1. Introduzzjoni
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Belimo LMB24-3-T non-spring return damper actuator. Designed for precise control in HVAC systems, this actuator offers reliable performance for various damper applications. Please read this manual thoroughly before installation and operation to ensure safe and efficient use.
2. Informazzjoni dwar is-Sigurtà
Dejjem osserva l-prekawzjonijiet ta' sigurtà li ġejjin biex tevita korrimenti personali u ħsara lit-tagħmir:
- L-installazzjoni u l-wajers għandhom isiru minn persunal kwalifikat skont il-kodiċijiet elettriċi lokali u nazzjonali kollha.
- Disconnect power before installing, servicing, or removing the actuator.
- Tħaddimx l-attwatur lil hinn mill-volum speċifikat tiegħutage and torque limits.
- Żgura ertjar xieraq biex tevita xokk elettriku.
- Protect the actuator from moisture and extreme temperatures outside its operating range.
3. Prodott Aktarview
The Belimo LMB24-3-T is a direct-mount, non-spring return damper actuator designed for modulating control of air dampers in HVAC systems. It operates on 24VAC/DC power and provides a 0-95 degree rotation with a 45 in-lb (5 Nm) torque output. Its floating signal input allows for precise positioning.
Figura 1: Belimo LMB24-SR Damper Actuator. This image displays the Belimo LMB24-SR non-spring return damper actuator. The actuator is orange and grey, showing its direct mount mechanism and electrical connection block. Visible text on the actuator includes 'BELIMO', 'Made in Switzerland', 'LMB24-SR', '5Nm 45in-lb', '24VAC/DC', '150s', '2VA 1W', 'Input 2... 10V', 'NEMA2 IP54', and certification marks like UL and CE. A wiring diagram is clearly visible on the black connection block, detailing connections for COM I, RD, WH Y, OG U, PK C1, and GY C2.
Karatteristiċi ewlenin:
- Mudell: LMB24-3-T (Image shows LMB24-SR, which is a similar model)
- Torque: 45 fil-lb (5 Nm)
- Provvista tal-Enerġija: 24VAC/DC
- Angolu ta' Rotazzjoni: 0-95 Grad
- Tip ta' Sinjal: F'wiċċ l-ilma
- Return Type: Non-Spring Return
- Klassi ta' Protezzjoni: NEMA2 IP54
- Run Time: 150 seconds (for 90 degrees)
- Konsum tal-Enerġija: 2VA / 1W
- Ċertifikazzjonijiet: Elenkat UL, CE
4. Setup u Installazzjoni
Follow these general steps for proper installation. Refer to specific wiring diagrams for your application.
4.1 Immuntar
- Żgura li damper shaft is clean and free of obstructions.
- Żerżaq l-attwatur fuq id-damper shaft. The direct mount design allows for easy attachment.
- Secure the actuator firmly to the damper shaft using the provided hardware. Ensure the actuator is aligned correctly with the damper blade's movement.
4.2 Wajers
The actuator requires a 24VAC/DC power supply. The floating signal input allows for control based on the duration of the control signal. Refer to the wiring diagram on the actuator (as shown in Figure 1) for specific terminal connections.
Typical Wiring (refer to actuator label for exact pinout):
- 1 BK (Black): COM I (Common Input)
- 2 RD (Red): ~+ (Power Supply +)
- 3 WH (White): Y ~+ (Control Signal Input)
- 5 OG (Orange): U (Feedback Signal Output)
- 6 PK (Pink): C1 (Auxiliary Contact 1)
- 7 GY (Grey): C2 (Auxiliary Contact 2)
Ensure all connections are secure and insulated. Verify correct voltage qabel ma tapplika s-setgħa.
5. Istruzzjonijiet Operattivi
The LMB24-3-T operates with a floating control signal. This means the actuator's position is determined by the duration of the control signal applied to the 'Y' input (White wire) relative to the common. The actuator will rotate to its fully open or closed position based on the signal direction and duration.
- Applying a signal to 'Y' will cause the actuator to rotate in one direction.
- Reversing the polarity of the signal (or applying a signal to an alternative input if available) will cause rotation in the opposite direction.
- Removing the signal will cause the actuator to hold its last position.
- The actuator has a mechanical stop for setting the minimum and maximum rotation limits within the 0-95 degree range.
6. Manutenzjoni
The Belimo LMB24-3-T actuator is designed for maintenance-free operation. However, periodic inspection is recommended to ensure optimal performance:
- Spezzjoni Annwali: Check for any loose connections or signs of wear on the wiring.
- Tindif: Keep the exterior of the actuator clean and free of dust or debris. Do not use abrasive cleaners or solvents.
- DampOperazzjoni: Periodically verify that the damper operates smoothly and without excessive resistance, which could strain the actuator.
7 Issolvi l-problemi
If the actuator is not functioning as expected, refer to the following troubleshooting guide:
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| L-attwatur ma jiċċaqlaqx | Ebda provvista ta 'enerġija Wiring mhux korrett Damper jammed | Iċċekkja l-konnessjonijiet tal-enerġija u l-volumtage Ivverifika l-wajers mad-dijagramma Inspect damper for obstructions |
| Actuator moves in wrong direction | Incorrect control signal polarity | Reverse control signal polarity (if applicable) or check control logic |
| Actuator does not reach full travel | Mechanical stops incorrectly set Damper obstruction Insufficient control signal duration | Adjust mechanical stops Clear damper obstruction Ensure control signal is applied for sufficient time |
| L-attwatur jagħmel ħoss mhux tas-soltu | Damper binding Ħsara interna | Iċċekkja damper for smooth operation Contact Belimo support if noise persists |
8. Speċifikazzjonijiet
| Parametru | Valur |
|---|---|
| Mudell | LMB24-3-T |
| Provvista tal-Enerġija | 24 VAC/DC |
| Torque | 45 fil-lb (5 Nm) |
| Angolu ta' Rotazzjoni | 0-95 Grad |
| Sinjal ta 'Kontroll | F'wiċċ l-ilma |
| Run Time (for 90°) | 150 sekonda |
| Konsum tal-Enerġija | 2 VA / 1 W |
| Klassi ta' Protezzjoni | NEMA2 / IP54 |
| Dimensjonijiet tal-Prodott | 2.28 x 2.64 x 2.28 pulzieri |
| Piż | 1 Lira |
| Ċertifikazzjonijiet | Elenkat UL, CE |
9. Garanzija
The Belimo LMB24-3-T Damper Actuator comes with a garanzija ta 'sena from the date of purchase, covering defects in materials and workmanship under normal use. For detailed warranty terms and conditions, please refer to the official Belimo warranty statement or contact Belimo customer support.
10. Appoġġ
For technical assistance, product inquiries, or warranty claims, please contact Belimo customer support. Have your product model number and serial number ready when contacting support to expedite the process.
You can find contact information on the official Belimo webis-sit jew permezz tad-distributur lokali tiegħek.
