Prodott Overview
The CLEAR CL-BC100W is a wireless backup camera system designed for seamless integration with specific car navigation systems, including the Kenwood MDV-D204. This system eliminates the need for complex wiring from the navigation unit to the camera, simplifying installation. It features a high-quality CCD lens for clear rear view imaging, enhancing safety and convenience during reversing maneuvers.
Quddiem view of the CLEAR CL-BC100W wireless backup camera, showing the lens and mounting bracket.
Prekawzjonijiet ta' Sigurtà Importanti
Before installation and operation, please read the following safety instructions carefully to prevent accidents or damage to the product and vehicle.
- Installation must be performed by a qualified dealer or specialist to ensure safety and proper function.
- Using parts other than those specified or incorrect installation may lead to malfunction or damage. The manufacturer is not responsible for any issues arising from such actions.
- This unit is designed for DC12V vehicles only. Do not use with DC24V vehicles, as it may cause fire or malfunction.
- Before starting any work, always disconnect the vehicle's battery terminal. Failure to do so may result in short circuits or electric shock.
- Ensure all cables are routed securely and do not interfere with the steering wheel, brake pedal, or accelerator pedal during driving, as this can cause serious accidents.
- After installation, confirm proper operation of all electrical components in the vehicle. Improper operation may lead to fire, electric shock, or traffic accidents.
- After installation, confirm the camera's operation. If operation cannot be confirmed due to environmental conditions, perform the operation check in a suitable environment.
- When installing, if the power cable for the backup camera is thin, it is recommended to use solder or crimp terminals for secure connection.
Kontenut tal-Pakkett
Jekk jogħġbok ivverifika li l-komponenti kollha li ġejjin huma inklużi fil-pakkett tiegħek:
- Camera Main Unit
- Cable tal-Enerġija (1m)
- Wireless Kit (Transmitter and Receiver)
- Viti li jiffissaw
- Camera Connection Adapter (may be included depending on the set)
Fuqview of the CLEAR CL-BC100W wireless backup camera components, including the camera, wireless units, and accessories.
Gwida għall-Installazzjoni
Follow these steps for proper installation of your CLEAR CL-BC100W wireless backup camera. Refer to the diagrams for visual guidance.
- Step 1: Prepare for Camera Installation
- Confirm the desired mounting location for the camera and mark the screw positions.
- Clean the mounting surface thoroughly with a suitable cleaner to remove any oil, wax, or dirt.
- Mount the backup camera using the provided screws and adjust its angle for optimal viewing.
- Step 2: Connect Wireless Transmitter Power
- Qabbad il- wajer aħmar of the wireless transmitter's power cord to the vehicle's 12V power supply that activates when the vehicle is in reverse (e.g., the backup lamp power line).
- Qabbad il- wajer iswed (ground) of the wireless transmitter's power cord to the vehicle's chassis.
- Qabbad il- yellow video cable from the wireless transmitter to the camera's video output cable.
- Guideline Display: If the camera cable has a wajer aħdar, cut it to disable the parking guidelines. If it does not have a green wire, guidelines are not displayed.
- Orjentazzjoni tal-Immaġni: If the camera cable has a wajer abjad, cut it to switch the image orientation (e.g., for front view or specific backup applications). If it does not have a white wire, the image is set for standard backup use.
- Nota: The wireless transmitter must be installed inside the vehicle. Installation outside the vehicle may cause malfunction due to exposure to elements.
- Step 3: Connect Wireless Receiver Video
- Qabbad il- yellow video cable from the wireless receiver to the car navigation system's backup camera input terminal.
- Step 4: Connect Wireless Receiver Power
- Qabbad il- wajer aħmar of the wireless receiver's power cord to the vehicle's 12V power supply that activates when the vehicle is in reverse (e.g., the backup lamp power line).
- Qabbad il- wajer iswed (ground) of the wireless receiver's power cord to the vehicle's chassis.
- Step 5: Connect Camera Connection Adapter (if applicable)
- If an adapter is provided, connect it to the dedicated connector on the back of your car navigation system. Then, connect the yellow video cable from the wireless receiver to this adapter.
- The connection method may vary depending on the manufacturer and model of your car navigation system. Refer to your car navigation system's instruction manual for details on its rear connectors.
