Manwal tal-Utent tad-Ditekter tas-Saqaf b'Teknoloġija Doppja RISCO RK150DTG300B

1. Introduzzjoni

This manual provides essential information for the proper installation, operation, and maintenance of your RISCO RK150DTG300B Dual Technology Ceiling Detector. This advanced security device offers 360° coverage, combining passive infrared (PIR) and microwave (MW) technologies for reliable motion detection in various environments.

For optimal performance and safety, please read this manual thoroughly before installation and use. Keep it for future reference.

2. Informazzjoni dwar is-Sigurtà

WARNING: Risk of electric shock. Installation should only be performed by qualified personnel.

• Skonnettja l-enerġija qabel ma twettaq kwalunkwe installazzjoni jew manutenzjoni.
• Kun żgur li l-wajers kollha jikkonformaw mal-kodiċijiet u r-regolamenti elettriċi lokali.
• Tesponix l-apparat għall-umdità, temperaturi estremi, jew dawl tax-xemx dirett.
• Dan l-apparat huwa ddisinjat għall-użu fuq ġewwa biss.
• Tampering with the device may void the warranty and compromise security.

3. Kontenut tal-Pakkett

Ivverifika li l-oġġetti kollha huma preżenti fil-pakkett:

• RISCO RK150DTG300B Dual Technology Ceiling Detector Unit
• Ħardwer tal-Immuntar (viti, ankri)
• Manwal għall-Utent (dan id-dokument)

Figura 1: Quddiem view of the RISCO RK150DTG300B Dual Technology Ceiling Detector.

4. Setup u Installazzjoni

The RK150DTG300B is designed for ceiling mounting to provide optimal 360° detection coverage.

4.1. L-Għażla tas-Sit

• Choose a central location on the ceiling within the area to be protected.
• Avoid mounting near heat sources, air conditioning vents, or areas with significant air drafts that could cause false alarms.
• Kun żgur li ż-żona ta' skoperta hija ħielsa minn ostakli kbar.

4.2. Immuntar tad-Ditekter

1. Carefully separate the detector's base from its cover.
2. Position the base on the chosen ceiling location and mark the drilling points.
3. Drill holes and insert appropriate anchors if necessary.
4. Secure the detector base to the ceiling using the provided screws.

Figura 2: Eżample of detector mounting points and internal components.

4.3. Il-wajers

The RK150DTG300B is powered by an electrical cable. Connect the detector to your security system's control panel according to the panel's instructions and the detector's terminal markings.

• Konnessjoni tal-Enerġija: Qabbad il-wajers tal-provvista tal-enerġija mat-terminals indikati.
• Riżultat ta 'allarm Connect the alarm output to the appropriate zone input on your control panel.
• Tamper Output: Qabbad it-tamper output to a 24-hour tamper zone on your control panel. The detector features anti-removal and anti-opening tamper protezzjoni.
• EOL Resistors: Integrated End-Of-Line (EOL) resistors are selectable via jumpers. Refer to your control panel's manual for the required EOL resistor values and configure the detector accordingly.

4.4. Configuration and Testing

• Anti-Cloak Technology (ACT): This feature enhances detection capabilities by identifying attempts to mask the infrared signal.
• Green Line Feature: Allows for the deactivation of the microwave (MW) channel when the security system is disarmed, reducing power consumption and potential interference. This is typically configured during installation.
• Test tal-Mixja: After installation, perform a walk test to verify the detector's coverage and sensitivity. Walk through the entire protected area to ensure the detector triggers an alarm. Adjust sensitivity if necessary (refer to specific jumper settings or potentiometers if available on the device, though not explicitly detailed in product description).

5. It-tħaddim tad-Detector

The RISCO RK150DTG300B operates automatically once properly installed and powered. It continuously monitors the protected area using its dual technology sensors.

• Teknoloġija Doppja: The detector combines Passive Infrared (PIR) and Microwave (MW) detection. Both technologies must typically be triggered simultaneously to generate an alarm, significantly reducing false alarms.
• Kopertura 360°: The ceiling mount design provides a full 360-degree detection pattern, covering an area up to 13 meters in diameter.
• Tamper Protezzjoni: The integrated anti-removal and anti-opening tamper switches will trigger an alarm if the detector is tampered with or forcibly removed from its mounting location.

6. Manutenzjoni

To ensure the long-term reliability and performance of your detector, follow these maintenance guidelines:

• Tindif: Periodically clean the detector's lens and housing with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Ittestjar regolari: Perform a walk test at least once a year, or as recommended by your security system provider, to confirm proper operation.
• Spezzjoni: Visually inspect the detector for any signs of damage or loose connections.

7 Issolvi l-problemi

If you experience issues with your RK150DTG300B detector, refer to the following common problems and solutions:

If troubleshooting steps do not resolve the issue, contact your security system installer or RISCO technical support.

8. Speċifikazzjonijiet

9. Garanzija u Appoġġ

For warranty information, please refer to the terms and conditions provided by your point of purchase or contact RISCO Group directly. RISCO Group products are typically covered by a limited warranty against defects in materials and workmanship.

For technical support, installation assistance, or further inquiries, please contact your authorized RISCO installer or visit the official RISCO Group websit għal riżorsi ta' appoġġ.

Manifattur: RISCO Group

Websit: www.riscogroup.com