1. Introduzzjoni
The Keeley Caverns V2 is a dual-effect pedal designed to combine delay and reverb functionalities into a single, compact unit. It features an analog-style tape delay with modulation options and versatile reverb modes. This manual provides detailed instructions for setup, operation, and maintenance of your Caverns V2 pedal.
Karatteristiċi ewlenin:
- 650ms Delay with Modulation
- Spring, Shimmer, and Modulated Reverb options
- Switchable True-Bypass or Trails operation
- Compact design suitable for various pedalboard setups
- Designed for 9V Center Negative power supply (not included)
- 9V Battery Compatible (battery not included)
Immaġni: Quddiem view of the Keeley Caverns V2 pedal, showcasing its white enclosure and control knobs.
2. Setup
Rekwiżiti tal-Enerġija:
The Caverns V2 pedal requires a 9V DC power supply with a center-negative polarity. Ensure your power supply meets these specifications to prevent damage to the unit. The pedal is also compatible with a 9V battery (not included).
- Voltage: 9 Volts DC
- Polarità: Ċentru Negattiv
- Tlugħ kurrenti: 75mA+ (minimum)
Konnessjonijiet:
Connect your instrument to the "IN" jack and your amplifier or next pedal in the signal chain to the "OUT" jack. Both are standard 1/4-inch audio jacks.
- Connect a 9V DC center-negative power supply to the power input jack (9VDC).
- Connect your guitar or other instrument to the "IN" jack.
- Qabbad il-jack "OUT" mal- ampl-input tal-lifer jew l-input tal-pedala li jmiss fil-katina tas-sinjali tiegħek.
Immaġni: Fuq view of the Keeley Caverns V2 pedal, showing the input (IN), output (OUT), and power (9VDC) jacks.
3. It-Tħaddim tal-Pedala
The Caverns V2 features independent controls for its Reverb and Delay sections, allowing for versatile sound shaping. Refer to the diagram below for control identification.
Image: Detailed diagram of the Keeley Caverns V2 pedal's controls, with each knob and switch numbered for reference.
Deskrizzjonijiet tal-Kontrolli:
| Nru. | Kontroll | Funzjoni |
|---|---|---|
| 1 | Reverb Blend | Adjusts the mix of the wet (effected) reverb signal with the dry (unaffected) signal. Turn clockwise for more reverb. |
| 2 | Reverb Decay | Controls the length of the reverb tail. Higher settings result in longer, more expansive reverb. |
| 3 | Reverb Warmth | Shapes the tone of the reverb, adding warmth or brightness. |
| 4 | Reverb Rate / Shimmer | Controls the modulation rate for the Modulated Reverb mode. In Shimmer mode, this knob adjusts the intensity of the shimmer effect. |
| 5 | Delay Blend | Adjusts the mix of the wet (effected) delay signal with the dry (unaffected) signal. Turn clockwise for more delay. |
| 6 | Ħin ta' Dewmien | Sets the delay time, from short slap-back echoes to long, atmospheric repeats (up to 650ms). |
| 7 | Dewmien Ripeti | Controls the number of delay repeats. From a single echo to infinite oscillation. |
| 8 | Delay Rate | Adjusts the rate of the modulation applied to the delay repeats. |
| 9 | Reverb Mode Switch | Selects the reverb type: Shimmer ('il fuq), Rebbiegħa (middle), or Modulati (down). |
| 10 | Delay Modulation Switch | Selects the delay modulation intensity: Dawl ('il fuq), Mitfi (middle), or Fond (down). |
| 11 | Reverb Footswitch | Activates or deactivates the Reverb effect. The LED indicates status (on/off). |
| 12 | Dewmien Footswitch | Activates or deactivates the Delay effect. The LED indicates status (on/off). |
True-Bypass vs. Trails Mode:
The Caverns V2 offers a switchable True-Bypass or Trails mode. In Trails mode, the reverb and delay tails naturally decay after the effect is disengaged, providing a smoother transition. In True-Bypass mode, the effect cuts off immediately when disengaged, preserving signal integrity when the pedal is off.
