Dwyer Magnehelic Series 605 Differential Pressure Indicating Transmitter User Manual

Introduzzjoni

The Dwyer Magnehelic Series 605 Indicating Transmitter is designed for both visual monitoring and electronic control of very low differential pressure. This device is suitable for control applications in building HVAC systems, providing local indication for routine maintenance and system troubleshooting. It combines the reliable Dwyer Magnehelic gauge mechanical design with Series 600 transmitter technology, offering a two-wire, 4-20 mA control signal. The terminal strip on the rear simplifies connection to any 4-20 mA control loop powered by a 10-35 VDC supply.

Figura 1: Quddiem view of a Dwyer Magnehelic Indicating Transmitter. The dial displays pressure in inches of water, with a visible range from 0 to 1.0. The face includes the "Magnehelic" brand, "Indicating Transmitter" label, maximum pressure rating (25 PSIG), and patent information. Adjustment screws for "SPAN" and "ZERO" are visible at the bottom, along with the Dwyer logo. Note that the specific model 605-3 covered in this manual has a 0-3.0"WC range.

Informazzjoni dwar is-Sigurtà

Read this manual thoroughly before installing, operating, or servicing this device. Failure to follow these instructions may result in product damage, property damage, or serious injury. Keep this manual for future reference.

• Kun żgur li l-konnessjonijiet elettriċi kollha jikkonformaw mal-kodiċijiet elettriċi lokali u nazzjonali.
• Disconnect power before making any wiring connections to prevent electrical shock.
• Do not exceed the maximum pressure rating of 25 PSIG.
• L-installazzjoni u s-servizz għandhom isiru biss minn persunal ikkwalifikat.

Speċifikazzjonijiet

Setup u Installazzjoni

Immuntar

The Series 605 can be flush mounted or surface mounted. Ensure the mounting location is free from excessive vibration and within the specified operating temperature range. The device should be mounted vertically for accurate readings.

1. Agħżel post xieraq għall-immuntar.
2. Secure the transmitter using appropriate hardware (not included).
3. Ensure the pressure ports are accessible for tubing connections.

Konnessjonijiet ta' Pressjoni

Connect the pressure tubing to the high and low pressure ports located on the back of the unit. Use appropriate tubing and fittings for the application. The high pressure port is typically marked "HIGH" or "+", and the low pressure port "LOW" or "-".

• Qabbad is-sors ta' pressjoni ogħla mal-port "GĦOLJA".
• Connect the lower pressure source to the "LOW" port.
• Kun żgur li l-konnessjonijiet kollha ma jnixxux.

Wiring Elettriku

The Series 605 utilizes a two-wire, 4-20 mA output. Connect the transmitter to a 10-35 VDC power supply and the control system as follows:

• Connect the positive (+) terminal of the power supply to the positive (+) terminal of the transmitter.
• Connect the negative (-) terminal of the transmitter to the input of the control system (e.g., PLC, DCS).
• Complete the loop by connecting the return of the control system to the negative (-) terminal of the power supply.
• Kun żgur li l-polarità hija xierqa biex tevita l-ħsara.

Operazzjoni

Qawwa Mixgħul

Once all connections are secure, apply power to the unit. The analog output will begin to transmit a 4-20 mA signal corresponding to the measured differential pressure.

Qari tal-Wiri

The Magnehelic gauge provides a local visual indication of the differential pressure. The red pointer on the dial indicates the current pressure in inches of water column ("WC").

Aġġustament Żero u Span

The Series 605 features external zero and span adjustments. These adjustments affect both the visual indication and the 4-20 mA output.

1. Aġġustament żero: With no pressure applied (both ports open to atmosphere or connected to the same pressure), adjust the "ZERO" screw (typically located at the bottom right of the dial) until the pointer reads 0"WC. This also calibrates the 4 mA output.
2. Aġġustament tal-firxa: Apply a known full-scale pressure (e.g., 3.0"WC for a 0-3.0"WC range). Adjust the "SPAN" screw (typically located at the bottom left of the dial) until the pointer reads the full-scale value. This calibrates the 20 mA output. Repeat zero and span adjustments as necessary for optimal accuracy.

Manutenzjoni

The Dwyer Magnehelic Series 605 is designed for minimal maintenance. Regular checks ensure continued accuracy and reliable operation.

• Kalibrazzjoni Perjodika: It is recommended to periodically verify the zero and span calibration, especially if accuracy is critical or after significant environmental changes.
• Tindif: Keep the exterior of the unit clean. Use a soft, damp drapp. Tużax tindif jew solventi li joborxu.
• Pressure Port Inspection: Periodically inspect pressure tubing and connections for leaks or blockages.
• Kundizzjonijiet Ambjentali: Kun żgur li l-ambjent operattiv jibqa' fil-firxiet speċifikati tat-temperatura u l-umdità.

Issolvi l-problemi

Garanzija u Appoġġ

Dwyer Instruments, Inc. warrants this product to be free from defects in material and workmanship for a period of one year from the date of shipment. For full warranty details, technical support, or service, please contact Dwyer Instruments directly. Contact information can be found on the official Dwyer websit.

Dwyer Instruments, Inc.
Belt ta' Michigan, IN 46360 L-Istati Uniti tal-Amerika
www.dwyer-inst.com