Manwal tal-Utent tal-Pompa tal-Filtru Steinbach SPS 50-1T

1. Introduzzjoni

This manual provides essential instructions for the safe and efficient operation, installation, and maintenance of your Steinbach SPS 50-1T self-priming filter pump. Please read this manual thoroughly before operating the pump to ensure proper function and longevity of the product. This filter pump is designed for use with swimming pools up to approximately 22,000 liters water content.

2. Istruzzjonijiet tas-Sigurtà

Importanti: Always disconnect the pump from the power supply before performing any installation, maintenance, or cleaning tasks.

• Ensure the power supply matches the pump's specifications (230V/250W).
• The pump must be installed on a stable, level surface, protected from direct weather exposure.
• Tħaddimx il-pompa jekk il-korda tal-enerġija jew il-plagg ikunu bil-ħsara.
• Keep children and unauthorized persons away from the pump during operation.
• Never run the pump dry. Ensure the pump is filled with water before starting.
• The maximum water temperature for operation is 35°C.
• All electrical connections should be performed by a qualified electrician and comply with local regulations.

3. Prodott Aktarview u Komponenti

The Steinbach SPS 50-1T is a self-priming filter pump equipped with a pre-filter and an integrated timer. Familiarize yourself with the main components:

Figura 1: B'mod ġenerali view of the Steinbach SPS 50-1T filter pump, showing the motor, pump housing, pre-filter, and control panel.

• Mutur: The electrical unit that drives the pump impeller.
• Djar tal-Pompa: Contains the impeller and directs water flow.
• Filtru minn qabel: A transparent chamber with a removable basket designed to capture larger debris before it reaches the pump impeller, protecting the pump from damage.
• Konnessjonijiet tad-Dħul/Ħruġ: Points for connecting hoses (Ø 32/38 mm).
• Panel tal-Kontroll: Features ON/OFF and TIMER buttons, along with indicator lights for setting operation duration.

Figura 2: Dettaljati view of the pre-filter assembly, showing the transparent lid and the hose connection point for the inlet.

Figura 3: The pump's control panel, featuring the ON/OFF button, TIMER button, and indicator lights for setting operational hours.

4. Setup u Installazzjoni

1. Pjazzament: Position the pump on a firm, level surface, ideally below the water level of the pool for easier priming. Ensure it is protected from rain and direct sunlight.
2. Konnessjonijiet tal-manka: Connect the pool's skimmer line to the pump's inlet (pre-filter side) and the return line to the pump's outlet. Use hoses with a diameter of Ø 32/38 mm. Secure all connections with hose clamps biex jipprevjenu tnixxijiet.
   

   Figura 4: View of the threaded inlet and outlet ports on the pump, ready for hose adapters.
3. Ipprajmjar il-Pompa: Before starting, ensure the pre-filter is filled with water. If the pump is above water level, it may require manual priming by filling the pre-filter chamber until water flows into the pump housing.
4. Konnessjoni Elettrika: Plug the pump into a grounded electrical outlet (230V). Ensure the outlet is protected by a Residual Current Device (RCD) for safety.

5. Istruzzjonijiet Operattivi

Ladarba tkun installata u pprajmata, il-pompa tkun lesta għall-operazzjoni.

5.1 Operazzjoni manwali

• Agħfas il- ON/OFF button on the control panel to start the pump.
• Agħfas il- ON/OFF button again to stop the pump.

5.2 Funzjoni Timer

The integrated timer allows for automated operation cycles.

1. Ensure the pump is connected to power.
2. Agħfas il- TIMER button repeatedly to select the desired operating duration (e.g., 2, 4, 6, 8, 10, 12, 14, 16, 24 hours). The corresponding indicator light will illuminate.
3. The pump will start and run for the selected duration, then automatically shut off.
4. The timer cycle will repeat daily at the same time it was initially set. To reset the timer, unplug the pump for a few seconds and then plug it back in.

6. Manutenzjoni

Regular maintenance ensures optimal performance and extends the lifespan of your pump.

6.1 Cleaning the Pre-filter Basket

1. Skonnettja l-pompa mill-provvista tal-enerġija.
2. Close any valves to prevent water flow from the pool.
3. Unscrew the transparent lid of the pre-filter.
4. Remove the pre-filter basket and clean it thoroughly under running water.
5. Inspect the O-ring seal on the lid for damage and ensure it is clean.
6. Replace the basket, secure the lid, and open the valves.
7. Erġa' ħejji l-pompa jekk meħtieġ qabel ma terġa' tibdaha.

Figura 5: The pre-filter chamber with its transparent lid removed, showing the internal basket for debris collection.

6.2 Winterization

• At the end of the swimming season, disconnect the pump from power and drain all water from the pump and hoses to prevent freezing damage.
• Clean the pump thoroughly and store it in a dry, frost-free location.

7 Issolvi l-problemi

8. Speċifikazzjonijiet Tekniċi

9. Garanzija u Appoġġ

For warranty information, technical support, or spare parts, please refer to the documentation provided with your purchase or contact Steinbach customer service. Keep your proof of purchase for warranty claims.

You can find more information and contact details on the official Steinbach websit: www.steinbach.at