1. Introduzzjoni
This manual provides essential instructions for the safe operation, maintenance, and troubleshooting of your Total Tools Super Select Impact Drill 680W, model TG1061356. Please read this manual thoroughly before using the tool to ensure proper function and to prevent injury.
Informazzjoni Importanti dwar is-Sigurtà: Always wear appropriate personal protective equipment (PPE) such as safety glasses, hearing protection, and gloves when operating power tools. Ensure the work area is clean and well-lit. Disconnect the drill from the power source before making any adjustments or changing accessories.
2. Setup
2.1 Disimballaġġ
Carefully remove the drill and all accessories from the packaging. Inspect for any damage that may have occurred during transit. Retain packaging for future storage or transport.
2.2 Twaħħil tal-Manku Awżiljarju
The auxiliary handle provides additional control and stability. To attach:
- Ħoll il-manku awżiljarju clamp billi ddurha kontra l-arloġġ.
- Żerżaq il-manku fuq quddiem tal-korp tat-trapan.
- Aġġusta l-manku għal pożizzjoni komda għall-qabda tiegħek.
- Issikka l-clamp billi ddurha lejn l-arloġġ sakemm tkun sikura.
Figure 1: Total Tools Super Select Impact Drill with auxiliary handle. The handle is positioned at the front of the drill for improved control.
2.3 Installing a Drill Bit (Keyed Chuck)
This drill features a 13mm keyed chuck for secure bit retention.
- Skonnettja mill-Enerġija: Ensure the drill is unplugged from the power outlet.
- Chuck Miftuħ: Insert the chuck key into one of the holes on the chuck and rotate counter-clockwise to open the chuck jaws.
- Daħħal il-Bit: Place the drill bit into the chuck, ensuring it is centered and inserted as far as possible without touching the chuck jaws' base.
- Issikka ċ-Chuck: Rotate the chuck key clockwise to tighten the chuck jaws firmly around the drill bit. Use all three holes on the chuck to ensure even and secure tightening.
- Neħħi ċ-Ċavetta: Always remove the chuck key before operating the drill.
2.4 Konnessjoni tal-Enerġija
Connect the drill's power cord to a suitable 220V AC power outlet. Ensure the outlet is properly grounded and rated for the drill's power requirements (680W).
3. Istruzzjonijiet Operattivi
3.1 Tixgħel/Jitfi
- Biex Tixgħel: Agħfas is-swiċċ tal-grillu. Il-veloċità tat-trapan hija varjabbli skont kemm ikun ippressat il-grillu.
- To Lock On (for continuous operation): Press the trigger switch fully, then press the lock-on button (usually located on the side of the handle).
- To Turn Off (from locked-on position): Press the trigger switch fully again, then release it.
- To Turn Off (from momentary operation): Simply release the trigger switch.
3.2 Aġġustament tal-veloċità
The drill features variable speed control via the trigger switch. For precise control, a speed pre-selection dial may be present (refer to specific model features if available, otherwise rely on trigger control). Maximum speed is 3000 RPM.
3.3 Mode Selection (Drill / Impact)
This impact drill offers two modes: rotary drilling and impact drilling. A selector switch, typically located on the top or side of the drill, allows you to choose the appropriate mode.
- Rotary Drilling Mode (Drill Symbol): For drilling into wood, metal, plastics, and for screwdriving.
- Impact Drilling Mode (Hammer Symbol): Għat-tħaffir fil-ġebel, il-konkrit, u l-briks.
Figura 2: Ġenb view of the drill, highlighting the mode selector switch (typically near the chuck) and the product label with specifications.
3.4 Funzjoni ta' Reversa
The drill is equipped with a reverse rotation function, useful for removing jammed drill bits or for screwdriving applications. The forward/reverse switch is usually located above the trigger.
- Push the switch to the left for forward rotation (drilling).
- Push the switch to the right for reverse rotation (removing bits).
Dejjem kun żgur li t-trapan waqaf kompletament qabel ma tbiddel id-direzzjoni tar-rotazzjoni.
