1. Prodott Aktarview
The eSUN eBOX Lite is an upgraded filament dryer box designed to maintain optimal conditions for 3D printing filaments. It effectively removes moisture, preventing common printing issues such as stringing, clogging, and poor adhesion. This device also functions as a filament storage box and spool holder, providing a comprehensive solution for filament management.
Key features include efficient heating, even temperature distribution, low-noise operation, and broad compatibility with various filament types and spool sizes.
Figure 1: eSUN eBOX Lite Filament Dryer Box with a red filament spool inside.
2. Kontenut tal-Pakkett
Ivverifika li l-oġġetti kollha huma preżenti fil-pakkett:
- eBOX Lite Dryer Box
- Adapter tal-Enerġija (Plagg tal-Istati Uniti)
- User Manual (this document, and a physical copy)
- Filament Outlet Tube/Bayonet
Figure 2: Illustration of the eBOX Lite and its included accessories.
3. Istruzzjonijiet ta' Setup
- Pjazzament: Place the eBOX Lite on a stable, flat surface away from direct sunlight, heat sources, and excessive humidity. Ensure adequate ventilation around the unit.
- Konnessjoni tal-Enerġija: Connect the provided power adapter to the DC input port on the back of the eBOX Lite. Plug the adapter into a standard US power outlet (AC100-240V ~ 50/60Hz).
- Tagħbija tal-Filament:
- Open the transparent lid of the eBOX Lite.
- Place your filament spool onto the internal rollers. Ensure the spool rotates freely. The maximum compatible spool size is Φ200mm (diameter) x 73mm (height).
- Thread the filament through the designated outlet hole on the lid. If using the outlet conduit, attach it to the hole and thread the filament through it.
- Agħlaq l-għatu sew.
Figure 3: Visual guide for connecting power and loading filament.
4. Istruzzjonijiet Operattivi
The eBOX Lite features a simple control panel with a display and buttons for setting temperature and time.
4.1. Control Panel Overview
- Wiri: Shows current settings (temperature level, time remaining).
- Buttuna tal-Modalità: Used to cycle between temperature setting mode and time setting mode.
- Buttuni 'l fuq /' l isfel: Used to adjust values (temperature level, time).
4.2. Issettjar tat-Temperatura u l-Ħin
- Qawwa Mixgħul: After connecting the power, the display will light up.
- Set Temperature Level:
- Agħfas il- Modalità button once to enter temperature setting mode. The display will show a number (1, 2, or 3).
- Uża l- 'l fuq/' l isfel buttons to select the desired temperature level based on your filament type:
- Livell 1: Approximately 40°C (suitable for PLA/PLA+)
- Livell 2: Approximately 50°C (suitable for ABS/ABS+/PETG)
- Livell 3: Approximately 55°C (suitable for PVA/Nylon/PC)
- Agħfas il- Modalità button again to confirm the temperature level and proceed to time setting.
- Set Heating Time:
- The display will now show the time setting (e.g., "00.0h").
- Uża l- 'l fuq/' l isfel buttons to set the desired heating duration from 0 to 18 hours. For optimal drying, eSUN recommends at least 2 hours for most filaments.
- Agħfas il- Modalità button again to start the drying process. The display will show the remaining time.
The eBOX Lite will maintain the set temperature and humidity throughout the drying cycle. Once the time expires, the heating will stop, but the box will continue to provide a dry storage environment.
Figure 4: Recommended temperature levels and corresponding filament types.
Figure 5: Graph illustrating humidity reduction over time during drying.
5. Manutenzjoni
Regular maintenance ensures the longevity and optimal performance of your eBOX Lite.
- Tindif: Wipe the exterior of the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure the unit is unplugged before cleaning.
- Tindif Intern: Periodically check the inside of the box for any dust or filament debris. Use a soft brush or compressed air to remove any accumulation.
- Ħażna: Meta ma tkunx qed tintuża għal perjodi estiżi, aqla 'l-apparat u aħżen f'post frisk u niexef.
6 Issolvi l-problemi
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| L-apparat ma jixgħelx. | L-adapter tal-enerġija mhux imqabbad jew difettuż; problema bis-sokit tal-enerġija. | Ensure power adapter is securely connected. Try a different power outlet. Check if the power adapter is damaged. |
| Il-filament mhux qed jinxef sew. | Incorrect temperature level set; insufficient drying time; lid not closed properly. | Verify the correct temperature level for your filament type. Increase drying time (e.g., to 4-6 hours or more for very wet filament). Ensure the lid is fully closed. |
| Id-displej huwa vojt jew ma jirrispondix. | Temporary software glitch; power interruption. | Unplug the device, wait 30 seconds, then plug it back in. If the issue persists, contact customer support. |
| Filament spool does not rotate smoothly. | Spool too large or not seated correctly; debris on rollers. | Ensure spool dimensions are within specifications (Φ200mm x 73mm). Re-seat the spool. Clean the rollers. |
7. Speċifikazzjonijiet
| Parametru | Valur |
|---|---|
| Numru tal-Mudell | eBox-Lite-US |
| Firxa ta 'Temperatura Ġewwa | 40°C - 55°C |
| Hot Plate Temperature | 105°C - 118°C |
| Qawwa Rated | AC100-240V ~ 50/60Hz |
| Output ta 'Qawwa | DC24V ~ 2A |
| Qawwa tal-Heater | 35W |
| Piż tal-Prodott | 0.75 kg (1.65 libbra) |
| Daqs tal-Prodott | 215 x 104 x 238.5 mm |
| Dimensjonijiet tal-Pakkett | 10.91 x 10 x 5.51 pulzieri |
| Max Spool Capacity | Φ200mm (diameter) x 73mm (height) |
| Compatible Filament Diameter | 1.75mm / 2.85mm / 3.00mm |
| Tip ta' Materjal | Polikarbonat |
Figure 6: Detailed product specifications and package contents.
8. Garanzija u Appoġġ
For warranty information and technical support, please refer to the official eSUN webis-sit jew ikkuntattja lis-servizz tal-konsumatur tagħhom direttament. Żomm l-irċevuta tax-xiri tiegħek bħala prova tax-xiri.
You can also find additional resources and a PDF version of the user manual at: eSUN eBOX Lite User Manual (PDF)
