Introduzzjoni
This manual provides essential information for the safe and efficient operation of your ProCom ML1PHG Ventless Propane Gas Infrared Space Heater. Please read all instructions carefully before installation and use. This heater is designed to provide supplemental heat for indoor residential spaces.
Figure 1: ProCom ML1PHG Ventless Propane Gas Infrared Space Heater, front view.
Informazzjoni dwar is-Sigurtà
Is-sigurtà tiegħek u s-sigurtà ta’ ħaddieħor huma importanti ħafna. Dan il-manwal fih messaġġi importanti dwar is-sigurtà. Dejjem aqra u obdi l-messaġġi kollha dwar is-sigurtà.
- This appliance is for use with Propane Gas only.
- Taħżinx jew tużax gażolina jew fwar u likwidi oħra li jaqbdu fil-viċinanza ta' dan jew kwalunkwe apparat ieħor.
- Installation and repair must be done by a qualified service person. The appliance must be installed in accordance with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.
- This heater is equipped with an Oxygen Depletion Sensor (ODS) pilot system. The ODS will shut off the heater if oxygen levels in the room become too low. Do not tamper with the ODS.
- Kun żgur li jkun hemm ventilazzjoni adegwata meta tħaddem il-ħiter.
- Keep combustible materials, such as furniture, drapes, and clothing, at least 3 feet (0.9 meters) away from the front of the heater.
Kontenut tal-Pakkett
Iċċekkja li l-komponenti kollha huma preżenti qabel tibda l-installazzjoni.
- Vent Free Heater (Qty. 1)
- Wall Mounting Bracket (Qty. 1)
- Hardware Package (Qty. 1)
Setup u Installazzjoni
The ProCom ML1PHG heater can be wall-mounted using the included bracket or placed on a floor with optional base feet (sold separately).
Immuntar tal-ħajt
- Select a suitable wall location, ensuring it is away from combustible materials and has proper clearances.
- Attach the wall mounting bracket securely to the wall using the provided hardware. Ensure the bracket is level and firmly anchored to wall studs or appropriate anchors.
- Carefully lift the heater and align the mounting slots on the back of the heater with the bracket. Lower the heater onto the bracket until it is securely seated.
Figura 2: Eżample of the heater mounted on a wall.
Konnessjoni tal-Gass
This heater operates on Liquid Propane (LP) gas only. A qualified technician must perform the gas connection.
- Ensure the main gas supply valve is off before making any connections.
- Connect the propane supply line to the heater's gas inlet. Use appropriate gas-rated sealant on all threaded connections.
- Check all connections for leaks using a soap solution. Never use an open flame to check for leaks.
Figura 3: Close-up view of the Liquid Propane (LP) gas connection point.
Istruzzjonijiet Operattivi
The ML1PHG heater features a manual control for simple operation.
Proċedura ta' Tqabbid
- Kun żgur li l-valv tal-provvista tal-gass għall-heater ikun miftuħ.
- Locate the control knob on the top of the heater.
- Push the control knob in and turn it counter-clockwise to the PILOT/IGN pożizzjoni.
- While holding the knob in, repeatedly press the INDIKATUR button until the pilot flame ignites. You should see a small blue flame.
- Kompli żomm il-pum tal-kontroll magħfus għal madwar 30-60 sekonda wara li l-pilota jixgħel biex tħalli t-termokoppja tisħon.
- Release the control knob. The pilot flame should remain lit. If it extinguishes, repeat steps 3-5.
- Once the pilot is lit, push the control knob in slightly and turn it counter-clockwise to the desired heat setting: BAXXA or GĦOLJA. The main burner will ignite.
Figure 4: Control knob and ignitor button for operation.
Figure 5: The radiant ceramic plaques will glow red during operation.
Shutting Down the Heater
- To turn off the main burner, turn the control knob clockwise to the OFF position. The pilot flame will also extinguish.
- For extended periods of non-use, turn off the main gas supply valve to the heater.
Manutenzjoni
Manutenzjoni regolari tiżgura l-lonġevità u t-tħaddim sikur tal-ħiter tiegħek.
- Tindif: Keep the heater area clear and free from combustible materials, dust, lint, and pet hair. Use a soft, dry cloth to clean the exterior surfaces. Do not use abrasive cleaners.
- Spezzjoni tal-Pilota u l-Burner: Periodically inspect the pilot and main burner for proper flame appearance. The pilot flame should be steady and blue. The main burner flame should be blue with no yellow tipping.
- Ventilazzjoni: Ensure that air openings on the heater are not obstructed.
- Spezzjoni Annwali: It is recommended to have the heater inspected annually by a qualified service technician.
Issolvi l-problemi
Irreferi għat-tabella li ġejja għal kwistjonijiet komuni u s-soluzzjonijiet tagħhom.
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| Il-pilota mhux se jixgħel | No gas supply; Air in gas line; Pilot orifice clogged; Thermocouple faulty; ODS activated. | Ensure gas supply is on; Bleed air from line; Clean pilot orifice; Replace thermocouple; Check ventilation. |
| Pilot lights but main burner will not ignite | Control knob not held long enough; Low gas pressure; Main burner orifice clogged. | Hold knob for 30-60 seconds; Check gas supply pressure; Clean main burner orifice. |
| Heater produces odor | New heater burn-off; Dust accumulation; Inadequate ventilation. | Operate for a few hours in a well-ventilated area; Clean heater; Increase ventilation. |
| Il-heater jintefa bla mistenni | ODS activation (low oxygen); Pilot flame extinguished; Gas supply interrupted. | Ensure adequate ventilation; Relight pilot; Check gas supply. |
Jekk il-passi għas-soluzzjoni tal-problemi ma jsolvux il-problema, ikkuntattja tekniku tas-servizz kwalifikat.
Speċifikazzjonijiet
| Karatteristika | Dettall |
|---|---|
| Brand | ProCom |
| Numru tal-Mudell | ML1PHG |
| Tip ta' Fjuwil | Gass Propan Biss |
| Maximum BTU Output | 10,000 BTU |
| Kopertura tat-Tisħin | Sa 500 Sq. Ft. |
| Tip ta' Kontroll | Manual (On/Off Settings) |
| Sistema ta 'Tqabbid | Push Button Piezo Ignition |
| Karatteristiċi tas-Sigurtà | Oxygen Depletion Sensor (ODS) with automatic shut-off |
| Elettriku Meħtieġ | Nru |
| Dimensjonijiet tal-Prodott (H x W x D) | 18.5" Għoli x 24" Wisa' x 8" Fond |
| Piż tal-Prodott | 13 lbs. |
| Tip ta 'Immuntar | Immuntar mal-ħajt (ħardwer inkluż) |
| UPC | 848660004002 |
Figure 6: Product dimensions of the ProCom ML1PHG heater.
Informazzjoni dwar Garanzija
This ProCom ML1PHG Ventless Propane Gas Infrared Space Heater comes with a Garanzija Limitata ta' Sena from the date of purchase. This warranty covers defects in materials and workmanship under normal use and service. For full warranty details and to make a claim, please refer to the documentation included with your product or contact ProCom customer support.
Appoġġ għall-Klijent
For technical assistance, parts, or service inquiries, please contact ProCom customer support. Have your model number (ML1PHG) and purchase date available when contacting support.
Note: Contact information for ProCom is not provided in the product data. Please refer to the manufacturer's official website or product packaging for direct support channels.
