Rev-A-Shelf LD-0220-50SC Soft-Close Pivot Hinges Instruction Manual

Introduzzjoni

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Rev-A-Shelf LD-0220-50SC Soft-Close Pivot Hinges. Please read this manual thoroughly before installation and retain it for future reference.

Informazzjoni dwar is-Sigurtà

Dejjem ilbes tagħmir tas-sigurtà xieraq, inkluż protezzjoni għall-għajnejn, waqt l-installazzjoni.
Ensure all tools are in good working condition.
Żomm partijiet żgħar 'il bogħod mit-tfal biex tevita perikli ta' fgar.
Jekk m'intix ċert dwar xi pass, ikkonsulta professjonist kwalifikat.

Kontenut tal-Pakkett

(1) Left Soft-Close Pivot Hinge
(1) Right Soft-Close Pivot Hinge
(1) Pakkett tal-Viti

Image: A pair of Rev-A-Shelf LD-0220-50SC Soft-Close Pivot Hinges, showing the spring-loaded mechanism and mounting plates.

Speċifikazzjonijiet

Karatteristika	Dettall
Numru tal-Mudell	LD-0220-50SC
Materjal	Metall
Tip Finish	Mhux mitmuma
Tip ta 'Immuntar	Face Mount
Angolu tal-Ftuħ	50-grad
Dimensjonijiet (W x D x H)	1" (26 mm) W x 2-5/8" (67 mm) D x 3-7/8" (99 mm) H
Komponenti Inklużi	(1) Left hinge, (1) right hinge, and screw pack

Setup u Installazzjoni

Proper installation is key to the smooth operation of your soft-close pivot hinges. Follow these steps carefully.

1. Measure Your Cabinet Opening

Before installing, accurately measure the width, height, and depth of your cabinet opening. This ensures compatibility and proper fit for any accessories you plan to use with the tip-out tray.

Video: This video from Rev-A-Shelf provides guidance on how to measure your cabinet opening correctly for various products.

Video: This video explains how to measure and determine if your cabinet hinge is a 1/2" overlay, which is important for proper fit.

2. Ipprepara għall-Installazzjoni

Identify the left (L) and right (R) hinges.
Ensure you have all necessary tools: drill, 3/32 drill bit, pencil, and screwdriver.

3. Mark and Drill Holes on Face Frame

With the drawer front panel still installed (or aligned to its desired location), use a pencil to lightly mark its perimeter on the front of the face frame.
Remove the drawer front panel.
Place one hinge on the appropriate side of the face frame. Align it so the bottom rests on the face frame and the front is flush with the face frame's front.
Trace the locations of two mounting holes onto the frame. Avoid holes too close to the top or bottom edges for easier drilling.
Irrepeti għan-naħa l-oħra.
Drill the marked holes into the face frame using a 3/32 drill bit.

Rev-A-Shelf LD-0220-50SC Soft-Close Pivot Hinge installed in a cabinet

Image: A Rev-A-Shelf Soft-Close Pivot Hinge installed on the inside of a cabinet, with a tip-out tray partially open.

4. Attach Hinges to Face Frame

Attach the hinges to the face frame using the provided screws.

5. Mark and Drill Holes on Drawer Front Panel

Place the drawer front panel against the face frame in its desired location, using your previously traced perimeter as a guide.
From the inside of the cabinet, mark the mounting hole locations from the hinges onto the back of the drawer front panel.
Remove the panel and carefully drill the mounting holes with a 3/32 bit. Caution: Do not drill all the way through the panel. A drill bit stop collar is recommended.

Rev-A-Shelf LD-0220-50SC Soft-Close Pivot Hinge installed in a cabinet with tip-out tray

Image: A Rev-A-Shelf Soft-Close Pivot Hinge installed on the inside of a cabinet, with a tip-out tray open, showing the hinge mechanism.

6. Install Drawer Front Panel

Attach the drawer front panel to the installed hinges. This can be done from inside the cabinet with the hinges "closed" or from outside with them "open."
Do not fully tighten screws until all four are in place and the panel is aligned.

Close-up of Rev-A-Shelf LD-0220-50SC Soft-Close Pivot Hinge mechanism

Immaġni: Close-up view of the Rev-A-Shelf Soft-Close Pivot Hinge mechanism, demonstrating its movement.

7. Test and Adjust

Test the function of the tip-out tray.
If needed, slightly loosen the screws and adjust the panel to ensure it closes flush and evenly.

Video: This video demonstrates the installation and operation of the soft-close pivot hinges in a tip-out tray application.

Operazzjoni

The Rev-A-Shelf LD-0220-50SC hinges feature a 50-degree opening and a soft-close dampener mechanism. This allows the tip-out tray to open smoothly and close quietly, preventing slamming.

