Stetsom Vulcan 9K EQ - 1 Ohm 9000W RMS Firxa Sħiħa Qawwa Għolja AmpManwal ta 'l-Utent aktar ħaj

Introduzzjoni

Thank you for choosing the Stetsom Vulcan 9K EQ - 1 Ohm 9000W RMS Full Range High Power Amplifier. Dan il-manwal jipprovdi informazzjoni essenzjali għall-installazzjoni, it-tħaddim u l-manutenzjoni xierqa tal-apparat tiegħek amplifier. Jekk jogħġbok aqra dan il-manwal bir-reqqa qabel ma tuża l-prodott biex tiżgura prestazzjoni u sigurtà ottimali.

Informazzjoni Importanti dwar is-Sigurtà

• Dejjem skonnettja l-batterija tal-vettura qabel ma tagħmel xi konnessjonijiet elettriċi.
• Żgura ertjar xieraq biex tevita perikli elettriċi.
• Installa l- amplifier f'żona b'ventilazzjoni tajba biex jipprevjeni sħana żejda.
• Use appropriate gauge wiring for power and speaker connections as specified in this manual.
• Evita li tesponi l- amplifier għall-umdità jew temperaturi estremi.
• Tippruvax tiftaħ jew isewwi l- ampIrreferi kull servizz lil persunal kwalifikat.

Prodott Overview

The Stetsom Vulcan 9K EQ is a high-power, full-range digital amplifier designed for automotive audio systems. It features a robust design and advanced equalization capabilities to deliver powerful and clear sound reproduction.

Karatteristiċi ewlenin:

• 9000W RMS power output at 1 Ohm (12.6V)
• Full Range frequency response (10Hz to 15KHz)
• Built-in 3-band equalizer (Bass, Mid Bass, Mid High)
• Over Clip +15% Power indicator
• Protection circuits for safe operation

Identifikazzjoni tal-Komponent:

Il- amplifier features power, protection, and clip indicators on the front panel. The input and output terminals are located on the side for easy access during installation.

Installazzjoni u Setup

1. Konnessjonijiet tal-Enerġija:

• Power Cable (B+): Connect a heavy-gauge power cable directly from the positive terminal of the vehicle's battery to the B+ terminal on the amplifier. An inline fuse or circuit breaker (not included) must be installed within 18 inches (45 cm) of the battery.
• Ground Cable (GND): Qabbad kejbil tal-ert oħxon mit-terminal GND fuq amplifier to a clean, unpainted metal surface of the vehicle chassis. Ensure a solid, low-resistance connection.
• Tixgħel mill-Bogħod (REM): Qabbad wajer ta' tixgħel mill-bogħod mill-output remot tal-unità ewlenija tiegħek mat-terminal REM fuq amplififikatur. Dan il-wajer jagħti sinjal lill- amplifer biex jixgħel u jitfi mas-sistema awdjo tiegħek.

2. Audio Input Connections:

Connect RCA cables from your head unit's pre-out (RCA output) to the RCA input jacks on the amplifier. Ensure correct left and right channel connections if applicable, though this is a mono ampaktar ħaj.

3. Speaker Output Connections:

Connect your subwoofer(s) or full-range speakers to the speaker output terminals on the amplifier. Pay close attention to polarity (+ and -) and ensure the total impedance of your speakers matches the amplifier's rated impedance (1 Ohm for this model). Refer to the specifications section for impedance details.

4. Immuntar:

Immonta l- amplifier securely in a location that provides adequate ventilation and protection from moisture. Avoid mounting it directly on carpet or in enclosed spaces without airflow.

Istruzzjonijiet Operattivi

1. L-Ewwel Tixgħil:

After all connections are made, reconnect the vehicle's battery. Turn on your head unit. The "POWER" indicator on the amplifier should illuminate, indicating it is receiving power and is operational.

2. Aġġustament tal-Qligħ:

Aġġusta l-kontroll tal-gwadann fuq il- amplifer biex jaqbel mal-volum tal-ħruġtage of your head unit. Start with the gain at its minimum setting. Play a familiar track at about 75% of your head unit's maximum volume. Slowly increase the amplifier's gain until you hear distortion, then back it off slightly. The "CLIP" indicator should only flash briefly on very dynamic peaks, not stay illuminated.

3. Crossover Settings:

The Vulcan 9K EQ features adjustable crossovers:

• Filtru Low Pass (LPF): Adjust this control to set the upper frequency limit for your subwoofers. Frequencies above this setting will be attenuated.
• Filtru High Pass (HPF): Adjust this control to set the lower frequency limit for your speakers. Frequencies below this setting will be attenuated. This is typically used for full-range speakers or mid-bass drivers.

Refer to your speaker manufacturer's recommendations for optimal crossover points.

4. Equalizer Adjustment (3-Band EQ):

Il- amplifier includes a 3-band equalizer to fine-tune the audio output:

• Bass: Jaġġusta r-rispons ta' frekwenza baxxa.
• Mid Bass: Adjusts the mid-low frequency response.
• Nofs Għoli: Adjusts the mid-high frequency response.

Make small adjustments and listen carefully to achieve your desired sound balance. Avoid excessive boosting, which can lead to distortion or speaker damage.

Manutenzjoni

• Żomm il- ampIl-lavatur ikun nadif u ħieles mit-trab u l-fdalijiet. Uża drapp artab u niexef għat-tindif.
• Kun żgur li jkun hemm fluss ta' arja adegwat madwar amplifier at all times to prevent overheating. Regularly check that cooling fins are not obstructed.
• Periodically check all wiring connections for tightness and corrosion. Loose connections can cause performance issues or damage.

Gwida dwar is-sejbien ta 'problemi

Speċifikazzjonijiet Tekniċi

Garanzija u Appoġġ

Stetsom products are manufactured to the highest quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Stetsom website. For technical support or service inquiries, please contact your authorized Stetsom dealer or Stetsom customer service.

Websit: www.stetsom.com.br (Eżampil-link, il-link attwali jista' jvarja)