm sieq tajba u bilanċ f'kull ħin. Dan jippermetti kontroll aħjar tal-għodda tal-enerġija f'sitwazzjonijiet mhux mistennija.
- Ilbes sew. Ilbes ħwejjeġ maħlula jew dehbijiet. Żomm ix-xagħar u l-ilbies tiegħek 'il bogħod minn partijiet li jiċċaqilqu. Ħwejjeġ maħlula, dehbijiet, jew xagħar twil jistgħu jinqabdu f'partijiet li jiċċaqilqu.
- Oqgħod attent, oqgħod attent x'qed tagħmel, u uża s-sens komun meta tħaddem għodda tal-enerġija. Tużax għodda tal-enerġija waqt li tkun għajjien jew taħt l-influwenza tad-drogi, l-alkoħol, jew medikazzjoni.
3. Prodott Aktarview u Komponenti
The Total Table Saw TS5152542 is designed for precision cutting tasks. Familiarize yourself with its main components before operation.
Figura 1: Imla view of the Total Table Saw TS5152542, showing the main table, blade guard, motor housing, and stand with wheels.
Figura 2: Close-up view of the table saw's right-side extension table, which can be adjusted to accommodate wider workpieces.
Figura 3: Detail of the rip fence and its clamping mechanism, used to guide material parallel to the saw blade for accurate cuts.
Komponenti Ewlenin:
- Xafra tas-Serra: Il-komponent tat-tqattigħ, b'dijametru ta' 254mm.
- Tabella: The main work surface (725x490mm).
- Tabelli ta' Estensjoni: Left, right, and rear extensions for larger workpieces.
- Rip Fence: Adjustable guide for parallel cuts.
- Mitra Gauge: For angled cross-cuts.
- Gwardja tax-xafra: Safety cover over the blade.
- Swiċċ mixgħul/mitfi: Kontroll tal-qawwa.
- Blade Height Adjustment Wheel: Controls cutting depth.
- Blade Bevel Adjustment Handle: Controls blade angle for miter cuts.
4. Setup u Assemblea
The table saw requires some assembly before first use. Ensure all components are present and undamaged before proceeding.
Spakkjar u Spezzjoni
- Neħħi b'attenzjoni l-kontenut kollu mill-ippakkjar.
- Inspect the saw for any shipping damage. Do not operate if damaged.
- Iċċekkja li l-partijiet kollha elenkati fil-lista tal-ippakkjar huma preżenti.
Stand Assemblea
Assemble the stand according to the diagrams provided in the separate assembly sheet (if applicable). Ensure all bolts are securely tightened for stability.
Table and Extension Setup
- Attach the extension tables (left, right, and rear) to the main table using the provided hardware.
- Ensure the extension tables are level with the main table surface.
Installazzjoni tax-Xafra (jekk mhux installata minn qabel)
- Skonnettja s-serrieq mill-provvista tal-enerġija.
- Neħħi l-pjanċa tal-gerżuma.
- Using the appropriate wrenches, loosen the arbor nut and install the 254mm blade, ensuring the teeth are facing the correct direction for cutting.
- Issikka l-ġewż tal-arbor sew.
- Reinstall the throat plate and blade guard assembly.
5. Istruzzjonijiet Operattivi
Always wear appropriate safety gear, including eye protection, hearing protection, and a dust mask, before operating the table saw.
Konnessjoni tal-Enerġija
- Connect the power cord to a grounded 220-240V~50/60Hz electrical outlet.
- Ensure the power switch is in the "OFF" position before plugging in.
Aġġustament tal-Għoli u l-Angolu tax-Xafra
- Għoli tax-xafra: Use the blade height adjustment wheel to raise or lower the blade. For most cuts, the blade should extend approximately 3-6mm above the workpiece.
- Blade Angle (Bevel): Loosen the blade bevel adjustment handle and tilt the blade to the desired angle (0-45 degrees). Tighten the handle securely after adjustment.
L-użu tal-Ilqugħ tar-Rip
- Position the rip fence to the desired width of cut, using the scale on the table.
- Securely lock the rip fence in place using its clamping mechanism. Ensure it is parallel to the blade.
Nagħmlu Qatgħa
- Place the workpiece firmly against the rip fence and flat on the table.
- Ixgħel is-serrieq u ħalli x-xafra tilħaq il-veloċità sħiħa.
- Slowly and steadily feed the workpiece into the blade, maintaining firm contact with the fence and table. Use a push stick for narrow cuts.
- Once the cut is complete, turn off the saw and wait for the blade to stop completely before removing the workpiece or off-cuts.
6. Manutenzjoni
Regular maintenance ensures the longevity and safe operation of your table saw. Always disconnect the power supply before performing any maintenance.
Tindif
- After each use, clear sawdust and debris from the table, blade guard, and motor housing using a brush or vacuum cleaner.
- Tużax solventi jew tindif li joborxu.
Kura u Sostituzzjoni tax-Xafra
- Keep the saw blade clean and sharp. A dull blade can cause kickback and poor cut quality.
- Replace worn or damaged blades immediately. Refer to the "Blade Installation" section for replacement procedure. Use only 254mm diameter blades with a 16mm arbor hole.
Ħażna
- Store the table saw in a dry, secure location, out of reach of children.
- Protect the blade from rust by applying a light coat of machine oil if storing for extended periods.
7 Issolvi l-problemi
Din it-taqsima tindirizza kwistjonijiet komuni li tista' tiltaqa' magħhom bis-serrieq tal-mejda tiegħek.
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| Saw ma jibda | Ebda provvista tal-enerġija; Swiċċ difettuż; Tagħbija żejda tal-mutur. | Check power connection and circuit breaker; Inspect switch; Allow motor to cool. |
| Ix-xafra torbot jew tpejjep | Dull blade; Incorrect blade type; Misaligned fence; Forcing workpiece. | Replace or sharpen blade; Use appropriate blade for material; Adjust fence parallel to blade; Reduce feed rate. |
| Qatgħat mhux preċiżi | Fence not parallel; Miter gauge not set correctly; Loose blade. | Adjust fence; Calibrate miter gauge; Tighten blade arbor nut. |
8. Speċifikazzjonijiet
| Karatteristika | Speċifikazzjoni |
|---|---|
| Numru tal-Mudell | TS5152542 |
| Brand | TOTAL |
| Sors tal-Enerġija | Corded Elettriku |
| Voltage | 220-240V ~ 50/60Hz |
| Qawwa tad-Dħul | 1500W |
| Veloċità mingħajr tagħbija | 4500/min (RPM) |
| Dijametru tax-xafra | 254mm x 16mm (10 inch) |
| Max Qtugħ Kapaċità | 80mm |
| Daqs tal-Tabella | 725mm x 490mm |
| Left/Right Extension Table Size | 440mm x 125mm |
| Rear Extension Table Size | 460mm x 125mm |
| Piż tal-oġġett | 45 Kilogrammi |
| Dimensjonijiet tal-Prodott (L x W x H) | 5 x 5 x 5 cm (Note: This dimension seems to be a placeholder or incorrect based on item weight and table size, refer to actual product for accurate dimensions) |
9. Garanzija u Appoġġ
This Total Table Saw TS5152542 is covered by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or contact your retailer.
For technical support, spare parts, or service inquiries, please contact your authorized Total Tools service center or retailer. Keep your purchase receipt and model number (TS5152542) available when seeking support.
Extended warranty options may be available from third-party providers, such as the 1-Year or 2-Year Extended Warranty by Salama Care mentioned in product listings. These are separate from the manufacturer's standard warranty.
