Manwal tal-Istruzzjonijiet tal-Pompa tal-Ħasil tal-Windskrin ACI 377140

1. Prodott Aktarview

The ACI 377140 Windshield Washer Pump is engineered to meet or exceed Original Equipment (OE) performance standards. This pump is designed for reliable and durable operation, ensuring effective windshield cleaning. It features an OE-style electrical connector and is equipped with three nozzles for efficient fluid delivery.

Figura 1: ACI 377140 Windshield Washer Pump. This image shows the complete pump unit, including the main body, electrical connector at the top, and the fluid outlet with three nozzles at the bottom.

2. Karatteristiċi tal-prodott

OE Performance Matching: Engineered to match Original Equipment washer pumps for seamless integration and performance.
Direct Fit Design: Specifically designed to fit original windshield washer pump applications.
OE Style Electrical Connector: Ensures a secure and compatible electrical connection.
Three Nozzles: Equipped with three nozzles for effective and broad fluid distribution on the windshield.

3. Gwida għall-Installazzjoni

Installation of the ACI 377140 Windshield Washer Pump typically involves replacing the existing pump. While the process can vary by vehicle model, the general steps are outlined below. It is recommended to consult your vehicle's service manual for specific instructions related to your make and model.

Is-Sigurtà l-Ewwel: Ensure the vehicle is turned off and the parking brake is engaged. Disconnect the negative terminal of the battery to prevent electrical hazards.
Locate the Washer Reservoir: The windshield washer pump is usually located at the bottom of the windshield washer fluid reservoir. Access to the reservoir may require removing fender liners, bumper components, or other under-hood parts depending on the vehicle.
Drain Fluid: If possible, drain the washer fluid from the reservoir to minimize spillage during pump removal.
Skonnettja l-Konnettur Elettriku: Carefully disconnect the electrical connector from the old pump.
Remove Hoses: Disconnect the washer fluid hoses from the old pump. Be prepared for some fluid to leak out.
Neħħi l-Pompa l-Qadima: The pump is typically held in place by a rubber grommet or a clip. Gently pull or unclip the old pump from the reservoir.
Installa Pompa Ġdida: Insert the new ACI 377140 pump into the reservoir opening, ensuring it seats firmly in the grommet.
Reconnect Hoses and Electrical: Reattach the washer fluid hoses to the new pump and securely connect the electrical connector.
Refill Reservoir: Fill the washer fluid reservoir with appropriate windshield washer fluid.
Operazzjoni tat-Test: Reconnect the battery, turn on the vehicle, and test the windshield washer system to ensure proper function and check for leaks.

Note: Some vehicle designs may require significant disassembly of surrounding components to access the washer pump. Patience and proper tools are essential for a successful installation.

4. Istruzzjonijiet Operattivi

The ACI 377140 Windshield Washer Pump operates as part of your vehicle's existing windshield washer system. Once installed, its operation is integrated with your vehicle's controls.

Attivazzjoni: To activate the pump, use the windshield washer stalk or button inside your vehicle, typically located on the steering column. Refer to your vehicle's owner's manual for the exact control mechanism.
Fluid Delivery: Upon activation, the pump draws fluid from the reservoir and delivers it under pressure through the washer nozzles onto the windshield.
Wiper Activation: In most vehicles, activating the washer pump will also automatically engage the windshield wipers for a few cycles to clear the fluid and debris.

Ensure the washer fluid reservoir is adequately filled for optimal performance.

5. Manutenzjoni

The ACI 377140 Windshield Washer Pump is designed for durability and requires minimal direct maintenance. However, maintaining the overall windshield washer system will ensure the longevity and performance of the pump.

Livell tal-Fluwidu: Regularly check and maintain the windshield washer fluid level in the reservoir. Do not allow the reservoir to run dry, as this can cause the pump to run without lubrication and potentially shorten its lifespan.
Tip ta' fluwidu: Use only approved windshield washer fluid. Avoid using plain water, especially in freezing temperatures, as it can freeze and damage the pump or lines.
Isodd taż-żennuna: Periodically check the windshield washer nozzles for clogs. Clogged nozzles can increase back pressure on the pump, potentially leading to premature wear. Clear any blockages using a fine needle or pin.
Tnixxijiet tas-Sistema: Inspect hoses and connections for any signs of leaks. Leaks can reduce fluid pressure and cause the pump to work harder.

6 Issolvi l-problemi

If you experience issues with your windshield washer system after installing the ACI 377140 pump, consider the following troubleshooting steps:

Problema	Kawża Possibbli	Soluzzjoni
No fluid sprays or weak spray	Low or empty fluid reservoir. Clogged washer nozzles. Kinked or disconnected hose. Blown fuse for washer pump. Faulty electrical connection to pump. Pump motor issue (less likely if new).	Refill reservoir with appropriate fluid. Clear nozzles with a fine pin. Inspect and reattach/straighten hoses. Check and replace the relevant fuse in your vehicle's fuse box. Ensure electrical connector is securely attached to the pump. If all else fails, consult a professional mechanic.
Fluid leaks around pump area	Improperly seated pump grommet. Konnessjoni tal-pajp maħlula. Cracked reservoir or hose.	Ensure pump is fully seated in the reservoir grommet. Check and tighten hose clamps or connections. Inspect reservoir and hoses for damage; replace if necessary.
Il-pompa taħdem iżda l-ebda fluwidu	Empty reservoir. Arja fis-sistema. Severe clog in line or nozzles.	Refill reservoir. Run pump for a few seconds to prime the system. Inspect and clear all lines and nozzles.

