BLS T01L LED Closet Light User Manual

1. Introduzzjoni

The BLS T01L LED Closet Light is a versatile, motion-sensing lighting solution designed for various indoor applications. It features 20 super bright LEDs, offering 180 lumens of soft white light. This light can be powered by 3 AA batteries for wireless operation or via a 5V USB DC input for constant lighting. Its adjustable light beam and motion sensor provide customizable illumination and detection.

Image 1.1: The BLS T01L LED Closet Light, a 14-inch white light bar with a central motion sensor.

2. X'hemm fil-Kaxxa

Jekk jogħġbok ivverifika li l-komponenti kollha huma preżenti meta tiftaħ il-pakkett:

• 1 x BLS Under Cabinet Light (Model T01L)
• 1 x DC Cable
• 2 x Tejpijiet Adeżivi 3M
• 1 x Manwal tal-Istruzzjonijiet (dan id-dokument)

Image 2.1: The BLS T01L LED Closet Light shown with its packaging, DC cable, and mounting accessories.

3. Speċifikazzjonijiet

4. Setup u Installazzjoni

Follow these steps to set up your BLS T01L LED Closet Light:

4.1. It-Tħaddim tal-Apparat

The light can be powered by 3 AA batteries or a 5V USB DC input.

1. Installazzjoni tal-batterija:
   • Sib il-kompartiment tal-batterija fuq wara tad-dawl.
   • Gently push to open the center part of the battery compartment cover.
   • Insert three AA batteries (not included). One battery slides into the hole on the left, the second into the hole on the right, and the third goes into the open center between the first two. Ensure correct polarity (+/-).
   • Agħlaq l-għatu tal-kompartiment tal-batterija sew.
2. USB DC Power:
   • Connect the provided DC cable to the light's DC input port.
   • Plug the other end of the DC cable into a 5V USB power source (e.g., USB wall adapter, power bank).
   • Nota: If using USB DC power, it is recommended to remove the AA batteries to prevent potential issues or unnecessary battery drain.

Image 4.1: Diagram illustrating the 14-inch length of the light and its power options: 3 AA batteries or USB cable.

4.2. Immuntar tad-Dawl

The BLS T01L offers multiple installation options:

• Immuntar adeżiv: Peel the backing from the 3M adhesive tapes and firmly press the light onto a clean, dry surface.
• Immuntar bil-kamin: Use the provided screws to secure the light to the desired surface. This method offers a more permanent installation.

The light can be mounted either horizontally or vertically, depending on your application needs.

Image 4.2: Diagram showing horizontal and vertical installation options using screws or 3M adhesive stickers.

5. Istruzzjonijiet Operattivi

5.1. Għażla tal-Mod

The light features a slide switch with three modes:

• Modalità AUTO: The light will automatically turn on when motion is detected within 10 feet in a dark environment. It will remain on for 20 seconds after motion ceases. The built-in light sensor ensures it only activates when ambient light is low (e.g., at night).
• Modalità ON: Id-dawl jibqa' mixgħul kontinwament, irrispettivament mill-moviment jew mill-kundizzjonijiet tad-dawl ambjentali.
• Modalità OFF: Id-dawl se jibqa' mitfi.

5.2. Adjusting Motion Sensor Sensitivity

The motion sensor can be adjusted to modify its detection sensitivity and range:

• The motion sensor module is designed to swivel. Gently rotate the sensor to adjust its detection angle.
• This allows you to fine-tune the area where motion is detected, preventing unwanted activations.

Image 5.1: Illustration of how to adjust the motion sensor to control sensitivity.

5.3. Aġġustament tal-Angolu tar-Raġġ tad-Dawl

The entire light fixture can be adjusted to direct the light beam as desired:

• The light is mounted on a bracket that allows it to swivel.
• Gently pivot the light to achieve the desired illumination angle (e.g., 90°, 120°, 180°).

Immaġni 5.2: Eż.amples of adjustable light beam angles (90°, 120°, 180°) for optimal illumination.

6. Manutenzjoni

6.1. Sostituzzjoni tal-batterija

When the light output diminishes or the motion sensor becomes less responsive, it may be time to replace the batteries.

1. Open the battery compartment cover as described in Section 4.1.
2. Neħħi l-batteriji AA qodma.
3. Insert three new AA batteries, ensuring correct polarity.
4. Agħlaq l-għatu tal-kompartiment tal-batterija.

Nota: For optimal performance and to avoid frequent battery changes, consider using high-quality alkaline or rechargeable AA batteries. If using the USB DC power option, remove the AA batteries.

6.2. Tindif

To maintain the appearance and functionality of your light:

• Ensure the light is in the OFF position or disconnected from power before cleaning.
• Imsaħ il-wiċċ b'ċarruta ratba u niexfa.
• Do not use abrasive cleaners, solvents, or harsh chemicals, as these may damage the finish or electronic components.

7 Issolvi l-problemi

If you encounter issues with your BLS T01L LED Closet Light, refer to the following common problems and solutions:

8. Informazzjoni dwar Garanzija

The BLS T01L LED Closet Light comes with an extended warranty. For specific details regarding warranty coverage, terms, and conditions, please refer to the warranty card included with your product or contact BLS customer support.

9. Appoġġ għall-Klijent

If you have any questions, require technical assistance, or need further support, please contact BLS customer service through the following channels:

• Email: Refer to your product packaging or the official BLS websit għall-aktar email ta' kuntatt riċenti.
• Websit: Visit the official BLS websit għal FAQs u riżorsi ta' appoġġ.
• Amazon Store: Tista 'wkoll iżżur il- BLS Store on Amazon għal informazzjoni dwar il-prodott u għażliet ta' kuntatt għall-bejjiegħ.