Manwal ta' Istruzzjoni

1. Introduzzjoni

This manual provides essential information for the proper use, installation, and maintenance of the Horiba 3200172800 Replacement Tungsten Turbidity Cell. This cell is designed as a direct replacement component for the Horiba U-53 Series meters, specifically compatible with Model #7801.

Please read this manual thoroughly before attempting any installation or operation to ensure safe and effective use of the product and to maintain the accuracy of your turbidity measurements.

2. Informazzjoni dwar is-Sigurtà

Dejjem osserva l-prekawzjonijiet ta' sigurtà li ġejjin biex tevita korrimenti u ħsara lill-istrument:

• Handle the turbidity cell with care. Avoid dropping or subjecting it to strong impacts.
• Ensure the U-53 Series meter is powered off and disconnected from any power source before installing or removing the turbidity cell.
• Do not attempt to disassemble the turbidity cell. Refer to qualified service personnel for repairs.
• Use only genuine Horiba replacement parts to ensure compatibility and optimal performance.
• Dispose of the old turbidity cell according to local environmental regulations.

3. Prodott Aktarview

The Horiba 3200172800 is a replacement tungsten turbidity sensor designed for use with the Horiba U-53 Series multi-parameter water quality meters, specifically for the Model 7800 turbidity measurement function.

Figure 3.1: The Horiba 3200172800 Replacement Tungsten Turbidity Cell. This image shows the black cylindrical sensor with a threaded base and a small metallic tip extending from one end, indicating its connection point.

Karatteristiċi ewlenin:

• Direct replacement for worn or damaged turbidity cells.
• Ensures accurate turbidity measurements when properly installed.
• Compatible with Horiba U-53 Series meters.

4. Setup u Installazzjoni

Follow these steps to replace the turbidity cell in your Horiba U-53 Series meter:

1. Itfi: Ensure the Horiba U-53 Series meter is completely powered off and disconnected from any power source.
2. Locate Old Cell: Identify the existing turbidity cell on your U-53 Series meter. Refer to your U-53 Series meter's instruction manual for specific location and removal procedures if unsure.
3. Remove Old Cell: Carefully unscrew or unclip the old turbidity cell from its housing. Be mindful of any residual liquid or debris.
4. Spezzjona l-Konnessjoni: Before installing the new cell, inspect the connection port on the U-53 meter for any dirt, moisture, or damage. Clean if necessary using a soft, dry cloth.
5. Installa Ċellula Ġdida: Align the new Horiba 3200172800 Replacement Tungsten Turbidity Cell with the connection port. Gently push and twist (if applicable) until it is securely seated. Do not overtighten if it is a threaded connection.
6. Ivverifika l-Konnessjoni: Ensure the cell is firmly attached and there is no wobble. A loose connection can lead to inaccurate readings or damage.
7. Qawwa Mixgħul: Reconnect power to the U-53 Series meter and power it on. Perform a calibration as per the U-53 Series meter's manual to ensure proper functionality with the new cell.

5. Konsiderazzjonijiet Operattivi

The Horiba 3200172800 Replacement Tungsten Turbidity Cell functions as an integral part of the Horiba U-53 Series meter. Its operation is directly controlled by the main meter unit.

• Kalibrazzjoni: After replacing the turbidity cell, it is crucial to perform a calibration of the turbidity sensor using the U-53 Series meter's calibration function and appropriate turbidity standards. Refer to your U-53 Series meter's manual for detailed calibration procedures.
• Kejl: Once calibrated, the turbidity cell will automatically provide readings when the U-53 Series meter is used for turbidity measurements. Ensure the cell is fully immersed in the sample liquid as required by the U-53 Series meter's operating instructions.
• Kundizzjonijiet Ambjentali: Operate the U-53 Series meter with the new cell within the environmental specifications outlined in the U-53 Series meter's manual to ensure accurate and reliable performance.

6. Manutenzjoni

Proper maintenance extends the life and ensures the accuracy of your turbidity cell:

• Tindif: After each use, especially when measuring turbid samples, gently rinse the turbidity cell with distilled or deionized water. Use a soft, lint-free cloth to carefully wipe the optical surfaces. Avoid abrasive materials or harsh chemicals that could scratch the sensor.
• Ħażna: When not in use, store the turbidity cell in a clean, dry, and temperature-controlled environment. Protect the optical surfaces from dust and scratches. It is recommended to store it in its original packaging or a protective case.
• Spezzjoni: Periodically inspect the cell for any signs of damage, scratches on the optical surfaces, or accumulation of residue. Replace the cell if significant damage is observed or if calibration becomes consistently difficult.

7 Issolvi l-problemi

If you encounter issues after replacing the turbidity cell, consider the following:

For issues not listed here or if problems persist, refer to the comprehensive troubleshooting guide in your Horiba U-53 Series meter's manual or contact Horiba customer support.

8. Speċifikazzjonijiet

9. Garanzija u Appoġġ

For detailed information regarding the warranty of the Horiba 3200172800 Replacement Tungsten Turbidity Cell, please refer to the warranty documentation provided with your original Horiba U-53 Series meter or contact Horiba customer support directly.

For technical assistance, service, or to order additional replacement parts, please visit the official Horiba website or contact their authorized distributors. Ensure you have your product model number (3200172800) and the serial number of your U-53 Series meter ready when contacting support.

Tista' ssib aktar informazzjoni u dettalji ta' kuntatt fuq Ħanut HORIBA fuq Amazon or the official Horiba websit.