- If an adapter is not included, connect the RCA cable from the wireless receiver directly to the designated backup camera input on the car navigation system.
- Step 6: Final Operation Check
- After completing all connections, always perform an operation check by engaging reverse gear to ensure the camera displays correctly on your car navigation screen.
- If the camera does not display or displays incorrectly, refer to the Issolvi l-problemi sezzjoni.
Dijagramma tal-Wiring
Detailed wiring diagram illustrating the connections for the CLEAR CL-BC100W wireless backup camera system to the vehicle's power and car navigation unit. The top diagram shows a direct connection, while the bottom diagram shows connection via an adapter.
Suġġerimenti għall-installazzjoni
Cable Management Tip: When routing cables, ensure they are neatly tucked away and secured. For cables passing through the back door, carefully pull the exterior of the harness cover and pins to prevent damage.
Backup Camera Mounting Tip: Install the backup camera in a location where it does not obscure the license plate number or any other legally required markings on your vehicle.
Speċifikazzjonijiet tal-Prodott
| Sensor | Wide-angle 170° High-quality CCD Lens (420,000 pixels) |
| Aġġustament ta' l-Angolu | 120° aġġustabbli |
| Linja gwida | Mixgħul / Mitfi |
| Karatteristiċi oħra | Waterproof/Dustproof compatible |
| Daqs tal-Unità Prinċipali | Width 30mm × Height 24mm × Depth 34mm |
| Piż | Appross. 54g |
| Input tal-Enerġija | DC12V |
| Teknoloġija tas-Sensor Ottiku | CCD |
| Actual Angle of View | 170 grad |
Compatible Car Navigation Systems
This wireless backup camera is designed for specific car navigation systems. Please refer to the lists below to confirm compatibility with your unit. If your model is not listed, compatibility is not guaranteed.
Panasonic Compatibility List
Table detailing compatible Panasonic car navigation models, organized by year.
- Note 1: The backup camera connection is directly to the tuner unit.
- Note 2: If connecting to a second tuner, a separate AV expansion box may be required.
- Note 3: If connecting to a second tuner, the connection may not be removable.
- Note 4: Compatibility for models not explicitly listed in this table is not guaranteed by our company.
Carrozzeria Compatibility List
Table detailing compatible Carrozzeria car navigation models, organized by year.
- Note 1: A camera conversion cable included with the car navigation system is required for connection.
- Note 2: For models manufactured before 2007, connection to the hideaway unit is required.
- Note 3: Compatibility for models not explicitly listed in this table is not guaranteed by our company.
Mitsubishi Compatibility List
Table detailing compatible Mitsubishi car navigation models, organized by year.
- Note: Compatibility for models not explicitly listed in this table is not guaranteed by our company.
Kenwood Compatibility List
Table detailing compatible Kenwood car navigation models, organized by year, including the MDV-D204.
- Note 1: A camera conversion cable included with the car navigation system is required for connection.
- Note 2: If connecting to a second tuner, a separate AV expansion box may be required.
- Note 3: Compatibility for models not explicitly listed in this table is not guaranteed by our company.
Issolvi l-problemi
If you encounter issues with your CLEAR CL-BC100W wireless backup camera, please perform the following checks:
- No Display or Incorrect Display:
- Ensure all power connections (red and black wires) are secure and receiving proper 12V power when the vehicle is in reverse.
- Verify that the video cables (yellow wires) are correctly connected between the camera, wireless units, and the car navigation system.
- Confirm that your car navigation system is set to the correct input source for the backup camera.
- Check the compatibility lists to ensure your car navigation model is supported.
- Image Reversed or Incorrect Guidelines:
- Refer to Step 2 of the Installation Guide regarding the wajer abjad (for image orientation) and wajer aħdar (for guidelines) on the camera cable. Ensure they are cut or left intact as desired.
- Intermittent Signal or Poor Quality:
- Ensure the wireless transmitter is installed inside the vehicle and not obstructed by metal objects.
- Check for any sources of electromagnetic interference near the wireless units.
- If the issue persists after performing these checks, it is recommended to consult a qualified technician.
Appoġġ għall-Klijent
For further assistance, technical support, or inquiries regarding your CLEAR CL-BC100W Wireless Backup Camera, please contact your point of purchase or visit the official CLEAR webgħal aktar informazzjoni.
