Manwal tal-Utent tal-BFT Gate Opener P125002 SB-BAT 24v DC Battery Backup Kit

1. Prodott Aktarview

The BFT SB-BAT (P125002) is a 24v DC battery backup system designed to ensure continuous operation of your gate opener even during power outages. This kit provides a reliable power source, activating automatically when the main power supply is interrupted and recharging when power is restored.

It is compatible with various BFT gate opener models, including the Deimos BT series, VIRGO - LINX, EOS-SCE, HYDRA N, DEIMOS BT-QSC D-NETTUNO S, SB BAT/SB CARBAT (DEIMOS BT-SB 300), BT BAT 2 (URANO BT ARES 1000 & ARES 1500) NETTUNO B, VENERE D, ARGO, LIBRA C MA - LIBRA C LX.

BFT P125002 SB-BAT Battery Backup Kit components

Figure 1: Contents of the BFT P125002 SB-BAT Battery Backup Kit, including batteries, wiring, and mounting hardware.

2. Setup u Installazzjoni

Installation of the BFT SB-BAT kit is designed to be straightforward. It integrates with your existing BFT gate opener system.

2.1. Prekawzjonijiet tas-Sigurtà

Ensure the main power to the gate opener is disconnected before beginning installation.
Ilbes tagħmir protettiv personali (PPE) xieraq.
Refer to your specific gate opener's manual for compatibility and connection points.

2.2. Passi ta 'installazzjoni

Ħoll il-Komponenti: Carefully remove all items from the packaging. Verify all components are present as shown in Figure 1.
Mount the Battery Housing: Securely mount the battery housing unit near your gate opener's control board, ensuring it is protected from environmental elements.
Qabbad il-batteriji: Insert the two 12V 1.2Ah batteries into the housing. Connect them according to the wiring diagram provided with the kit (typically in series to achieve 24V DC).
Connect to Gate Opener: Connect the battery backup system's wiring to the designated battery input terminals on your BFT gate opener's control board. Consult your gate opener's manual for precise terminal locations.
Wiring Sikur: Ensure all wiring is neatly routed and secured to prevent accidental disconnections or damage.
Irrestawra l-Enerġija: Once all connections are secure and verified, restore main power to the gate opener. The smart charger board will begin charging the batteries.

Close-up of BFT P125002 SB-BAT components including batteries and wiring

Figura 2: Egħluq view of the battery backup kit components, highlighting the batteries and connection wires.

3. Operazzjoni

The BFT SB-BAT battery backup system operates automatically to provide uninterrupted gate functionality.

Operazzjoni normali: When main power is available, the smart charger board continuously charges and maintains the batteries.
Qawwa Outage: Fil-każ ta' qawwa outage, the system automatically switches to battery power, allowing the gate opener to continue functioning normally.
Restawr tal-Enerġija: Once main power is restored, the system automatically switches back to main power and resumes charging the batteries.

4. Manutenzjoni

Manutenzjoni regolari tiżgura l-lonġevità u l-affidabbiltà tas-sistema ta' backup tal-batterija tiegħek.

Spezzjoni Viżwali: Periodically inspect the batteries and wiring for any signs of damage, corrosion, or loose connections.
Indafa: Keep the battery housing and terminals clean and free of dust or debris.
Kontroll tas-Saħħa tal-Batterija: While the system has an intelligent charger, it is advisable to periodically test the battery backup by temporarily disconnecting main power to ensure the gate operates on battery power. Reconnect main power after testing.
Sostituzzjoni tal-batterija: Batteries have a finite lifespan. If you notice a significant decrease in backup operation time, it may be time to replace the batteries. Use only recommended replacement batteries (2x 12V 1.2Ah).

5 Issolvi l-problemi

This section addresses common issues you might encounter with your BFT SB-BAT battery backup kit.