To switch between modes, consult the internal dip switches or the manufacturer's official documentation for the specific procedure. This setting is typically located inside the pedal enclosure and requires careful handling.
4. Manutenzjoni
To ensure the longevity and optimal performance of your Keeley Caverns V2 pedal, follow these maintenance guidelines:
- Tindif: Use a soft, dry cloth to clean the pedal's exterior. Avoid abrasive cleaners or solvents, which can damage the finish or internal components.
- Ħażna: Aħżen il-pedala f'post frisk u niexef 'il bogħod mix-xemx diretta, temperaturi estremi, u umdità għolja.
- Qawwa: Always use the correct power supply (9V DC, center-negative) to prevent electrical damage. Disconnect power when the pedal is not in use for extended periods.
- Konnessjonijiet: Iċċekkja perjodikament il-konnessjonijiet tal-kejbil kollha għal xedd u kedd. Kun żgur li l-ġakkijiet huma ħielsa mit-trab u l-fdalijiet.
- Evita Xokk Fiżiku: Protect the pedal from drops or impacts, which can damage internal circuitry or external components.
5 Issolvi l-problemi
If you encounter issues with your Caverns V2 pedal, refer to the following common troubleshooting steps:
- Ebda Ħsejjes:
- Ensure the power supply is correctly connected and providing the specified 9V DC center-negative power.
- Check all instrument cables. Try different cables to rule out faulty connections.
- Verify that both the Reverb and Delay footswitches are engaged (LEDs lit) if you expect an effect.
- Ensure the Blend knobs for both effects are not set to minimum (fully dry).
- Ħoss/Ħoss mhux mixtieq:
- Use a high-quality, isolated power supply. Daisy-chaining power supplies can sometimes introduce noise.
- Iċċekkja għal ground loops fil-katina tas-sinjali tiegħek.
- Kun żgur li l-kejbils kollha huma protetti kif suppost u f'kundizzjoni tajba.
- Mexxi l-pedala 'l bogħod mit-transformers tal-enerġija jew minn sorsi oħra ta' interferenza elettromanjetika.
- Effett Mhux Ingaġġanti:
- Confirm the footswitch is fully pressed and the corresponding LED illuminates.
- If in Trails mode, ensure the effect is not simply decaying from a previous engagement.
If these steps do not resolve the issue, please contact Keeley Electronics customer support for further assistance.
6. Speċifikazzjonijiet
| Attribut | Dettall |
|---|---|
| Numru tal-Mudell | KCav2 |
| Tip ta 'Effett | Delay and Reverb with Modulation |
| Rekwiżit ta' Enerġija | 9V DC Center Negative, 75mA+ Power Supply Required |
| Kompatibilità tal-Batterija | Batterija ta' 9V (mhux inkluża) |
| Input/Output | Mono Instrument Input, Mono Instrument Output (1/4 inch audio) |
| Format tas-Sinjal | Analogu |
| Dimensjonijiet (L x W x H) | 6.75" x 4.3" x 3.25" (madwar) |
| Piż tal-oġġett | 1.02 liri (madwar) |
| Materjal tal-Korp | Metall, plastik |
| Kulur | Abjad |
7. X'hemm fil-Kaxxa
Upon unboxing your Keeley Caverns V2 pedal, you should find the following components:
- Keeley Caverns V2 Reverb and Delay Pedal
- 2 Footswitches (integrated into the pedal)
- (Note: Power supply and 9V battery are not included and must be purchased separately.)
8. Garanzija u Appoġġ
Keeley Electronics products are built with quality and reliability in mind. For information regarding the product warranty, please refer to the official Keeley Electronics website or contact their customer support directly. Warranty terms typically cover manufacturing defects for a specified period from the date of purchase.
For technical support, troubleshooting beyond this manual, or warranty claims, please visit the Ħanut tal-Elettronika Keeley fuq Amazon jew l-uffiċjal tagħhom websit.
Image: Official logo of Keeley Electronics.
