Manwal tal-Istruzzjonijiet tas-Sostituzzjoni tal-Bozza Aloġena tas-Serje Eiko H1155 H11

Introduzzjoni

This manual provides essential instructions for the safe and effective installation, operation, and maintenance of your Eiko H1155 H11 Series Halogen Replacement Bulb. Please read this manual thoroughly before installation and retain it for future reference.

Informazzjoni dwar is-Sigurtà

• TWISSIJA: Dejjem kun żgur li l-ignition tal-vettura tkun mitfija u l-batterija tkun skonnettjata qabel ma tipprova xi xogħol elettriku.
• ATTENZJONI: Halogen bulbs operate at high temperatures. Allow the bulb to cool completely before handling.
• ATTENZJONI: Avoid touching the glass part of the bulb with bare hands. Oils from your skin can create hot spots, leading to premature failure. Use clean gloves or a clean cloth.
• TWISSIJA: Armi l-bozoz qodma b'mod responsabbli skont ir-regolamenti lokali.

Prodott Overview

The Eiko H1155 is a high-performance H11 series halogen replacement bulb designed to meet or exceed original equipment specifications. It features a tungsten filament for bright, white light output.

Figura 1: Eiko H1155 H11 Series Halogen Replacement Bulb. This image shows the clear glass bulb with its internal tungsten filament, mounted on a metal base with a red rubber seal and a black plastic connector.

Setup u Installazzjoni

1. Preparazzjoni: Ensure the vehicle is parked on a level surface, the engine is off, and the parking brake is engaged. Disconnect the negative terminal of the vehicle's battery to prevent accidental electrical shorts.
2. Aċċessa l-Bozza: Locate the headlight assembly. Depending on your vehicle model, you may need to remove a cover, fender liner, or other components to access the rear of the headlight housing. Consult your vehicle's owner's manual for specific access instructions.
3. Skonnettja l-Wiring: Carefully disconnect the electrical connector from the back of the old bulb.
4. Neħħi l-Bozza Qadima: Unclip or twist the retaining mechanism that holds the old bulb in place. Gently pull the old bulb straight out from the housing.
5. Installa Bozza Ġdida: Wearing clean gloves or using a clean cloth, carefully insert the new Eiko H1155 bulb into the headlight housing. Ensure it is seated correctly and the retaining mechanism is secured. Do not touch the glass bulb with bare hands.
6. Erġa' qabbad il-wajers: Reconnect the electrical connector to the new bulb.
7. Funzjonalità tat-Test: Reconnect the vehicle's battery. Turn on the headlights to verify the new bulb is functioning correctly.
8. Erġa' arma: Reinstall any covers or components that were removed to access the bulb.

Nota: It is recommended to replace both headlamps simultaneously for consistent light output and performance, as bulbs dim over time.

Operazzjoni

The Eiko H1155 Halogen Replacement Bulb operates as part of your vehicle's existing electrical system. Once properly installed, it will illuminate when the vehicle's headlight switch is activated. No special operational procedures are required beyond standard vehicle headlight usage.

Manutenzjoni

• Tindif: If the headlight lens becomes dirty, clean it with a soft cloth and appropriate automotive cleaning solution. Avoid abrasive cleaners.
• Spezzjoni: Periodically check your headlights for proper function. If a bulb appears dim or has failed, replace it promptly.
• Immaniġġjar: When replacing bulbs, always handle them by the base to avoid contaminating the glass.

Issolvi l-problemi

Speċifikazzjonijiet

Garanzija u Appoġġ

For warranty information or technical support regarding your Eiko H1155 Halogen Replacement Bulb, please refer to the manufacturer's official website or contact Eiko customer service directly. Keep your purchase receipt as proof of purchase.

Manufacturer: EIkO Auto Lighting