Work Sharp Electric Kitchen Knife Sharpener User Manual

1. Introduzzjoni

The Work Sharp Electric Kitchen Knife Sharpener is designed to provide fast, easy, and consistent sharpening for all your kitchen knives, including serrated edges, as well as scissors and shears. This manual provides instructions for setup, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your sharpener.

Figure 1: Work Sharp Electric Kitchen Knife Sharpener and its packaging.

2. Setup

Before first use, ensure the sharpener is placed on a stable, flat surface. The power cord is conveniently stored in the base of the unit.

1. Unwind the power cord from the storage compartment located on the underside of the sharpener.
2. Ipplaggja l-adapter tal-enerġija fi żbokk elettriku standard.
3. Ensure the sharpener is stable and ready for use.

Figure 2: The underside of the sharpener with the power cord neatly stored.

3. Istruzzjonijiet Operattivi

3.1. Tisħin tas-Skieken

The sharpener features angle guides and flexible abrasive discs for precise and gentle sharpening.

1. Press the power button located on the side of the sharpener to turn it on.
2. Rest your knife blade in the appropriate angle guide slot (left or right). The sharpener is designed to automatically set the correct sharpening angle.
3. Draw the knife blade through the slot at a consistent rate, approximately one inch per second. Alternate sides for even sharpening.
4. The sharpener will automatically shut off after a timed sharpening cycle (approximately 90 seconds per side).
5. After the sharpening cycle, use the built-in ceramic hone wheel (located in the center slot) to remove any burrs and refine the edge. Draw the knife through the honing slot a few times, alternating sides.

Figure 3: Sharpening a kitchen knife using the Work Sharp Electric Kitchen Knife Sharpener.

Figure 4: The sharpener provides perfectly sharpened knives every time.

3.2. Sharpening Scissors and Shears

The sharpener can also be used for scissors and shears by removing the knife angle guide.

1. Ensure the sharpener is unplugged.
2. Gently push the knife angle guide from the back to remove it. This will expose the dedicated scissor sharpening guide.
3. Open your scissors and lay one blade flat on the exposed scissor sharpening guide.
4. Plug in the sharpener and press the power button.
5. Draw the scissor blade through the slot at a consistent rate, maintaining contact with the abrasive. Perform two passes on one side, then two passes on the other side.
6. Repeat for the second scissor blade if necessary.

Figure 5: Diagram illustrating the components, including the removable angle guides and the internal scissor sharpening guide.

3.3. Vidjows Uffiċjali tal-Prodott

4. Manutenzjoni

Regular maintenance ensures the longevity and effectiveness of your sharpener.

4.1. Tindif

After each use, it is recommended to clean the sharpener to remove any metal shavings or dust.

1. Unplug the sharpener from the power outlet.
2. Remove the knife angle guide.
3. Open the top housing of the sharpener to access the internal components.
4. Use a dry cloth or a soft brush to gently wipe away any accumulated metal dust or debris from the abrasive discs and the internal compartment.
5. Close the housing and reattach the knife angle guide.

Figure 6: Close-up of the sharpener's slots, where metal shavings may accumulate.

4.2. Replacing Abrasive Discs

The flexible abrasive discs are designed for long life and can be reversed for extended use. Replacement abrasive packs are available from Work Sharp.

1. Ensure the sharpener is unplugged.
2. Remove the knife angle guide and open the top housing.
3. Carefully remove the retaining caps on the abrasive discs.
4. Flip the discs over to use the fresh side, or replace them with new discs from a Work Sharp replacement abrasive pack.
5. Reattach the retaining caps, close the housing, and reattach the knife angle guide.

5 Issolvi l-problemi

If you encounter any issues with your Work Sharp Electric Kitchen Knife Sharpener, please refer to the following common solutions:

• Sharpener does not turn on: Ensure the power cord is securely plugged into both the sharpener and a working electrical outlet. Check if the outlet itself is functional.
• Is-skieken mhumiex qed jissann sew: Ensure you are drawing the knife through the slots at the recommended speed (approx. 1 inch per second) and alternating sides. The abrasive discs may need to be reversed or replaced if they are worn out.
• Storbju eċċessiv waqt it-tħaddim: This could indicate that the abrasive discs are worn or that there is debris inside the sharpener. Perform the cleaning steps outlined in Section 4.1.

For further assistance, please contact Work Sharp customer support.

6. Speċifikazzjonijiet

7. Garanzija u Appoġġ

All Work Sharp sharpeners come with a comprehensive 3-year warranty. Each knife & tool sharpener is meticulously designed and quality-checked at our Oregon facility. We proudly stand behind our products.

For detailed warranty information or customer support, please refer to the official Work Sharp website or the User Manual (PDF) available for download:

Niżżel il-Manwal tal-Utent (PDF)