Problema	Kawża Possibbli	Soluzzjoni
Il-bieb ma jaħdimx waqt li jkun hemm qtugħ tad-dawltage.	Il-batteriji mhumiex iċċarġjati. Konnessjonijiet tal-wajers maħlula jew mhux korretti. Batteries are at end of life. Fjus minfuħa.	Ensure main power is connected and the charger board is functioning. Allow 12-14 hours for full charge. Check all wiring connections between the battery kit and the gate opener. Test batteries; replace if necessary. Check and replace the 20A fuse if blown.
Batteries do not seem to be charging.	Main power supply issue. Faulty charger board. Konnessjoni ħażina tal-batterija.	Verify main power to the gate opener. Contact BFT support for charger board diagnosis. Recheck battery wiring according to the manual.

6. Speċifikazzjonijiet

Key technical specifications for the BFT SB-BAT (P125002) battery backup system:

Mudell: P125002 SB-BAT
Sistema Voltage: 24V DC
Ħlas Voltage: 27.2V
Iċċarġjar Kurrent: 130mA
Kapaċità tal-batterija: 2x (12V 1.2Ah)
Exhausted Battery Protection Threshold: 20.4V
Ħin tal-Iċċarġjar tal-Batterija: 12-14 sigħat
Fjus: 20A
Manifattur: BFT

7. Garanzija u Appoġġ

For warranty information or technical support, please refer to the documentation included with your purchase or contact BFT customer service directly. Keep your proof of purchase for warranty claims.

You can find more information about BFT products on their official websit jew permezz ta’ distributuri awtorizzati.

	Sistema ta' Awtomazzjoni ta' Bieb Elettromekkanika BFT DEIMOS BT UL/CSA Skopri l-BFT DEIMOS BT UL/CSA, sistema ta' awtomazzjoni elettromekkanika għal xtiebi li jiżżerżqu b'rack. B'teknoloġija intelliġenti, tħaddim sikur ta' 24V, u installazzjoni simplifikata, din is-sistema ttejjeb is-sigurtà u l-konvenjenza tal-bibien. Esplora l-ispeċifikazzjonijiet tekniċi tagħha u l-aċċessorji disponibbli għal applikazzjonijiet residenzjali u kummerċjali.
	Manwal tal-Installazzjoni tal-Awtomazzjoni tal-Bieb Swing BFT VIRGO Gwida komprensiva għall-installazzjoni u l-utent għas-sistema ta' awtomazzjoni tal-bieb swing BFT VIRGO, li tkopri s-sigurtà, l-ispeċifikazzjonijiet tekniċi, il-proċeduri ta' installazzjoni, l-ipprogrammar u l-manutenzjoni.
	Gwida għall-Installazzjoni tas-Sistema ta' Kontroll bir-Radju BFT CLONIX1-2 & MITTO 2-4 433MHz Gwida komprensiva għall-installazzjoni għar-riċevitur BFT CLONIX1-2 u t-trasmettituri tal-kontroll tar-radju MITTO 2-4 433MHz, li tkopri l-ipprogrammar, il-klonazzjoni, is-sigurtà, u l-ispeċifikazzjonijiet tekniċi għall-awtomazzjoni tal-bibien u x-xtiebi.
	Manuale di Installazione BFT THALIA: Quadro Comandi per Automazione Cancelli Din il-gwida tagħtitagliata illustra l'installazione e la configurazione del quadro comandi BFT THALIA, progettato per l'automazione di cancelli e porte. Include specifiche tecniche, schemi di collegamento e istruzioni operative per garantire un funzionamento sicuro ed efficiente.
	Gwida ta' Referenza Rapida tal-BFT Phobos BT Kit UL Gwida ta' referenza rapida għas-sistema ta' ftuħ awtomatiku tal-bibien BFT Phobos BT Kit UL, li tkopri l-installazzjoni, il-wajers, l-ipprogrammar, u s-soluzzjoni tal-problemi.
	Istruzzjonijiet għall-Kodifikazzjoni tar-Remote BFT MITTO 2B \| Remotes Retro Gwida pass pass għall-kodifikazzjoni tar-remotes BFT MITTO 2B għal openers tal-bibien, li tkopri l-metodi eżistenti tal-iskrin LCD tar-remotes u r-riċevituri. Tinkludi pariri dwar is-soluzzjoni tal-problemi.

BFT P125002 SB-BAT