To open: Gently pull the top edge of the tip-out tray forward. The hinges will pivot, allowing access to the interior.
To close: Gently push the tip-out tray back into its closed position. The soft-close mechanism will engage, ensuring a quiet and controlled closure.

Video: This video illustrates the smooth operation of tip-out tray hinges, showcasing the soft-close feature.

Video: A short demonstration of a tilt-out tray hinge in operation, highlighting its functionality.

Manutenzjoni

These hinges are designed for durability and require minimal maintenance.

Tindif: Wipe the hinges periodically with a soft, damp cloth to remove dust and debris. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
Lubrikazzjoni: The hinges are pre-lubricated. If you notice any stiffness over time, a small amount of silicone-based lubricant can be applied to the pivot points.
Spezzjoni: Regularly check all screws to ensure they are tight. Re-tighten if necessary.

Issolvi l-problemi

Tray Not Closing Softly

Iċċekkja għal Ostruzzjonijiet: Ensure nothing is blocking the hinge mechanism or the path of the tray.
Ivverifika l-Installazzjoni: Re-check that the hinges are installed correctly and securely, and that the screws are not overtightened, which could impede movement.
Aġġusta l-Allinjament: Slight adjustments to the panel's alignment might be needed. Loosen mounting screws slightly, adjust the panel, and re-tighten.

Tray Not Opening Smoothly

Iċċekkja għal Fdalijiet: Clear any debris that might be caught in the hinge mechanism.
Lubrikazzjoni: Apply a small amount of silicone-based lubricant to the pivot points if the movement feels stiff.

Garanzija

Rev-A-Shelf LD-0220-50SC Soft-Close Pivot Hinges come with a Garanzija Limitata tul il-Ħajja. This warranty covers defects in material and workmanship under normal use. For specific details regarding warranty claims, please refer to the official Rev-A-Shelf websit jew ikkuntattja l-appoġġ tal-klijent.

Appoġġ

For further assistance, technical support, or to inquire about replacement parts, please visit the official Rev-A-Shelf websit jew ikkuntattja lid-dipartiment tas-servizz tal-konsumatur tagħhom.

Websit: www.rev-a-shelf.com

Servizz tal-Klijent: Irreferi għall- websit għad-dettalji tal-kuntatt.

	Istruzzjonijiet għall-Installazzjoni tat-Trejs Rev-A-Shelf Soft-Close Tip-Out Gwida pass pass għall-installazzjoni tat-trejs tip-out b'għeluq soft-close ta' Rev-A-Shelf fil-kabinetti tal-bażi tas-sink. Tinkludi l-għodda meħtieġa, lista tal-partijiet, u struzzjonijiet dettaljati għat-tħejjija tal-pannelli, l-immuntar taċ-ċappetti, u t-twaħħil tat-trejs.
	Istruzzjonijiet għall-Installazzjoni ta' Rev-A-Shelf Vanity/Base Cabinet Filler Gwida pass pass għall-installazzjoni tar-Rev-A-Shelf Vanity/Base Cabinet Filler, inklużi l-għodda meħtieġa, il-ħin tal-assemblaġġ, u pariri dwar il-manutenzjoni.
	Rev-A-Shelf HampIstruzzjonijiet għall-Installazzjoni tal-Flap Stay Gwida komprensiva għall-installazzjoni tar-Rev-A-Shelf Hamper Flap Stay, li fih lista tal-partijiet, l-għodda meħtieġa, u struzzjonijiet ta' assemblaġġ pass pass b'dijagrammi dettaljati deskritti fit-test.
	Gwida għall-Installazzjoni tat-Template taċ-Ċappetta Rev-A-Shelf Dan id-dokument jipprovdi mudell ta' ċappetta minn Rev-A-Shelf għal skopijiet ta' installazzjoni. Jinkludi struzzjonijiet u dijagrammi għat-twaħħil taċ-ċappetti.
	Gwida għall-Installazzjoni tat-Trej tal-Pożati Rev-A-Shelf Istruzzjonijiet komprensivi għall-installazzjoni għar-Rev-A-Shelf Cutlery Tray (Mudell I-CT-0825), li jiddettaljaw il-kejl, it-tirqim, u l-kura. Ittejjeb l-organizzazzjoni tal-kxaxen tal-kċina tiegħek b'din il-gwida.
	Istruzzjonijiet għall-Installazzjoni tal-Kit Rev-A-Shelf għall-Immuntar fuq il-Bieb Gwida komprensiva għall-installazzjoni tar-Rev-A-Shelf Door-Mount Kit, li tiddeskrivi l-partijiet, l-għodda, u l-assemblaġġ pass pass għall-bibien tal-kabinetti.