Manwal tal-Utent tal-Faucet tal-Kċina Pull-Down b'Manku Wieħed tal-Kċina tal-Proġett Sors Chrome

Introduzzjoni

This manual provides detailed instructions for the installation, operation, and maintenance of your Project Source Chrome 1-Handle Pull-Down Kitchen Faucet, model 51-K814-PS-CP. Please read this manual thoroughly before beginning installation and retain it for future reference.

Informazzjoni dwar is-Sigurtà

• Always turn off the main water supply before installing or servicing the faucet.
• Ilbes nuċċalijiet u ingwanti tas-sigurtà waqt l-installazzjoni biex tevita l-korrimenti.
• Kun żgur li l-konnessjonijiet kollha huma sikuri biex tevita t-tnixxijiet.
• Jekk m'intix ċert dwar xi parti tal-proċess tal-installazzjoni, ikkonsulta plamer kwalifikat.

Kontenut tal-Pakkett

Iċċekkja li l-komponenti kollha huma preżenti qabel tibda l-installazzjoni:

Figura 1: All components of the Project Source pull-down kitchen faucet, including the main faucet body, hot and cold water supply lines, mounting hardware, deck plate, and instruction manual.

• Main Faucet Body with Pull-Down Sprayer
• Hot and Cold Water Supply Lines (pre-attached)
• Mounting Hardware (nut, washer, gasket)
• Deck Plate (optional, for 3-hole sinks)
• Weight (for pull-down hose)
• Manwal ta' Istruzzjoni

Setup u Installazzjoni

Għodod Meħtieġa:

• Wrench aġġustabbli
• Tornavit tar-ras Phillips
• Stokk tal-Plumber jew Siġillant tas-Silikon
• Bucket (for catching drips)
• Flashlight

Passi ta' Installazzjoni:

1. Ipprepara l-Sink: Turn off the hot and cold water supply valves under the sink. Open the existing faucet to drain any remaining water. Disconnect and remove the old faucet. Clean the sink surface thoroughly.
2. Installa l-Pjanċa tal-Gverta (Mhux obbligatorja): If your sink has three holes, place the deck plate (if using) over the sink holes. Apply a thin bead of plumber's putty or silicone sealant around the underside edge of the deck plate to create a watertight seal.
3. Immonta l-Faucet: Insert the faucet body through the center hole of the sink (and deck plate, if used). From underneath the sink, slide the rubber washer, then the metal washer, and finally thread the mounting nut onto the faucet shank. Hand-tighten, then use an adjustable wrench to secure it firmly, ensuring the faucet is properly aligned.
4. Qabbad il-Linji tal-Provvista tal-Ilma: Connect the hot and cold water supply lines from the faucet to the corresponding hot and cold water supply valves. The faucet's lines are typically labeled (e.g., "HOT" for hot water). Hand-tighten, then use an adjustable wrench for a final quarter-turn. Do not overtighten.
5. Install Hose Weight: Locate the indicator on the pull-down hose (usually a sticker or mark) where the weight should be installed. Attach the provided weight to the pull-down hose at this indicated position. This weight helps the sprayer retract smoothly.
6. Iċċekkja għal Tnixxijiet: Slowly turn on the hot and cold water supply valves. Check all connections for leaks. If leaks are present, tighten the connections slightly until the leak stops.
7. Laħlaħ il-Vit: Remove the sprayer head and turn on the faucet to flush out any debris from the lines. Let the water run for a few minutes. Turn off the faucet, reattach the sprayer head, and check for proper operation.

Istruzzjonijiet Operattivi

• Fluss u Temperatura tal-Ilma: The single handle controls both water flow and temperature. Lift the handle to increase water flow. Move the handle to the left for hot water and to the right for cold water.
• Sprejer li Jiġbed 'l Isfel: Grasp the sprayer head and pull it down from the spout. The hose will extend to allow for greater reach. Press the button on the sprayer head to switch between stream and spray functions. When finished, guide the sprayer head back into the spout; the hose weight will assist in retraction.

Manutenzjoni

• Tindif: Naddaf il-vit regolarment b'ċarruta ratba u sapun ħafif. Evita prodotti tat-tindif li joborxu, kimiċi ħarxa, jew sponġi tal-għorik, għax dawn jistgħu jagħmlu ħsara lill-finitura tal-kromju.
• Tindif tal-arjatur: If water flow decreases, the aerator may be clogged. Unscrew the aerator from the tip of the sprayer head, clean any debris, and rinse thoroughly before reattaching.
• Hose Weight Adjustment: If the pull-down sprayer does not retract smoothly, check the position of the hose weight. Adjust its position along the hose as needed to ensure proper retraction.

Issolvi l-problemi

Speċifikazzjonijiet

Garanzija u Appoġġ

For warranty information or technical support, please refer to the contact details provided with your purchase documentation or visit the official Project Source websit. Żomm l-irċevuta tax-xiri tiegħek bħala prova tax-xiri għal talbiet ta' garanzija.