1. Introduzzjoni
This manual provides detailed instructions for the safe and effective installation, operation, and maintenance of your Onforu 48W LED RGB Wall Washer Light, Model CTB24RGB. Please read this manual thoroughly before use and retain it for future reference.
Image 1.1: Two Onforu 48W LED RGB Wall Washer Lights with remote controls.
2. Istruzzjonijiet tas-Sigurtà
- Tiżgura l-provvista tal-enerġija voltage jaqbel mar-rekwiżiti tal-prodott (120V).
- Do not disassemble, modify, or repair the product yourself. Contact qualified personnel for service.
- Żomm il-prodott 'il bogħod minn materjali li jaqbdu.
- The power plug is not waterproof. Ensure it is protected from water exposure, especially during outdoor use.
- Evita l-espożizzjoni diretta tal-għajnejn għas-sors tad-dawl.
- Dejjem skonnettja l-enerġija qabel l-installazzjoni, it-tindif, jew il-manutenzjoni.
3. Kontenut tal-Pakkett
Ivverifika li l-komponenti kollha huma preżenti u mhux imħassra malli tiftaħ il-pakkett:
- Onforu 48W LED RGB Wall Washer Light (x2)
- 44-Key RF Remote Control (x2)
- Brazzi tal-Immuntar (x4)
- M5 Hex Screw Key (x1)
- Viti (x4)
- Plastic Expansion Nails (x9)
- Screws for Mounting (x9)
Immaġni 3.1: Id-dimensjonijiet tal-prodott u l-aċċessorji inklużi.
4. Speċifikazzjonijiet
| Karatteristika | Speċifikazzjoni |
|---|---|
| Numru tal-Mudell | CTB24RGB |
| Qawwa | 48 Watts |
| Voltage | 120 Volts |
| Luminożità | 7200 Lumens |
| Tip ta' Sors tad-Dawl | LED |
| Kulur | RGB (Color Changing) |
| Materjal | Aluminju, Ħġieġ ittemprat |
| Tip Finish | Trab Miksija |
| Klassifikazzjoni tal-IP | IP66 (Light Bar) |
| Dimensjonijiet tal-Prodott | 15.74"T x 3.14"W x 2.48"Għ |
| Piż tal-oġġett | 2 Liri |
| Tul tal-Kunda tal-Enerġija | 3.93 pied (1 metri) |
| Firxa ta 'Kontroll mill-bogħod | Sa 26.25 pied (8 metru) |
| Ħajja Medja | 30,000 Sigħat |
5. Installazzjoni
5.1 Immuntar tal-Bar tad-Dawl
- Attach the mounting brackets to the light bar using the provided screws. The brackets allow for 180-degree adjustment.
- Choose a suitable location for installation (ceiling, wall, or ground). Ensure the surface can support the weight of the light.
- Mark the drilling points on the chosen surface using the bracket holes as a guide.
- Drill holes at the marked points. For masonry or concrete, insert the plastic expansion nails.
- Secure the light bar with the attached brackets to the surface using the mounting screws.
- Adjust the angle of the light bar as desired.
5.2 Konnessjoni Elettrika
- Ensure the power outlet is easily accessible and protected from moisture, especially for outdoor installations.
- Ipplaggja l-korda tad-dawl fi żbokk standard ta '120V AC.
- The light bar is IP66 waterproof, but the power plug is not. Protect the plug and connection point from water.
6. Istruzzjonijiet Operattivi
6.1 Remote Control Functions (44-Key RF Remote)
The light bar is controlled by the included 44-key RF remote control. The remote has a sensing distance of up to 26.25 feet (8 meters).
Image 6.1: Remote control operation and timer function.
6.2 Modi tal-Kulur
The light offers 20 basic colors and 6 lighting modes:
- 20 Basic Colors: Select directly from the color buttons on the remote.
- 6 Modi tad-Dawl: Includes Fade, Jump, Flash, and other dynamic effects. Refer to the remote control for specific mode buttons.
Immaġni 6.2: Eż.amples of 20 colors and 6 modes.
6.3 DIY Color Settings
The remote control features three DIY settings (DIY1, DIY2, DIY3) allowing you to customize colors by adjusting the proportion of red, green, and blue. Follow these steps:
- Press one of the DIY buttons (DIY1, DIY2, or DIY3) to enter DIY mode.
- Use the Red, Green, and Blue arrow buttons (up/down) to increase or decrease the intensity of each primary color.
- Once satisfied with your custom color, press the same DIY button again to save it.
- You can recall your saved DIY colors by pressing the corresponding DIY button.
Image 6.3: DIY color setting functionality.
6.4 Funzjoni tal-Ħin
The timing function allows you to set the light to automatically turn off after a specified duration:
- Press the 3H, 6H, or 12H button on the remote to activate the timer for 3, 6, or 12 hours, respectively.
- The light will automatically turn off once the set time has elapsed.
6.5 Funzjoni tal-Memorja
The light bar retains its last used settings (color, mode, and brightness) when powered off and on again. No need to reset your preferred configuration.
7. Manutenzjoni
- Tindif: Skonnettja l-provvista tal-enerġija qabel it-tindif. Uża drapp artab u damp cloth to wipe the surface of the light bar. Do not use abrasive cleaners or solvents.
- Spezzjoni: Periodically check the power cord for any damage. Ensure all mounting screws are tight.
- Ħażna: If storing the light for an extended period, ensure it is clean and dry. Store in a cool, dry place away from direct sunlight.
8 Issolvi l-problemi
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| Id-dawl ma jixgħelx | No power supply; Loose connection; Faulty outlet. | Check power connection; Ensure outlet is functional; Try a different outlet. |
| Il-kontroll mill-bogħod ma jaħdimx | Remote battery depleted; Obstruction between remote and light; Remote too far. | Replace remote battery; Remove obstructions; Operate within 26.25 ft range. |
| Colors or modes not changing | Remote control issue; Light malfunction. | Ensure remote is pointed at the light's sensor; Try resetting the light by unplugging and replugging. If issue persists, contact support. |
| DIY colors not saving | DIY button not pressed again to save. | After adjusting RGB values, press the same DIY button (DIY1, DIY2, or DIY3) again to save the custom color. |
9. Garanzija u Appoġġ
Onforu products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please refer to the contact information provided with your purchase or visit the official Onforu websit. Żomm l-irċevuta tax-xiri tiegħek bħala prova tax-xiri għal talbiet ta' garanzija.
