ZeroWater 30 Cup Ready-Pour 5-stage Water Filter Dispenser Instruction Manual

1. Introduzzjoni

This manual provides detailed instructions for the setup, operation, and maintenance of your ZeroWater 30 Cup Ready-Pour 5-stage Water Filter Dispenser. Please read all instructions carefully before using the product.

Figure 1: ZeroWater 30 Cup Ready-Pour 5-stage Dispenser tal-Filtru tal-Ilma

2. Prodott Aktarview

The ZeroWater 30 Cup Ready-Pour 5-stage Water Filter Dispenser is designed to provide purified water by reducing total dissolved solids (TDS). It features a 5-stage filtration system and is NSF Certified to reduce lead, chromium, PFOA/PFOS, and mercury.

• Kapaċità: 30-il Tazza (7.1 Litri)
• Filtrazzjoni: 5-stage advanced filtration system
• Ċertifikazzjoni: NSF Certified to reduce lead, chromium, PFOA/PFOS, and mercury.
• Inklużi: Free TDS Meter for water quality testing.
• Dimensjonijiet: 15"T x 5.5"W x 10.62"Għ

Figure 2: Dispenser Features and Dimensions

Figura 3: 5-Stage Proċess ta' Filtrazzjoni

Figure 4: NSF Certification Details

3. Setup

1. Ħoll il-Komponenti: Neħħi b'attenzjoni l-partijiet kollha mill-imballaġġ.
2. Tindif Inizjali: Wash the dispenser reservoir, lid, and other non-filter components with warm water and mild dish soap. Rinse thoroughly. Rinse the outside of the filter shell under running water for approximately 30 seconds.
3. Installa l-Filtru: Insert the filter into the designated opening in the reservoir. Twist the filter clockwise until it is securely locked into position.
4. Activate TDS Meter: Remove the plastic tab from the battery compartment of the included TDS meter to activate it. Dock the TDS meter into the slot above the spigot with the screen facing outwards.
5. Imla l-ġibjun: Replace the top lid. Slide open the small lid on top and fill the reservoir with cool or room temperature tap water. Allow the water to filter through to the main dispenser compartment.

Setup Video Guide

Video 1: Official guide on how to set up your ZeroWater dispenser, including cleaning, filter installation, and TDS meter activation.

4. Istruzzjonijiet Operattivi

1. Dispensing Ilma: Place a glass or container under the spigot. Push the lever on the spigot to dispense filtered water. Release the lever to stop the flow.
2. Checking Water Quality: The docked TDS meter will display the Total Dissolved Solids level of the filtered water. A reading of 000 PPM indicates purified water.

Figure 5: TDS Meter Displaying 000 PPM

Figure 6: TDS Meter Controls

5. Manutenzjoni

1. Sostituzzjoni tal-filtru: Change your filter when the TDS meter reading is 006 or higher. To replace, remove the top lid and the old filter by twisting it counter-clockwise. Insert a new filter and twist clockwise until secure.
2. Cleaning the Dispenser: Regularly clean the dispenser reservoir and lid with warm water and mild dish soap. Rinse thoroughly to prevent residue buildup. The filter itself should not be cleaned with soap.

Figure 7: When to Change Your Filter

6 Issolvi l-problemi

• Filtrazzjoni bil-mod: If water filters slowly, the filter may be nearing the end of its life or may have air trapped. Try gently shaking the filter or replacing it if the TDS reading is high.
• High TDS Reading (006 or higher): This indicates the filter is exhausted and needs to be replaced to ensure optimal water purification.
• Tnixxijiet: Ensure all components, especially the filter and spigot, are securely tightened and properly seated. Check for any cracks in the plastic.

7. Speċifikazzjonijiet

8. Garanzija u Appoġġ

For warranty information or product support, please refer to the documentation included with your purchase or visit the official ZeroWater websit.