Chief TS325TU Medium THINSTALL Dual Swing Arm Wall Display Mount

Introduzzjoni

The Chief TS325TU Medium THINSTALL Dual Swing Arm Wall Display Mount is designed to provide a secure and versatile mounting solution for flat panel displays ranging from 30 to 52 inches. This mount offers an ultra-low profile when collapsed and extends up to 25 inches, allowing for optimal viewing angles with its Centris low-profile tilt and Centerless lateral shift capabilities. It features integrated cable management for a clean installation.

Informazzjoni dwar is-Sigurtà

TWISSIJA: Failure to read, understand, and follow all instructions can result in serious personal injury, property damage, or voiding of product warranty. If you have any questions, contact Chief customer service or a qualified installer.

• Teċċedix il-kapaċità massima tat-tagħbija ta' 75.00 lb (34 kg).
• Kun żgur li l-wiċċ tal-immuntar jista' jsostni b'mod sikur il-piż ikkombinat tal-immuntar u d-displej.
• Always mount to structural studs or appropriate wall anchors. Note that this mount is designed for studs approximately 16 inches apart.
• Use appropriate tools and follow all local building codes.
• Żomm it-tfal u l-annimali domestiċi 'l bogħod waqt l-installazzjoni.

Kontenut tal-Pakkett

Iċċekkja li l-komponenti kollha huma preżenti qabel tibda l-installazzjoni:

• 1 x Main Assembly
• 1 x Wall Rail
• 1 x Right Upright
• 1 x Left Upright
• 1 x Top Interface Support
• 1 x Bottom Interface Support
• 2 x Wall Rail Cover
• 1 x Lag Screw Cover
• 1 x Bumper
• 1 x Latch Spacer
• 2 x Long Adhesive
• 4 x Short Adhesive
• Mounting Hardware (various screws, washers, spacers)

Setup u Installazzjoni

Proper installation is critical for the safety and performance of your display mount. It is recommended to have at least two people for installation due to the weight and size of the mount.

Għodod Meħtieġa (Mhux Inklużi):

• Finder Stud
• Drill bi drill bits xierqa
• Livell
• Tape Measure
• Socket Wrench / Ratchet
• Tornavit tar-ras Phillips
• Lapes

Installazzjoni pass pass:

1. Ipprepara l-Ħajt:

   Locate and mark the center of two adjacent wall studs. This mount is designed for standard 16-inch stud spacing. Ensure there are no electrical wires or plumbing in the drilling path. It is highly recommended to plan your entire layout, including TV, speakers, and wiring, before drilling.

2. Attach Wall Rail:

   Position the Wall Rail on the marked studs, ensuring it is level. Mark the pilot hole locations. Drill pilot holes into the studs. Secure the Wall Rail to the wall using the provided lag screws. Ensure the screws are tightened securely but do not overtighten to avoid stripping.

   

   Image: Main assembly of the Chief TS325TU mount, showing the wall plate, articulating arms, and display interface.

3. Assemble Display Interface:

   Attach the Right and Left Uprights to the back of your display using the appropriate screws, washers, and spacers from the mounting hardware kit. Ensure the uprights are centered and level on the display. Then, attach the Top and Bottom Interface Supports to the uprights.

4. Mount Display to Wall Rail:

   Carefully lift the display with the attached interface and hook it onto the Wall Rail. The design allows for post-installation lateral shift of up to 16 inches (406 mm) for limitless centering capability. Secure the display to the mount according to the specific instructions in the detailed manual (refer to manufacturer's full manual for precise steps).

   

   Immaġni: Ġenb view of the Chief TS325TU mount, illustrating its compact profile when retracted and the extension capability.

5. Ġestjoni tal-Kejbil:

   Utilize the enclosed, tool-free cable covers and the wide open wall plate to route power and signal cables. This helps maintain a clean and organized appearance.

Tħaddim tal-Muntanja

The Chief TS325TU mount offers flexible positioning for your display:

• Estensjoni: The mount extends up to 25 inches (635 mm) from the wall, maximizing viewing potential from various positions in the room.
• Mejjel: The Centris low-profile tilt mechanism allows for up to 15 degrees of effortless fingertip tilt. This enables you to achieve optimal viewing angles and reduce glare.
• Dawwar/Pan: The dual swing arms allow for significant swivel capabilities, enabling you to turn the display left or right to suit your viewbżonnijiet.
• Lateral Shift: After installation, the display can be shifted laterally along the wall plate by up to 16 inches (406 mm) to fine-tune its horizontal position without re-drilling.

Immaġni: Angolata view of the Chief TS325TU mount, highlighting its robust construction and articulating design.

Manutenzjoni

Regular maintenance ensures the longevity and safe operation of your mount:

• Tindif: Neħħi t-trab mill-muntatura regolarment b'ċarruta ratba u niexfa. Għal marki iebsa, uża ċarruta kemxejn ratba.amp cloth with mild soap, then wipe dry. Avoid abrasive cleaners or solvents.
• Iċċekkja l-Konnessjonijiet: Periodically check all screws and bolts to ensure they remain tight. Do not overtighten.
• Kontroll tal-Moviment: Occasionally extend, retract, tilt, and swivel the mount to ensure smooth operation. If movement becomes stiff, consult the troubleshooting section or contact support.

Issolvi l-problemi

For complex issues or if you are unsure about any step, please contact Chief customer support or a certified installer.

Speċifikazzjonijiet

Garanzija u Appoġġ

For detailed warranty information, please refer to the official Chief Manufacturing website or the documentation included with your product. Chief provides support for their products to ensure customer satisfaction.

If you require technical assistance, have questions about installation, or need to report a missing part, please visit the official Chief Manufacturing support page or contact their customer service directly. Contact information can typically be found on their websit:

Visit Chief Manufacturing Websit