7. Speċifikazzjonijiet

Attribut	Valur
Manifattur	ACI
Brand	ACI
Numru tal-Mudell tal-Oġġett	377140
Numru tal-Parti tal-Manifattur	377140
Piż tal-oġġett	3.2 uqija
Dimensjonijiet tal-Prodott	3.3 x 3.5 x 2.6 pulzieri
ASIN	B00FAMAEP4
Data L-Ewwel Disponibbli	18 ta’ Settembru, 2013

8. Garanzija u Appoġġ

Specific warranty details for the ACI 377140 Windshield Washer Pump are typically provided at the point of purchase or can be found on the manufacturer's official websit. Jekk jogħġbok żomm il-prova tax-xiri tiegħek għal kwalunkwe talba ta' garanzija.

For technical support, installation assistance, or warranty inquiries, please contact ACI customer service or the retailer from whom the product was purchased. Always refer to the official ACI resources for the most accurate and up-to-date information.

	Gwida għall-Installazzjoni għall-Kondizzjonaturi tal-Arja bil-Kassetta tas-Serje ACI Istruzzjonijiet dettaljati għall-installazzjoni tal-arja kondizzjonata cassette tas-serje ACI, inklużi prekawzjonijiet ta' sigurtà, dimensjonijiet tal-immuntar, u proċeduri ta' konnessjoni. Ikopri mudelli bħal ACI-25HRDC1C, ACI-35HRDC1C, ACI-53HRDC1C, ACI-71HRDC1A, ACI-105HRDC3A, ACI-140HRDC3A, u ACI-180HRDC3A.
	Installazzjoni u Tħaddim tas-Sensor tas-Serje tat-Trasmettitur tat-Temperatura u l-Umdità tal-Kanal ACI Istruzzjonijiet għall-installazzjoni u t-tħaddim għas-Sensors tas-Serje tat-Trasmettituri tat-Temperatura u l-Umdità fil-Kanali tal-ACI (A/TT u A/RH). Tkopri informazzjoni ġenerali, immuntar, wajers, kalibrazzjoni, issolvi l-problemi, u speċifikazzjonijiet tal-prodott għal sistemi ta' ġestjoni tal-bini HVAC.
	Manwal tal-Installazzjoni u t-Tħaddim tas-Sensor tas-Serje tal-Kamra ACI BACnet/Modbus Gwida komprensiva għall-installazzjoni u t-tħaddim għas-sensuri tat-temperatura u l-umdità tas-Serje tal-Kamra ACI BACnet MS/TP u Modbus RTU. Tkopri l-wajers, l-immuntar, il-konfigurazzjoni, u l-ispeċifikazzjonijiet għas-sistemi ta' ġestjoni tal-bini.
	Ripetitur tal-Ispettru Mifrux ACI RR2552: Istruzzjonijiet għall-Installazzjoni u t-Tħaddim Gwida komprensiva għall-installazzjoni u t-tħaddim tal-ACI RR2552 Spread Spectrum Repeater, li tkopri s-setup, il-konfigurazzjoni tal-ID tan-netwerk, l-immuntar, il-wajers, is-soluzzjoni tal-problemi, u l-ispeċifikazzjonijiet tal-prodott.
	Manwal ta' Installazzjoni u Tħaddim tas-Swiċċ tal-Istatus Aġġustabbli ACI Mini Serje A/MCS-A, A/MSCS-A Istruzzjonijiet għall-installazzjoni u t-tħaddim għas-Serje ta' Swiċċijiet tal-Istatus Aġġustabbli ACI Mini (A/MCS-A, A/MSCS-A). Tkopri l-karatteristiċi, il-prekawzjonijiet, l-immuntar, il-wajers, il-kalibrazzjoni, is-soluzzjoni tal-problemi, u l-ispeċifikazzjonijiet tal-prodott għall-monitoraġġ tal-kurrent AC.
	Istruzzjonijiet għall-Installazzjoni u t-Tħaddim tas-Sensor tas-Serje ACI Freezer Gwida komprensiva għall-installazzjoni, it-tħaddim, u s-soluzzjoni ta' problemi tas-sensuri tat-temperatura tas-Serje ACI Freezer. Tinkludi speċifikazzjonijiet tal-prodott, dijagrammi tal-wajers, u struzzjonijiet tal-immuntar għal sistemi kummerċjali tal-HVAC u tal-ġestjoni tal-bini.

ACI 377140