1. Introduzzjoni
Thank you for choosing the TOOLCRAFT TC-FC-USB Polystyrene Cutter. This versatile 5W tool is designed for precise cutting and engraving of polystyrene and similar foam materials. Powered conveniently via USB, it offers quick heating and comes with three interchangeable tips for various applications. Please read this manual thoroughly before first use to ensure safe operation and optimal performance.
2. Istruzzjonijiet tas-Sigurtà
- Periklu tas-Sħana: The cutting wire and tips become extremely hot during operation. Avoid direct contact with skin to prevent burns.
- Ventilazzjoni: Use the tool in a well-ventilated area. Cutting polystyrene can release fumes.
- Materjali li jaqbdu: Do not use near flammable liquids, gases, or materials.
- Tfal u Pets: Żomm l-għodda fejn ma jintlaħaqx mit-tfal u l-annimali domestiċi.
- Sors tal-Enerġija: Only connect to a USB power source (e.g., computer, power bank, USB adapter) that provides 5V.
- Aqla' meta ma tkunx qed tuża: Always disconnect the USB cable when the tool is not in use or before changing tips.
- Spezzjona qabel l-użu: Check the cutting wire and tips for damage before each use. Do not use if damaged.
- Immaniġġjar kif suppost: Hold the tool firmly by the handle. Do not apply excessive force, as this can damage the tips or wire.
- Ħażna: Ħalli l-għodda tiksaħ kompletament qabel ma taħżinha.
3. Kontenut tal-Pakkett
Kun żgur li l-oġġetti kollha huma preżenti fil-pakkett tiegħek:
- 1 x TOOLCRAFT TC-FC-USB Polystyrene Cutter main unit
- 1 x Cutting wire tip (bow-shaped)
- 1 x Blade tip (needle-shaped)
- 1 x Engraving tip (pointed)
- 1 x USB power cable (integrated)
4. Prodott Aktarview
The TOOLCRAFT TC-FC-USB Polystyrene Cutter consists of a main handle unit with an integrated USB cable and interchangeable heating tips. The handle features a power switch and an articulation point for comfortable use.
Figura 1: Fuqview of the TOOLCRAFT TC-FC-USB Polystyrene Cutter and its included accessories, including the main unit, cutting wire tip, blade tip, and engraving tip.
5. Setup
- Select the Desired Tip: Choose between the cutting wire, blade tip, or engraving tip based on your task.
- Waħħal il-Parta: Align the chosen tip with the receptacle at the end of the main unit. Gently push and twist until it is securely seated. Ensure a firm connection for proper heating.
- Qabbad l-Enerġija: Plug the integrated USB cable into a compatible 5V USB power source (e.g., a computer USB port, a USB wall adapter, or a power bank).
Figura 2: The main unit with the bow-shaped cutting wire tip securely attached, ready for use.
6. Istruzzjonijiet Operattivi
- Qawwa Mixgħul: Once the tip is attached and the USB cable is connected, slide the power switch on the handle to the 'ON' position. An indicator light may illuminate.
- Ħin tat-tisħin: The tool heats up quickly. The cutting wire reaches approximately 180°C, and other tips reach around 320°C. Allow a few moments for the tip to reach its optimal temperature.
- Cutting/Engraving: Gently guide the heated tip through the polystyrene or foam material. Do not apply excessive pressure; the heat should do the work. For cutting, maintain a steady, even motion. For engraving, use the pointed tip to draw desired patterns.
- Articulated Handle: The handle features a rotating articulation point, allowing you to adjust the angle of the tip for improved ergonomics and access to different cutting positions.
- Itfi: After use, slide the power switch to the 'OFF' position and disconnect the USB cable.
- Kessaħ: Allow the tip to cool completely before handling or storing the tool.
Figura 3: Demonstrates the use of the blade tip for precise cutting of polystyrene foam.
Figura 4: Illustrates the engraving tip being used to create patterns on a foam surface.
7. Manutenzjoni
- Tindif: Ensure the tool is unplugged and completely cool before cleaning. Gently wipe the tips and handle with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- Sostituzzjoni tal-ponta: If a tip becomes damaged or worn, ensure the tool is cool and unplugged. Carefully remove the old tip and replace it with a new, compatible TOOLCRAFT tip.
- Ħażna: Aħżen l-għodda u l-aċċessorji tagħha f'post xott u sigur, 'il bogħod mix-xemx diretta u minn temperaturi estremi.
8 Issolvi l-problemi
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| L-għodda ma tissaħħanx. | Not powered on; USB cable not connected; Faulty USB port; Tip not properly seated. | Ensure power switch is ON. Check USB connection. Try a different USB port or power source. Re-seat the tip firmly. |
| Cutting wire/tip breaks easily. | Excessive force applied; Material too dense; Wire/tip is worn. | Apply less pressure; allow heat to do the work. Ensure material is suitable for cutting. Replace with a new tip. |
| Prestazzjoni fqira tat-tqattigħ. | Insufficient heat; Tip is dirty or damaged. | Allow more time for heating. Clean the tip (when cool). Replace damaged tips. |
9. Speċifikazzjonijiet
- Ditta: GĦODDA
- Numru tal-Mudell: TO-4941084
- Dimensjonijiet tal-Prodott (L x W x H): 14.9 x 3 x 3 ċm
- Piż: 66 Gramm
- Kulur: Iswed
- Sors tal-Enerġija: Powered mill-USB
- Voltage: 5 Volts
- Qawwa: 5 Watts
- Materjal tal-manku: Plastik
- Karatteristiċi Speċjali: 3 quick-change tips, articulated handle, fast heat-up time.
- Approximate Operating Temperature (Cutting Wire): 180 °C
- Approximate Operating Temperature (Blade/Engraving Tip): 320 °C
10. Garanzija u Appoġġ
Specific warranty information for the TOOLCRAFT TC-FC-USB Polystyrene Cutter is not provided in this manual. For details regarding warranty coverage, technical support, or replacement parts, please refer to the documentation included with your purchase or contact TOOLCRAFT customer service directly through their official webjew il-bejjiegħ bl-imnut tiegħek.
