1. Introduzzjoni
The Axxess Integrate AXDIS-CL2 Data Interface is designed to facilitate the installation of an aftermarket radio in select GM vehicles manufactured between 2000 and 2013. This interface provides essential features such as accessory power (12-volt 10-amp), retention of Retained Accessory Power (RAP), OnStar, OEM Bluetooth, and Steering Wheel Control (SWC) functionality. It is compatible with both non-amplified and analog/digital amplified audio systems, ensuring seamless integration with your vehicle's existing electronics.
2. Informazzjoni dwar is-Sigurtà
Please read all instructions carefully before beginning installation. Improper installation can lead to vehicle damage or personal injury. Always disconnect the vehicle's negative battery terminal before installing any electrical components. Ensure all connections are secure and properly insulated to prevent short circuits. If you are unsure about any part of the installation process, consult a qualified automotive electronics technician.
3. Kontenut tal-Pakkett
Ivverifika li l-oġġetti kollha huma preżenti qabel ma tipproċedi bl-installazzjoni:
- AXDIS-CL2 Data Interface Module
- Vehicle-specific wiring harness
- Manwal ta' Istruzzjoni
Image 1: Contents of the AXDIS-CL2 package, showing the main module and various wiring harnesses.
4. Setup u Installazzjoni
The AXDIS-CL2 is compatible with a wide range of GM vehicles from 2000 to 2013, including models from Buick, Cadillac, Chevrolet, GMC, Hummer, Isuzu, Oldsmobile, Pontiac, Saab, and Saturn. This interface is designed to simplify aftermarket radio installation by providing necessary data conversions.
4.1 Konnessjonijiet tal-Wiring
Connect the vehicle-specific harness to the AXDIS-CL2 module. Then, connect the other end of the harness to your aftermarket radio's wiring harness, matching wire functions (e.g., power, ground, speaker outputs, accessory, illumination). Ensure all connections are soldered or crimped securely and insulated with electrical tape or heat shrink tubing.
- Qawwa Aċċessorju: L-interface jipprovdi 12-volt 10-amp accessory output.
- Retained Accessory Power (RAP): The interface retains the RAP feature, allowing the radio to operate for a short period after the ignition is turned off.
- OnStar/OEM Bluetooth: The interface retains the functionality of the factory OnStar and OEM Bluetooth systems.
- Chimes: Factory warning chimes are retained through the interface.
Immaġni 2: Dettaljata view of the AXDIS-CL2 module and various connectors for vehicle integration.
4.2 Steering Wheel Control (SWC) Programming
The AXDIS-CL2 automatically detects the vehicle and the aftermarket radio for most applications. After connecting all wires, turn on the ignition. The interface will typically auto-program the SWC functions. If SWC buttons do not function correctly, refer to the detailed programming instructions provided in the full product manual (not included in this summary) or visit the Axxess website for specific vehicle and radio programming steps.
5. Tħaddim tal-Interfaċċja
Once installed and programmed, the AXDIS-CL2 operates transparently, allowing your aftermarket radio to function as intended while retaining key factory features. The Steering Wheel Controls will operate the corresponding functions on your aftermarket radio (e.g., volume up/down, track skip, mode). OnStar and OEM Bluetooth will continue to function through the vehicle's factory systems.
6. Manutenzjoni
The AXDIS-CL2 Data Interface requires no regular maintenance. Ensure it is installed in a dry, secure location away from excessive heat or moisture. Do not attempt to open the module casing, as this may void the warranty and could damage the device.
7 Issolvi l-problemi
Jekk tiltaqa' ma' problemi wara l-installazzjoni, ikkunsidra dan li ġej:
- L-ebda Enerġija għar-Radju: Check all power and ground connections. Ensure the vehicle's battery is fully charged. Verify the accessory wire from the interface is connected to the radio's accessory input.
- Kontrolli tal-Istering Wheel Mhux Jaħdmu: Confirm the SWC wire from the interface is correctly connected to the aftermarket radio's SWC input. Re-attempt the SWC programming sequence. Some aftermarket radios require specific settings for external SWC interfaces.
- Ebda Ħsejjes: Check all speaker wire connections. Ensure the vehicle's amplifier (if present) is receiving power and a turn-on signal. Verify the radio's fader/balance settings.
- OnStar/Bluetooth Issues: Ensure the interface is correctly connected to the vehicle's data bus. If issues persist, consult the vehicle's factory service manual or an authorized technician.
8. Speċifikazzjonijiet
| Numru tal-Mudell | AXDIS-CL2 |
| Dimensjonijiet tal-Prodott | 7.5 x 4 x 2.5 pulzieri |
| Piż tal-oġġett | 0.33 Kilogrammi (11.68 uqija) |
| Materjal | Alloy Steel, Copper, Plastic, Stainless Steel |
| Tip ta' Konnettur | USB (for firmware updates/programming, if applicable) |
| Manifattur | Metra Electronics |
9. Informazzjoni dwar Garanzija
The Axxess Integrate AXDIS-CL2 Data Interface is covered by a manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty card included with your product or visit the Axxess website for specific terms and conditions, including warranty duration and claim procedures.
10. Appoġġ
For technical assistance or further inquiries regarding the AXDIS-CL2 Data Interface, please contact Axxess customer support. You can find contact information, frequently asked questions, and additional resources on the official Axxess websit.