3.5 Tekniki tat-Tħaffir
- Ġenerali: Applika pressjoni kostanti u uniformi. Tisforzax it-trapan. Ħalli l-bit tat-trapan jagħmel ix-xogħol.
- Injam: Use high speeds and wood-specific drill bits.
- Metall: Use lower speeds and metal-specific drill bits. Apply cutting oil for harder metals to prolong bit life.
- Masonry/Concrete (Impact Mode): Use impact-rated masonry bits. Apply firm, consistent pressure. The impact action will assist in breaking through hard materials.
4. Manutenzjoni
Manutenzjoni regolari tiżgura l-lonġevità u t-tħaddim sikur tat-trapan tiegħek.
4.1 Tindif
- Skonnettja l-Enerġija: Dejjem aqla’ t-trapan qabel ma tnaddaf.
- Barra: Wipe the exterior of the drill with a clean, damp drapp. Tużax kimiċi ħarxa jew tindif li joborxu.
- Slots tal-ventilazzjoni: Żomm il-fetħiet tal-ventilazzjoni ħielsa mit-trab u l-fdalijiet biex tevita li jisħnu żżejjed. Uża arja kkompressata jekk meħtieġ.
4.2 Manutenzjoni taċ-Ċokk
Periodically clean the chuck jaws to ensure proper gripping of drill bits. A small amount of light machine oil can be applied to the chuck jaws to keep them moving smoothly.
4.3 Carbon Brush Inspection (If Applicable)
Some power tools use carbon brushes that wear over time. If your drill experiences reduced power or intermittent operation, the carbon brushes may need inspection or replacement. This procedure should ideally be performed by a qualified service technician.
4.4 Ħażna
Store the drill in a dry, secure location, out of reach of children. Protect it from direct sunlight and extreme temperatures.
5 Issolvi l-problemi
Before attempting any repairs, ensure the drill is unplugged from the power source.
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| It-trapan ma jibdax. | No power supply; faulty power cord/plug; trigger switch issue. | Check power outlet; inspect cord for damage; contact service if switch is faulty. |
| Qawwa mnaqqsa jew tħaddim intermittenti. | Worn carbon brushes; motor overheating; loose connections. | Inspect/replace carbon brushes (if applicable); allow drill to cool; check connections. |
| Drill bit jams frequently. | Bit mhux korrett għall-materjal; pressjoni eċċessiva; bit mhux matt. | Use correct, sharp bit; reduce pressure; clear debris from hole. |
| Vibrazzjoni jew storbju eċċessiv. | Loose chuck; bent drill bit; internal component issue. | Ensure chuck is tight; replace bent bit; contact service for internal issues. |
If the problem persists after attempting these solutions, contact an authorized service center.
6. Speċifikazzjonijiet
The following are the technical specifications for the Total Tools Super Select Impact Drill 680W (Model: TG1061356):
| Karatteristika | Dettall |
|---|---|
| Brand | Għodda Totali |
| Numru tal-Mudell | TG1061356 |
| Sors tal-Enerġija | Corded Elettriku |
| Qawwa Massima | 680 Watts |
| Voltage | 220 Volts |
| Tip Chuck | Ċavetta |
| Daqs Massimu ta' Chuck | 13 Millimetru |
| Veloċità | 3000 RPM (Bla tagħbija) |
| Veloċità Aġġustabbli | Yes (Variable via trigger) |
| Funzjoni Reverse | Iva |
| Hammer Functionality | Yes (Impact Drill) |
| Piż tal-oġġett | 209 g (0.21 Kilogrammi) |
| Dimensjonijiet tal-Prodott | 10 x 20 x 37 ċm |
Figure 3: Approximate dimensions of the Total Tools Impact Drill.
7. Garanzija u Appoġġ
Total Tools products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Total Tools website. For technical support, service, or spare parts, please contact your local Total Tools authorized dealer or service center.
Jekk jogħġbok żomm il-prova tax-xiri tiegħek għal pretensjonijiet ta' garanzija.
